Test Label Examples, Configuration Test Label | Brady 2024, 2034

The Self-Test may also be initiated while the power is on by simultaneously pressing the PAUSE and CANCEL buttons. Simultaneously release them and immediately press and hold the FEED button until the ribbon/media LED flashes.

NOTE: If any configuration errors are indicated by the Self-Tests, check the Printer's dip switch settings or configuration setup.

3.3.1 Test Label Examples

The first test label printed will be the Configuration Label, this label lists the Printer's configuration and status. The following sample was produced on a standard printer without the test plugs installed.

FRI	SEPTEMBER 23, 1996 10:12 340
VER:		GA	-		1.14		01/30/96
ROM	CHECKSUMS
U13		47-2091-01P
U24		47-2090-01P
U34		47-2088-01B
U2		47-2089-01B
SYSTEM RAM CHECKS_ _ _ _ GOOD							SYSTEM RAM SIZE_ _ 512 KBYTES
SERIAL	PORT		BAUD		RATE	IS 9600			TRANSFER SWITCH IS ON
SWITCH 1		1		2	3	4	5	6	7	8
		ON		ON	ON	OFF	OFF	OFF OFF OFF
INTERNAL		1		2	3	4	5	6
		OFF		OFF	OFF	OFF	OFF	OFF
INPUT VALUES
PAPER:	255		EDGE:		253	REFL:	0 TEMP:			76
POT :	120		TOFA:		120	RIBN:	10		RWND:	0

COUNTER INFORMATION
ABSOLUTE VALUES	2-21-1996	RESETABLE VALUES	9- 5-1995
LENGTH_ _ _ _	2317 INCHES	LENGTH_ _ _ _	2317	TIME_ _ _ _
_ _	1 HOURS	TIME_ _ _ _ _ _	1 HOURS
MEMORY CONFIGURATION
INTERNAL MODULE_ _ _ _ _ _ _ _ 15		SCALABLE FONTS_ _ _ _ _ _ _ _ 0

Figure 3-4 Configuration Test Label

_______________________________________________________________________

34	Using Your Printer

Image 40

Brady 2024, 2034 manual Test Label Examples, Configuration Test Label

Contents

Logo W.H. Brady Co Automatic Indentification Products Part Number Revision D Agency Compliance and Approvals Important Safety Instructions Contents Appendix a Introduction Introduction Mechanism Detail Technical Specifications ResolutionPrint Technology Print Speed Additional Options Standard Ribbon Sizes Label/Tag Media Specifications Media Specifications Getting Started Unpacking Checking the AC Power Requirements Selecting 230 VAC Operation Selecting 230 VAC Connecting the Printer Rear Printer Connections Interfacing to the Printer Interface Cable Applications Dip Switch Settings Communications Dip Switch Settings Installation of a Memory Cartridge Memory Cartridges Media Access Media Loading 5a Media Installation 3 core 5b Media Installation Using the Optional Internal Rewind Installing the Arc Plate for Internal rewind Installing Media with Internal Rewind Option Using the Peel and Present Option Using the Peel and Present Option Installing Media using Peel and Present Option Ribbon Installation and Removal Ribbon Installation 11 Ribbon Installation showing J-hook Ribbon Removal 12 Selecting Ribbon On Thermal Transfer Using Your Printer Front Control Panel On position. This Switch is not present on LCD/Keypad Front Panel OptionPotentiometer is not present on the LCD/Keypad Front Panel Option Optional LCD/Keypad Front Panel Optional LCD/Keypad Front Panel Using the Optional LCD/Keypad Front Panel Shift Basic Function Basic Function Ribbon Saver Advanced Setup Basic Function TOF Adjust Advanced Setup Operation Advanced Setup Maintenance Power On Self-Test Self-Test Configuration Test Label Test Label Examples Printhead Test Label Configuration Test Label Internal Dip Switch Settings Using Your Printer Character Dump Mode Ascii Character Dump Label Factory Default Setup Fuse Replacement Using Your Printer Printing Labels Programming Commands Immediate Commands System Level Commands Char Description Format XMFname Label Formatting Commands Description Format +pii Special Label Formatting Commands Bitmapped Font Loading Commands Programming Example Printing Bar Codes Field Example line Printing Lines and Boxes Maintenance and Adjustments Printer Maintenance schedules Cleaning the Printhead Cleaning the Printhead Troubleshooting Printer does not print Possible cause and solution Poor print quality Possible cause and solution Media slips or does not properly advance Optional LCD/Keypad Front Panel Alarms LCD Display Alarm Description Cutter NotEQP Mechanical AdjustmentsRibsvr NotEQP Media Width Adjustment Media Width Adjustment Media Sensor Adjustment Media Sensor Adjustment Printhead Replacement Removal Replacement Printhead Removal Maintenance and Adjustments Appendix a Ascii Control Code Chart Char Dec Hex XON = DC1XOFF = DC3 Ascii Control Code Chart Appendix B Available Fonts and Bar Codes Human-Readable Fonts Table B-1 Human-Readable Font SizesFont Valid Ascii Characters, Decimal Table B-2 Valid Human-Readable Font Ascii Characters Appendix B Appendix B Bar Code Fonts Table B-3 Valid Bar Code Font Ascii Characters Appendix B Barcode O Appendix B Barcode S Barcode T Barcode z Appendix B Error Codes Appendix C Appendix C Support Services Appendix D Brady Company Customer Service Form Product Service and Support Programs Appendix D Appendix E Warranty Information Thermal Printhead Warranty Service Procedures General Warranty Provisions Limitation of Liability Appendix E