Manuals / Brady / Computer Equipment / Printer

Brady 2024, 2034 manual Configuration Test Label, 1 Internal Dip Switch Settings

Models: 2034 2024

1 89

Download 89 pages 6.73 Kb

Page 42

3.3.2 Configuration Test Label

The following are explanations of the Configuration Test Label elements, top to bottom, (see Figure 3-5).

Rom Checksums − indicates whether the ROMs that store the Printer's program and resident fonts are 'good' or 'bad'. Good part numbers are displayed normally. Checksum values replace the part numbers to indicate an error. If either the ROM or RAM test is bad, service is required.

System Ram Checks − indicates 'good' or 'bad'.

System Ram Size − indicates the amount of available RAM in the Printer.

Thermal Transfer Switch − Should be 'on' if using a ribbon, and 'off ' if in the direct-thermal mode (no ribbon).

Switch 1 − indicates the status of dip switch 1 on the rear of the printer, (see Section 2.3.2, Table 2-3).

Internal − indicates the status of the Printer's internal dip switch located on the main logic board (see Table 3-1).

Paper − this value indicates when paper is present in the sensor.

Edge and Refl − indicates when media is present at the respective sensor. These sensors tell the Printer where the start of the label is located. Refer to the Programmer's Manual when determining which sensing mode to use.

Switch Functions		1	2	3	4	5	6	7
RS-422	Disabled	OFF	OFF	OFF	X	X	X	X
RS-422	Address 1	ON	OFF	OFF	X	X	X	X
RS-422	Address 2	OFF	ON	OFF	X	X	X	X
RS-422	Address 3	ON	ON	OFF	X	X	X	X
RS-422	Address 4	OFF	OFF	ON	X	X	X	X
RS-422	Address 5	ON	OFF	ON	X	X	X	X
RS-422	Address 6	OFF	ON	ON	X	X	X	X
RS-422	Address 7	ON	ON	ON	X	X	X	X
Spare		X	X	X	OFF	X	X	X
Resettable Counter Reset		X	X	X	X	OFF	X	X
Spare		X	X	X	X	X	OFF	X
RS-422 Termination (hw)		X	X	X	X	X	X	OFF

