Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07045, A07044 installation instructions E2 - There is no E2 error message

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 55

seconds. The control will operate from the temperature sensed by the working sensor.

E1 - If the Display Module and the Equipment Control Module cannot communicate via two-wire connection, an E1 will be displayed.

E2 - There is no E2 error message.

E3 - If Thermidistat Control cannot properly read outdoor temperature, and it is needed for proper operation, display will indicate “--” in the outdoor temperature location.

E4 - If Thermidistat Control’s internal memory fails, E4 will be displayed. Replace Thermidistat Control.

E5 - If Thermidistat Control cannot properly read humidity, E5 will be displayed. Replace Thermidistat Control. If both Humidify and Dehumidify have been set to OF, the humidity value will be shown as “--” when viewed from the humidity menu, but no E5 will be shown in the display.

Table 4 can be used as a troubleshooting tool for determining which outputs will be active for a particular configuration and each operating mode.

55

Image 55

Bryant A07045, A07044 installation instructions E2 - There is no E2 error message

Contents

Non---ProgrammableControl Installation InstructionsT6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTAT Programmable ControlSAFETY CONSIDERATIONS TABLE OF CONTENTSINTRODUCTION Power INSTALLATION CONSIDERATIONSHumidify Equipment and Connections ModelsFig. 1 - PCB Breakout Jumper Dehumidify Equipment and Connections Outdoor Temperature SensorELECTRICAL OPERATION HAZARD Two-PieceThermidistat Configuration Remote Indoor Temperature SensorFig. 2 - T6-PRHCarton Contents INSTALLATIONThermidistat Control Location Fig. 3 - T6-NRHCarton ContentsELECTRICAL OPERATION HAZARD Install Thermidistat ControlUNIT DAMAGE HAZARD ENVIRONMENTAL HAZARD Two-PieceInstallationA07226 Fig. 4 - Press Tabs to Remove BackplateFig. 5 - Take Apart A07225Fig. 6 - Backplate Mounting Relays Fig. 7 - Control Module Wiring GuideA07167 Fig. 8 - Secure Wires to Terminal StripFig. 9 - Connect Pigtail Wires to Display Module A07166Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Humidity Offset Adjustment Adjustable Setpoint Deadband not available onSmart Recovery programmable models only Room Temperature Offset AdjustmentOption 01 — Equipment Type Configuration Options -SelectionOption 03 — Fahrenheit/Centigrade Option 02 — Clean Filter TimerOption 04 — Fan G On With W/W1 Option 06 - Cooling Lockout Below 55 F Option 08 - Auxiliary Heat Lockout TemperatureOption 07 - Zoning Option 10 - Reversing Valve Option 09 - Heat Pump Lockout TemperatureOption 14 — Humidity Display Offset Adjust Option 11 — Deadband Setting Between Heat & CoolOption 12 — Smart Recovery Option 13 — Room Air Temperature Offset AdjustOption 17 — Time Between Equipment Stages Option 16 — Maximum Cycles Per HourOption 18 - Backlight Configuration Default is OF off Default is OF off Option 23 — High Heat Latch Temperature Option 22 — High Cool Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 28 - UV Light Reminder Option 27 — Maximum Heating SetpointOption 29 - Humidifier Pad Reminder Default is OF off Option 99 — Reset to Factory Defaults Option 33 — Single or Two-PieceInstallationSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidification Humidity Control FeaturesTo Select Humidification programmable Table 2 - Humidification SelectionsTo Select Humidification non-programmable DehumidificationAdditional Humidify Comments 2.Cool to Dehumidify 1.Normal Dehumidify Operation3.Dehumidify Off Fig. 16 - Auto HumidityDehumidify Output and Equipment Connections Additional Dehumidify CommentsVacation programmable models only Vacation Dehumidification Table 3 – Vacation Setpoints Default ValuesVacation Setpoints Vacation HumidificationOPERATIONAL INFORMATION TimersCycle Timer Ten-MinuteStaging TimerHeat/Cool Setpoints Desired Temperature Equipment On IndicatorsThree-MinuteMinimum on Time Programmable Fan programmable models only Humidify and Dehumidify IndicatorsAuto Changeover Emergency Heat ModeError Codes TROUBLESHOOTINGE2 - There is no E2 error message COOL Table 4 - Equipment Configuration OutputsEQUIPMENT COOLCOOL Table 4 - Equipment Configuration Outputs contEQUIPMENT COOLA07164 WIRING DIAGRAMSA06573 Fig. 18 - FV/FK Fan Coil w/2-StageHeat PumpA06574 Fig. 19 - Typical Fan Coil w/Heat PumpA06575 A06576 Fig. 21 - FV/FK Fan Coil w/2-StageAir ConditionerA06577 Fig. 22 - Typical Fan Coil w/Air ConditionerA06578 A06579 Fig. 24 - FV/FK Fan Coil w/1-StageHeat PumpA06580 Fig. 25 - Typical Fan Coil Heating OnlyPage A06582 Fig. 27 - FV/FK Fan Coil w/1-StageAir ConditionerA06583 Fig. 28 - Typical Fan Coil Cooling OnlyA06584 A006585 Fig. 30 - Single-StageFurnace w/Heat PumpA06586 A06587 Fig. 32 - Single-StageFurnace w/Air ConditionerA06588 A06589 Fig. 34 - Single-StageFurnace Heating OnlyA06590 Air ConditionerA07760 C. Home, Away, Sleep Settings THERMIDISTAT CONFIGURATION RECORDA. Hardware Configuration B. Mode SettingsE. Configuration Options Catalog No: IIT6---PRH---02 E. Configuration Options cont