Specifications, Projector specifications, Dimensions | BenQ SP920P

English

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution

1024 x 768 XGA

Display system 1-CHIP DMD

Lens F/Number

F=2.4 to 2.55, f=23.88 to 27.46 mm

Lamp

280 W lamp x 2

Electrical

Power supply

AC 100–240 V, 7.7 A, 50-60 Hz (Automatic)

Power consumption

805 W (Max); 5 W (Standby)

Mechanical

Weight 11 kg

Output terminals

RGB output

D-Sub 15-pin (female) x 1

Speaker

(Stereo) 5 watt x 2 12 VDC (Max. 1 A)

Control

USB serial control

Type mini B

RS-232 serial control

Mini Din 8 pin x 1

Dimensions

443.0mm (W) x 167.0 mm (H) x 355.0 mm (D)

355.0

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 1 DVI-D input

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3, D-Sub 15-pin

Digital - DVI-D (supports HDCP) Digital - HDMI

Audio signal input Audio in

PC audio jack x 1

Wire remote

2.5 mm wire jack

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C

1500–3000 m at 0°C–30°C (with High Altitude Mode on)

443.0

167.0

63.85 85.50

52 Specifications

Image 52

BenQ SP920P user manual Specifications, Projector specifications, Dimensions

Contents

Welcome SP920P Digital Projector Table of contents Important safety instructions With all windows rolled upCigarette smoke may contaminate optical 3000 m 10000 feet Important safety instructions Ceiling mounting the projector Projector features Introduction Shipping contents Projector exterior view RGB signal output socketFront/upper side Rear/lower side Controls and functions Projector Mode Mute Remote control effective range Making the remote control a wired controlOperating the Laser pointer Operating the projector from the front Positioning your projector Choosing a location Obtaining a preferred projected image size Select your screen size Projection dimensions Zoom Connecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computer To connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Connecting Video source devices Connecting AudioBest video quality Better video quality Connecting a Hdmi source device To connect the projector to a Hdmi source device Connecting a DVI-D source device To connect the projector to a DVI-D source device Connecting a Component Video source device To connect the projector to a Component Video source deviceWith a Component Video cable With a Component Video to VGA D-Sub adaptor cable Connecting an S-Video or a composite Video source device To connect the projector to an S-Video/Video source device Operation Starting up the projector Using the On-Screen Display OSD menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projector Utilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXIT Entering the password recall procedure Changing the passwordDisabling the password function Confirm the new password by re-entering the new password Switching input signal Changing Color Space Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Magnifying and searching for details Correcting keystone Selecting the aspect ratio About the aspect ratio Using Wall Color Selecting a picture modePC input signals D-Sub/Comp. analog RGB and DVI-D DVI-D Optimizing the image Fine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant Color3D Color Management Setting the presentation timer Repeat steps 3 to 6 for other color adjustmentsPress MENU/EXIT to exit and save the settings Follow these steps to utilize this function To cancel the timer, perform the following steps How to use the Timer ON/SHOW key?Using the remote control Using the OSD menu Utilizing FAQ function Possible solutions To exit the OSD menu, press MENU/EXITHiding the image Freezing the image Press / or go to the System Setup Basic Panel Key Lock To activate the High Altitude ModeLocking control keys Operating in a high altitude environment Adjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Creating your own startup screen Setting the lamp mode Personalizing the On-Screen Display OSD menus Shutting down the projector Menu structure On-Screen Display OSD MenusMain menu Sub-menu Options Setup Basic Advanced Description of each menu Presentation Timer Auto Power OffBlank Timer Sleep Timer Lamp Settings Security SettingsReset All Settings FAQ-Image Installation Care of the projector MaintenanceLamp information Setting Lamp Mode as Dual-Reliable Setting Auto Power OffExtending lamp life Timing of replacing the lamp Replacing the lamp Screwdriver Remove the lamp cover from the projector Resetting the corresponding lamp timer Go to the System Setup Advanced Lamp Settings menuRestart the projector Way into the projector Indicators Troubleshooting Projector specifications SpecificationsDimensions Timing chart Supported timing for Analog RGB inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputs Resolution Horizontal Vertical Pixel Frequency ModeSupported timing for DVI-D and Hdmi Hdcp input Frequency kHz Frequency Hz MHz Other information Regulation statements English