Table 3-1 Internal Dip Switch Settings

_______________________________________________________________________

36	Using Your Printer

Image 42

Brady 2024, 2034 manual Configuration Test Label, 1 Internal Dip Switch Settings

Contents

Bradyprinterä THT Model 2024 and Thermal Transfer Printer User’s GuideLOGO W.H. Brady Co Automatic Indentification Products Part Number Revision D AGENCY COMPLIANCE AND APPROVALS IMPORTANT SAFETY INSTRUCTIONS Introduction CONTENTSUsing Your Printer Getting StartedAppendix A Maintenance and AdjustmentsPrinting Labels Appendix BIntroduction 1.0 IntroductionFigure 1-1 Overall View Figure 1-2 Mechanism Detail Print Technology 1.1 Technical SpecificationsResolution Print SpeedLCD/Keypad Additional OptionsOperating DRAM1.2 Standard Ribbon Sizes Table 1-1 Media Specifications 1.3 Label/Tag Media SpecificationsFigure 1-3 Media Dimensions DescriptionGetting Started 2.0 Introduction2.1 Unpacking 2.2 Checking the AC Power Requirements 2.2.1 Selecting 230 VAC Operation Figure 2-1 Selecting 230 VAC2.3 Connecting the Printer Figure 2-2 Rear Printer Connections2.3.1 Interfacing to the Printer “PC” DB25P to Printer Table 2-1 Interface Cable ApplicationsNull Modem MXM “PC” DB9P to Printer2.3.2 Dip Switch Settings Table 2-2 Communications Dip Switch Settings2.4 Memory Cartridges Figure 2-3 Installation of a Memory Cartridge2.5 Media Loading Figure 2-4 Media AccessFigure 2-5a Media Installation 3 core Figure 2-5b Media Installation 2.5.1 Using the Optional Internal Rewind Figure 2-6 Installing the Arc Plate for Internal rewindFigure 2-7 Installing Media with Internal Rewind Option 2.5.2 Using the Peel and Present Option Figure 2-8 Using the Peel and Present OptionFigure 2-9 Installing Media using Peel and Present Option 2.6 Ribbon Installation and Removal Ribbon InstallationFigure 2-10 Ribbon Installation Figure 2-11 Ribbon Installation showing J-hook Ribbon Removal Figure 2-12 Selecting Ribbon On Thermal Transfer3.1 Front Control Panel Using Your Printer3.0 Introduction Figure 3-1 Front Panelpotentiometer is not present on the LCD/Keypad on position. This Switch is not present on theLCD/Keypad Front Panel Option Front Panel Option3.1.1 Optional LCD/Keypad Front Panel Figure 3-2 Optional LCD/Keypad Front Panel3.2 Using the Optional LCD/Keypad Front Panel SHIFTENTER BASIC FUNCTION LABEL PRESET Basic FunctionBASIC FUNCTION COMM SETUP BASIC FUNCTION PRINT METHODADVANCED SETUP COUNTERS Advanced SetupBASIC FUNCTION TOF ADJUST ADVANCED SETUP DATE/TIMEADVANCED SETUP COMMUNICATIONS ADVANCED SETUP SYSTEM OPTIONSADVANCED SETUP OPERATION 28 SELECTIONSADVANCED SETUP MAINTENANCE ADVANCED SETUP MODULESInitiates test see Self-Test, Section Power On Self-Test 3.3 Self-TestFigure 3-3 Self-Test Plugs 3.3.1 Test Label Examples Figure 3-4 Configuration Test LabelGood test label indicates Printhead is operating normally Streaks in test label indicate a dirty or faulty PrintheadSee Chapter 3 for cleaning and replacement Figure 3-5 Printhead Test Label3.3.2 Configuration Test Label Table 3-1 Internal Dip Switch SettingsTemp − this reading is the feedback voltage of the printhead thermistor. At power up or in an idle condition, this value should be in the range of 060 to 065. A reading of 175 is high and could 3.3.3 Character Dump Mode Figure 3-5 ASCII Character Dump Label3.4 Factory Default Setup 3.5 Fuse ReplacementFigure 3-6 Fuse Replacement Using Your Printer Printing Labels 4.0 Introduction4.1 Programming Commands Table 4-2 Immediate CommandsTable 4-1 Attention Getters Description Table 4-3 System Level CommandsChar FormatDescription Table 4-3 System Level Commands ContinuedChar FormatFormat Table 4-4 Label Formatting CommandsDescription nnnnFormat Table 4-4 Label Formatting Commands ContinuedDescription +piiTable 4-5 Special Label Formatting Commands Table 4-6 Bitmapped Font Loading Commands10K OHM 1/4 WATT 4.2 Programming Example4.3 Printing Bar Codes Figure 4-1 Sample LabelField DESCRIPTIONFigure 4-2 Example line Figure 4-3 Example line 4.4 Printing Lines and Boxes Maintenance and Adjustments 5.1 Printer Maintenance schedules5.0 Introduction 5.1.1 Cleaning the Printhead Figure 5-1 Cleaning the Printhead Maintenance and Adjustments5.2 Troubleshooting 2 The Printer does not print Possible cause and solution4 Uneven printing or print too light Possible cause and solution 5 Poor print quality Possible cause and solution3 The media slips or does not properly advance LCD Display 5.2.1 Optional LCD/Keypad Front Panel AlarmsAlarm Description PROM FAULTCUTTER FAULT 5.3 Mechanical AdjustmentsAlarm Description RIB SAVER FAULT5.3.1 Media Width Adjustment Figure 5-2 Media Width Adjustment5.3.2 Media Sensor Adjustment Figure 5-3 Media Sensor Adjustment5.3.3 Printhead Replacement RemovalFigure 5-4 Configuration Test Label Replacement Figure 5-5 Printhead RemovalMaintenance and Adjustments Char Appendix A ASCII Control Code ChartChar CharChar NOTE For the hardware handshake XON/XOFF commands XON = DC1XOFF = DC3ASCII Control Code Chart CharAppendix B Available Fonts and Bar Codes Charac. Per Inch B.1 Human-Readable FontsFont Matrix Sizes Font0 - Identifies a 96-character alphanumeric font alphanumeric uppercase font 6 - Identifies a 62-character7 - Identifies a font that prints OCR A, sizeFont Bar Code FontsTable B-3 Valid Bar Code Font ASCII Characters Bar CodeAppendix B Barcode O Appendix BBarcode S Barcode T Barcode z Appendix BLower case “c” Error CodesAppendix C Lower case eAppendix C How to reach us Support ServicesAppendix D Technical Support Service via TelephoneSerial Number Model Number W.H. Brady Company Customer Service FormComplete this form before requesting technical assistance Address City State, Zip Phone Contact Hours available for return callProduct Service and Support Programs Appendix D Appendix E Warranty Information Brady Limited Warranty Statement Bradyprinter THT Model PrinterThermal Printhead Warranty Service Procedures General Warranty ProvisionsLimitation of Liability Appendix E