Wiring OctoPOPITs, Line Termination | Bosch Appliances D7212G

D7212G

Off-board Points

Mounting

Follow the procedure below to install OctoPOPITs in the enclosure.

1.It is easier to set the switches on the D8128D before mounting it in the enclosure. See Section 8.4.5 Line Termination below and Section 8.4.7 Address Assignment Switches on page 44.

2.Align the OctoPOPIT Module with any of the four mounting locations in the enclosure. See Figure 2 on page 21.

3.Use the screws provided with the module to secure it in the enclosure.

4.Use the D137 Mounting Bracket to install OctoPOPITs in enclosures with no module mounting locations available.

8.4.4Wiring OctoPOPITs

Follow the procedure below to wire D8128D OctoPOPIT Modules to the D7212G. Both OctoPOPIT and POPEX Modules can be connected to the same Point Bus terminals. The modules wire in parallel. Remember, never assign the same point number to more than one point.

1.Power down first: Power down the panel by disconnecting the positive (red) battery lead at the battery and unplugging the transformer.

2.Connect Terminal 1 on the OctoPOPIT to Terminal 9 on the D7212G.

3.Connect Terminal 2 on the OctoPOPIT to Terminal 28 on the panel if assigning point numbers from 9 to 40 to this OctoPOPIT. See Section 8.4.7 Address Assignment Switches on page 44.

4.Connect Terminal 3 on the OctoPOPIT to Terminal 27 on the D7212G.

5.Connect Terminal 4 on the OctoPOPIT to Terminal 3 on the D7212G.

6.See Section 8.4.6 OctoPOPIT Sensor Loops on page 44 for instructions on connecting devices to the OctoPOPIT’s sensor loops.

8.4.5Line Termination

Switch 5 sets line termination.

If there is:

·No D8125 POPEX module connected to ZONEX 1, set switch 5 of only one D8128D connected to those terminals to the ON position.

·A D8125 POPEX module connected to ZONEX 1, set switch 5 of all D8128Ds connected to those terminals to the OFF position.

See Figure 15 on page 45 for the location of the switches on the OctoPOPIT.

D7212G Operation and Installation Guide

© 2003 Bosch Security Systems

Page 43

4998138544C

Image 43

Bosch Appliances D7212G manual Wiring OctoPOPITs, Line Termination

Contents

Control/Communicator D7212G D7212G Operation and Installation Guide Contents 11.1 10.111.2 11.0 10.0 13.0 Figures Tables D7212G Operation and Installation Guide Organization Appendix Description IntroductionGuide Organization Section Description Documentation Conventions Related DocumentationType Styles Used in the Text Tips, Notes, Cautions and Warnings FCC RulesPart D7212G Overview New Features D9412G D7412G D7212G9000G Series Panel Differences Secondary Specifications Telephone Connections Telephone Line Introduction Features in D7212GCompatible Accessories Ground Fault Detect Standard Features Model Display Application Control/Communicator Assembly Other FeaturesComponents and Literature Available by Separate Order Burglary Listings and ApprovalsListings Enclosure Options InstallationBeginning the Installation Before Beginning Locking the Reset Pin Installing the AssemblyConnecting Earth Ground Ground Fault Detect Enable Install Modules and Relays Finishing the InstallationCharge the Battery While Finishing Install and Wire Detection Devices Testing the System Install the Point Chart LabelProgramming the Panel Primary Power Terminals Power SupplySecondary Power Terminals Replacing the Battery Installing the Battery Discharge Cycle Battery SupervisionBattery Charging Circuit Float Charge Battery Discharge/Recharge Schedule Color State Charging Status and Low Battery LEDsType Action Programmable Power Outputs Terminals Power OutputsTotal Available Power Aux Power Terminals Continuous Current Draw Verification/Reset Relay Relay InstallationAvailable Power Fire System Power Formula Telephone Connections Called Party Disconnect Operation Monitor LED GreenDialing Format Phone Line Monitor Position Ground Start Ground StartPhone Monitor Select Jumper Loop Start D7212G Point Parameters On-board PointsDescription Terminals Point Sensor Loops Bell Point Zonex Bus D7212G Terminals Off-board Points D8125, D8127 and D9127 Popit Modules Installing the D8125 Popex Module Popit Sensor Loops Wiring Data Expansion Loops to Popex ModulesExpansion Loops Combined Length in ft. m Connecting the D8125 Popex to the D7212G Panel Program Record Sheet Popit Module Point AssignmentsRadxpnts Handler Description Installing the OctoPOPITD8128D OctoPOPIT Module Popit Labels Line Termination Wiring OctoPOPITs OctoPOPIT Sensor Loops Testing Off-board PointsAddress Assignment Switches D8128D Address Switches Connecting D8128D OctoPOPITs to the D7212G D7212G Off-board Relays Panel Relay D8129 OctoRelay D8129 OctoRelay Switch NumberD8129 OctoRelay D8129 Connections to the D7212G Arming Devices Command Center TerminalsAssigning the command center an address Address Switch Power at Command Centers D7212G Command Center Terminal Function Momentary Contact KeyswitchKeyswitch Operation Maintained Contact 10.3 D279A Independent Zone Control D7212G 11.3 D9131A Parallel Printer Interface Module InstallationPrinter Switch SDI Devices SDI Address 11.5.2 D9133TTL-E Network Interface Module Address Settings D7212G Programmer Access Reports Programmer and Accessory ConnectionsProgrammer Connector Accessory Connector Programmer and Accessory Connections AccessoryProgramming ConnectorConnector 13.1 D7212G Faceplate Faceplate 13.0 Faceplate D7212G Control/Communicator, 1 Appendix a System Wiring Diagrams, Issue a D7212G Control/Communicator, 2 D7212G System Wiring Diagram, 2 D7212G Control/Communicator, 3 D7212G System Wiring Diagram, 3 D7212G Zonex 1, Points 9 to Appendix B Point Address Chart D7212G Index Symbols Zonex