Removing the needle plate | Brother Sewing Machines specs

Removing the needle plate

————————————————————————————————————————————————————

hInsert the bobbin case so that the projection on the bobbin case aligns with the spring.

a

b

a

b

aProjection

bSpring

iInsert the tabs on the needle plate cover into the needle plate, and then slide the cover back on.

a

aNeedle plate cover

jInstallposition.the flat bed attachment in its original

CAUTION

●Never use a bobbin case that is scratched, otherwise the upper thread may become tangled, the needle may break or sewing performance may suffer. For a new bobbin case (part code: XC3153-151), contact your nearest authorized service center.

●Be sure that the bobbin case is correctly installed, otherwise the needle may break.

Removing the needle plate

When the thread is tangled and cannot be removed by cleaning the race, remove the needle plate.

aFollow steps a through f on page 126.

bRemove the needle plate by removing the screws with the included screwdriver.

Remove the tangled thread from the needle
cplate.
Return the needle plate to its original position,	4
dand then tighten the screws with the included

screwdriver.

Note

zAlign the two screw holes on the needle plate with the two holes on the machine.

eFollow steps g through j (page 126-127).

Care and Maintenance 127

Image 128

Brother Sewing Machines operation manual Removing the needle plate, Care and Maintenance

Contents

Operation Manual GETTING READY SEWING BASICSUTILITY STITCHES APPENDIX Computerized Sewing Machine Important Safety Instructions 7 For a longer service life 8 For repair or adjustment FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY FOR USERS IN AUSTRALIA AND NEW ZEALAND SEWING BASICS ContentsGETTING READY UTILITY STITCHES APPENDIX Stitch SettingsCare and Maintenance Troubleshooting Sewing Machine Features Introductiona Easy upper threading b One-touch lower threading Accessories AccessoriesIncluded accessories Memo Optional accessoriesThe following are available as optional accessories Names of Machine Parts and Their Functions Names of Machine Parts and Their FunctionsMachine Needle and presser foot section Operation buttons @ A C Operation panelStitch mode keys h-j Page 1 GETTING READY Power supply precautions When you are away from the machine After using the machineWhen the power fails during use Use only the power cord included with this machine Turning the Machine On/Off Turning on the machineTurning off the machine Understanding the LCD Screens a Presser foot that should be used b Stitch modec Twin needle/needle stop position d Automatic reverse/reinforcement stitches e Selected stitch Changing the Machine Settings Changing the settingsVarious sewing machine operations and sewing settings can be changed Changing the Machine Settings List of stitch or machine attributes AttributeIcon Details Adjusting the brightness of the LCD Winding/Installing the Bobbin Bobbin precautionsWinding the bobbin Actual size a Spool pin b Spool cap Winding/Installing the Bobbina Notch b Bobbin winder shaft spring If the spool net is too long, fold it to fit the size of the spool mPress start/stop button once Installing the bobbin hReattach the bobbin cover Upper Threading Threading the upper thread Upper Threading Memo Threading the needle X The thread is passed through the eye of the needle Using the twin needle Threading the needle manually without using the needle threader dInsert the extra spool pin into the end of the bobbin winder shaft When changing the sewing direction fReattach the bobbin cover Pulling up the bobbin threada Insert the bobbin into the bobbin case Replacing the Needle Needle precautionsReplacing the Needle Thread Needle types and their usesWeight machine starts sewing Checking the needleReplacing the needle a Needle stopper Install the twin needle in the same waya Needle clamp screw b Screwdriver Presser foot precautions Replacing the Presser FootReplacing the presser foot The presser foot presses down on the fabric d Press the black button at the back of the presser foot holder Removing the presser foot holder Using the optional walking foot eAttach the presser foot holder Sewing large pieces of fabric Sewing Cylindrical or Large PiecesStitching cylindrical pieces Sewing Cylindrical or Large Pieces GETTING READY Adjusting the stitch width Adjusting the stitch lengthSEWING BASICS The necessary preparations for sewing are described in this chapter General sewing procedure Sewing Positioning the fabric Sewing Starting to sew Using the operation buttonsUsing the foot controller bPress start/stop button once cTurn on the sewing machine Securing the stitching ePress start/stop button, or press down on the foot controller Cutting the thread Changing the tension of the upper thread Adjusting the Thread TensionAdjusting the Thread Tension Adjusting the