Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07045, A07044 installation instructions Unit Damage Hazard

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 11

UNIT DAMAGE HAZARD

!CAUTION

UNIT DAMAGE HAZARD

Failure to follow this caution may result in equipment damage or improper operation.

Improper wiring or installation may damage Thermidistat Control. Check to make sure wiring is correct before proceeding with installation or turning on power.

1.Turn off all power to equipment.

2.If an existing Thermidistat Control is being replaced

a.Remove existing control from wall.

b.Disconnect wires from existing control, 1 at a time.

c.As each wire is disconnected, record wire color and terminal marking.

d.New or additional wire may be needed to accommodate added hu- midity outputs.

e.Discard or recycle old control.

11

Image 11

Bryant A07045, A07044 installation instructions Unit Damage Hazard

Contents

Non---ProgrammableControl Installation InstructionsT6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTAT Programmable ControlSAFETY CONSIDERATIONS TABLE OF CONTENTSINTRODUCTION Power INSTALLATION CONSIDERATIONSFig. 1 - PCB Breakout Jumper ModelsHumidify Equipment and Connections ELECTRICAL OPERATION HAZARD Dehumidify Equipment and ConnectionsOutdoor Temperature Sensor Remote Indoor Temperature Sensor Two-PieceThermidistat ConfigurationFig. 2 - T6-PRHCarton Contents INSTALLATIONThermidistat Control Location Fig. 3 - T6-NRHCarton ContentsELECTRICAL OPERATION HAZARD Install Thermidistat ControlUNIT DAMAGE HAZARD ENVIRONMENTAL HAZARD Two-PieceInstallationA07226 Fig. 4 - Press Tabs to Remove BackplateFig. 5 - Take Apart A07225Fig. 6 - Backplate Mounting Relays Fig. 7 - Control Module Wiring GuideA07167 Fig. 8 - Secure Wires to Terminal StripFig. 9 - Connect Pigtail Wires to Display Module A07166Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Humidity Offset Adjustment Adjustable Setpoint Deadband not available onSmart Recovery programmable models only Room Temperature Offset AdjustmentOption 01 — Equipment Type Configuration Options -SelectionOption 04 — Fan G On With W/W1 Option 02 - Clean Filter TimerOption 03 — Fahrenheit/Centigrade Option 08 - Auxiliary Heat Lockout Temperature Option 06 - Cooling Lockout Below 55 FOption 07 - Zoning Option 10 - Reversing Valve Option 09 - Heat Pump Lockout TemperatureOption 14 — Humidity Display Offset Adjust Option 11 — Deadband Setting Between Heat & CoolOption 12 — Smart Recovery Option 13 — Room Air Temperature Offset AdjustOption 17 — Time Between Equipment Stages Option 16 — Maximum Cycles Per HourOption 18 - Backlight Configuration Default is OF off Default is OF off Option 23 — High Heat Latch Temperature Option 22 — High Cool Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 29 - Humidifier Pad Reminder Option 27 — Maximum Heating SetpointOption 28 - UV Light Reminder Default is OF off Option 99 — Reset to Factory Defaults Option 33 — Single or Two-PieceInstallationSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidification Humidity Control FeaturesTo Select Humidification programmable Table 2 - Humidification SelectionsAdditional Humidify Comments DehumidificationTo Select Humidification non-programmable 2.Cool to Dehumidify 1.Normal Dehumidify Operation3.Dehumidify Off Fig. 16 - Auto HumidityDehumidify Output and Equipment Connections Additional Dehumidify CommentsVacation programmable models only Vacation Dehumidification Table 3 – Vacation Setpoints Default ValuesVacation Setpoints Vacation HumidificationOPERATIONAL INFORMATION TimersCycle Timer Ten-MinuteStaging TimerHeat/Cool Setpoints Desired Temperature Equipment On IndicatorsThree-MinuteMinimum on Time Programmable Fan programmable models only Humidify and Dehumidify IndicatorsAuto Changeover Emergency Heat ModeError Codes TROUBLESHOOTINGE2 - There is no E2 error message COOL Table 4 - Equipment Configuration OutputsEQUIPMENT COOLCOOL Table 4 - Equipment Configuration Outputs contEQUIPMENT COOLA07164 WIRING DIAGRAMSA06573 Fig. 18 - FV/FK Fan Coil w/2-StageHeat PumpA06574 Fig. 19 - Typical Fan Coil w/Heat PumpA06575 A06576 Fig. 21 - FV/FK Fan Coil w/2-StageAir ConditionerA06577 Fig. 22 - Typical Fan Coil w/Air ConditionerA06578 A06579 Fig. 24 - FV/FK Fan Coil w/1-StageHeat PumpA06580 Fig. 25 - Typical Fan Coil Heating OnlyPage A06582 Fig. 27 - FV/FK Fan Coil w/1-StageAir ConditionerA06583 Fig. 28 - Typical Fan Coil Cooling OnlyA06584 A006585 Fig. 30 - Single-StageFurnace w/Heat PumpA06586 A06587 Fig. 32 - Single-StageFurnace w/Air ConditionerA06588 A06589 Fig. 34 - Single-StageFurnace Heating OnlyA06590 Air ConditionerA07760 C. Home, Away, Sleep Settings THERMIDISTAT CONFIGURATION RECORDA. Hardware Configuration B. Mode SettingsE. Configuration Options Catalog No: IIT6---PRH---02 E. Configuration Options cont