Zonex | Bosch Appliances D7212G specs

P

Phone Cords			31
Phone Lines			31
Dialing Format			32
Ground Start			33
Jacks		17,	31
Phone Line Monitor			32
Rng Indicator			32
Seizure		17,	31
Point Address Charts			65
ZONEX 1			65
Point Chart Label			24
Installing			24
Points			17
Off-board		17,	37
On-board	17,	24,	35
Sensor Loops			35
Standard Features			17
POPEX		23, 37
Wiring			38
POPITs		37, 38
Testing			44
Wiring		23,	38
Power
Auxiliary			29
Continuous Current Draw			29
Primary			25
Programmable Terminals			29
Secondary			25
Total Available			29
Power Failure			25
Power Module
Battery Discharge Schedule			27
Replacing Batteries			26
Power Outputs
Alarm			29
Alternate Alarm			29
Auxiliary			29
Circuit Protection			29
Continuous Power Outputs Terminals
29
Fire System Power Formula			30
Programmable			29
Programmable Power Outputs
Terminals			29
Switched Auxiliary			29
Total Available Power			29
Power Supply			25
Primary Power Terminals			25
Printer			53
Programmer			24
Connecting			57
Programmer Connector			57
Programming
Standard Features			18
Programming the Panel			24

R					Z
RAM IV			18, 24		ZONEX 1
Related Documentation				10	Point Address Charts	65
Remote Account Manager	.............		18, 24		ZONEX bus	47
Replacing Batteries				26
Reports				24
Transmission			16,	17
Watchdog Reset				27
Reset	22,	24,	30,	54
Watchdog			23,	27
Reset Pin				22
Ringer Equivalence				31
Rng Indicator				32
RS232				54
S
SDI Address 80				54
SDI Address 88				54
SDI Bus			50,	53
SDI Devices				54
Installing				53
Secondary Power Terminals				25
Sensor Loops				35
Serial Interface Module				54
Service Walk Test				24
Specifications				14
Standard Features				17
System Overview				13
T
Telephone Connections			24,	31
Testing
Off-board Points				44
Service Walk				24
Testing the System				24
Tips, Notes, Cautions & Warnings				11
Transformer			23,	25
Transformer Enclosure				25
Type Styles				10
V
Verification/Reset Relay				30
W
Warnings				11
Wiring				23
Command Centers				23
D8125 POPEX				38
Detection Devices				23
Diagrams		61,	62,	63
OctoPOPITs				43
On-board Points				35
POPITs			23, 38

©2003 Bosch Security Systems	4998138544C	05/03
130 Perinton Parkway, Fairport, NY 14450-9199 USA	Operation and Installation Guide	D7212G
Customer Service: (800) 538-5807; Technical Support (888) 886-6189		Page 68 of 68

Image 68

Bosch Appliances D7212G manual Zonex

Contents

Control/Communicator D7212G Operation and Installation Guide D7212G Contents 11.2 10.111.1 10.0 11.0 13.0 Figures D7212G Operation and Installation Guide Organization Tables Introduction Guide OrganizationSection Description Appendix Description Type Styles Used in the Text Related DocumentationDocumentation Conventions Part FCC RulesTips, Notes, Cautions and Warnings D7212G 9000G Series Panel Differences New Features D9412G D7412G D7212GOverview Specifications Secondary Telephone Connections Telephone Line Features in D7212G Compatible AccessoriesGround Fault Detect Introduction Standard Features Model Display Application Components and Literature Available by Separate Order Other FeaturesControl/Communicator Assembly Listings Listings and ApprovalsBurglary Installation Beginning the InstallationBefore Beginning Enclosure Options Installing the Assembly Connecting Earth GroundGround Fault Detect Enable Locking the Reset Pin Finishing the Installation Charge the Battery While FinishingInstall and Wire Detection Devices Install Modules and Relays Programming the Panel Install the Point Chart LabelTesting the System Secondary Power Terminals Power SupplyPrimary Power Terminals Installing the Battery Replacing the Battery Battery Supervision Battery Charging Circuit Float ChargeBattery Discharge/Recharge Schedule Discharge Cycle Charging Status and Low Battery LEDs TypeAction Color State Power Outputs Total Available PowerAux Power Terminals Continuous Current Draw Programmable Power Outputs Terminals Relay Installation Available PowerFire System Power Formula Verification/Reset Relay Telephone Connections Operation Monitor LED Green Dialing FormatPhone Line Monitor Called Party Disconnect Ground Start Phone Monitor Select JumperLoop Start Position Ground Start D7212G On-board Points Description TerminalsPoint Sensor Loops Point Parameters Bell Off-board Points Point Zonex Bus D7212G Terminals Installing the D8125 Popex Module D8125, D8127 and D9127 Popit Modules Wiring Data Expansion Loops to Popex Modules Expansion Loops CombinedLength in ft. m Popit Sensor Loops Connecting the D8125 Popex to the D7212G Panel Radxpnts Handler Popit Module Point AssignmentsProgram Record Sheet Installing the OctoPOPIT D8128D OctoPOPIT ModulePopit Labels Description Wiring OctoPOPITs Line Termination Testing Off-board Points Address Assignment SwitchesD8128D Address Switches OctoPOPIT Sensor Loops Connecting D8128D OctoPOPITs to the D7212G D7212G D8129 OctoRelay Panel Relay D8129 OctoRelay D8129 OctoRelay Switch NumberOff-board Relays D8129 Connections to the D7212G Command Center Terminals Assigning the command center an addressAddress Switch Arming Devices D7212G Command Center Terminal Function Power at Command Centers Keyswitch Keyswitch Operation Maintained Contact10.3 D279A Independent Zone Control Momentary Contact D7212G Installation Printer SwitchSDI Devices 11.3 D9131A Parallel Printer Interface Module SDI Address Address Settings 11.5.2 D9133TTL-E Network Interface Module D7212G Programmer and Accessory Connections Programmer ConnectorAccessory Connector Programmer Access Reports AccessoryProgramming ConnectorConnector Programmer and Accessory Connections Faceplate 13.0 13.1 D7212G Faceplate Faceplate Appendix a System Wiring Diagrams, Issue a D7212G Control/Communicator, 1 D7212G System Wiring Diagram, 2 D7212G Control/Communicator, 2 D7212G System Wiring Diagram, 3 D7212G Control/Communicator, 3 D7212G Appendix B Point Address Chart Zonex 1, Points 9 to D7212G Symbols Index Zonex