Stitch Width and Length Adjusting the stitch width Adjusting the stitch length Adjusting the Stitch Width and Length Useful Functions Changing the needle stop positionFunctions useful in improving sewing efficiency are described below Automatically sewing reverse/ reinforcement stitches Useful Functions dPosition the fabric under the presser foot, andthen press start/stop button once once Useful Sewing Tips Trial sewingChanging the sewing direction Sewing curves Sewing thin fabrics Sewing stretch fabricsUseful Sewing Tips foot will return to its normal position Sewing an even seam allowance Aligning the fabric with the presser foot using overcasting foot “G” using the optional side cutterSatin stitching using the sewing 3 UTILITY STITCHES Preset utility stitch Selecting StitchingSelecting stitch types and patterns Selecting stitching † Character stitches No.01-55† Utility decorative stitches No.01-62 Selecting Stitching With direct selection With number selectionPreset utility stitch Saved patterns To select a different stitch † To select a stitch in a different mode as the current one Overcasting Stitches Sewing overcasting stitches using overcasting foot “G”Overcasting Stitches 3-point Sewing overcasting stitches using zigzag foot “J”2-point Sewing overcasting stitches using the optional side cutter a Remove the presser footb Lower the presser foot lever, and then manually thread the needle c Raise the presser foot lever hSelect a stitch jPosition the fabric in the side cutterkLowersewing.the presser foot lever, and then start a 2 cm 3/4 inch Basic Stitching Basic StitchingBasic stitching Changing the needle position 3 4 5For details, refer to “Adjusting the stitch width” page Blind Hem Stitching Sew a blind hem according to the following procedureBlind Hem Stitching If the needle catches too much of the hem fold Buttonhole Stitching/Button Sewing Buttonhole Stitching/Button Sewing Buttonhole sewing If the button does not fit in the button guide plate cAttach buttonhole foot “A”dSelect a stitch fPullpossible.down the buttonhole lever as far as Do not use the seam ripper in any other way than how it is intended Changing the stitch width Adjust the stitch width Button sewing kWhen you are finished attaching the button A zipper can be sewn in place Zipper InsertionInserting a centered zipper Zipper Insertion Inserting a side zipper b Bastefabric.the two pieces up to the edge of the hAttach the presser foot holder to the right pin of zipper foot “I” o Remove the basting stitching Sewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching Stretch fabrics can be sewn and elastic tape can be attached dAttach zigzag foot “J” Appliqué, Patchwork and Quilt Stitching Appliqué, Patchwork and Quilt Stitching Appliqué stitching a 6.5 mm 1/4 inch Patchwork crazy quilt stitchingPiecing Quilting bholder Free-motion quiltingaTurn off the sewing machine Satin stitching using the sewing speed controller gPresskey. OK key or Cancel/clear fPress. or Stitch width keys to selecthSelect stitch a Narrower b Wider Bar tack stitching Reinforcement StitchingTriple stretch stitching Reinforcement Stitching Eyelet Stitching Decorative Stitching Decorative StitchingVarious decorative stitches can be sewn with this sewing machine Fagoting of the upper thread” page Scallop stitchingSmocking Shell tuck stitching Joining Heirloom stitchinga Wrong side of fabric b 6.5 mm 1/4 inch seam allowance c Straight stitch UTILITY STITCHES a 4 mm 3/16 inch Sewing patterns Sewing the Various Built-In Decorative PatternsSewing beautiful patterns aSelect the first pattern Combining patternsSewing the Various Built-In Decorative Patterns a Single b Repeated Repeat sewing patternsChecking the selected pattern Mirror imaging the pattern dPresskey. OK key or Cancel/clearaSelect a stitch bPress Saving patterns a Normal b Mirror-imaged Retrieving a pattern Realigning the pattern hPress or Stitch width keys UTILITY STITCHES 4 APPENDIX Stitch Settings Utility stitchesAPPENDIX Left Stitch Settings Stitch Name Rick-rack stitch Decorative stitch Serpentine stitch Hem stitching Hem stitching Buttonhole stitch Walking Foot Presser FootTwin Needle Other stitches APPENDIX Left/Right Flipping 1 Pattern for making adjustment2 Use monogramming foot “N” when combined with other pattern Care and Maintenance Cleaning the machine surfaceCleaning the race Simple sewing machine maintenance operations are described below Care and Maintenance Removing the needle plate Troubleshooting Troubleshooting The upper threadbreaks The lower thread is skipped The thread tensionis incorrect The fabric is the LCD Error messages Troubleshooting Cancelling the operation beep Nothing appears in the LCDOperation beep For a correct operation One beep is sounded ePress Cancel/clear key or OK key Numerics Index Index utility decorative stitches English 885-V14 XE2408-0012 Printed in China