Symptom | Probable Cause | Remedy | Reference |
|
|
|
|
|
|
| The thread is tangled, for example, | Remove the tangled thread. If the |
|
|
| thread is tangled in the bobbin case, | page 70 |
| |
| in the bobbin case. |
| ||
| clean the race. |
|
| |
|
|
|
| |
|
|
|
|
|
| The needle is bent or blunt. | Replace the needle. | page 35 |
|
|
|
|
| |
| The needle is incorrectly installed. | Correctly install the needle. |
| |
|
|
| ||
|
|
|
|
|
| The area around the hole in the | Replace the needle plate. Contact |
|
|
| needle plate is scratched, or has a | your retailer or the nearest authorized | – |
|
The upper thread | burr on it. | service center. |
|
|
|
|
|
| |
The area around the hole in the | Replace the embroidery foot. Contact |
|
| |
breaks. |
|
| ||
| embroidery foot is scratched, or | your retailer or the nearest authorized | – |
|
| has a burr on it. | service center. |
|
|
|
|
|
| 3 |
| The bobbin case is scratched, or | Replace the bobbin case. Contact |
| |
| your retailer or the nearest authorized | – | ||
| has a burr on it. | |||
| service center. |
|
| |
|
|
|
| |
|
|
|
|
|
|
| Incorrect bobbins will not work |
|
|
| A bobbin designed specifically for | properly. Only use a bobbin | page 24 |
|
| this machine is not used. | designed specifically for this |
| |
|
|
| ||
|
| machine. |
|
|
|
|
|
|
|
Bobbin thread | The thread that was pulled out | Wind the thread that was pulled off |
|
|
does not wind |
|
| ||
was not wound onto the bobbin | around the bobbin five or six times | page 26 |
| |
neatly on the |
| |||
correctly. | clockwise. |
|
| |
bobbin. |
|
| ||
|
|
|
| |
|
|
|
|
|
| The bobbin thread is incorrectly | Correctly install the bobbin thread. | page 28 |
|
| installed. |
| ||
|
|
|
| |
|
|
|
|
|
| The bobbin is scratched or does |
|
|
|
| not rotate smoothly, or has a burr | Replace the bobbin. | – |
|
The lower thread | on it. |
|
|
|
|
|
|
| |
is tangled or | The thread is tangled. | Remove the tangled thread and clean | page 70 |
|
breaks. |
| |||
the race. |
| |||
|
|
|
| |
|
|
|
|
|
| A bobbin designed specifically for | Incorrect bobbins will not work |
|
|
| properly. Only use a bobbin | page 24 |
| |
| this machine is not used. | designed specifically for this |
| |
|
|
| ||
|
| machine. |
|
|
|
|
|
|
|
| The upper thread was not | Correct the upper threading. | page 30 |
|
| threaded correctly. |
| ||
|
|
|
| |
|
|
|
|
|
| The bobbin thread is incorrectly | Correctly install the bobbin thread. | page 28 |
|
| installed. |
| ||
|
|
|
| |
The thread tension |
|
|
|
|
The thread tension is incorrect. | Adjust the tension of the upper | page 64 |
| |
is incorrect. |
| |||
thread. |
| |||
|
|
|
| |
|
|
|
|
|
|
| Incorrect bobbins will not work |
|
|
| A bobbin designed specifically for | properly. Only use a bobbin | page 24 |
|
| this machine is not used. | designed specifically for this |
| |
|
|
| ||
|
| machine. |
|
|
|
|
|
|
|
