Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07044, A07045 Additional Dehumidify Comments, Dehumidify Output and Equipment Connections

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 48

system is in AUTO mode, dehumidify options are available if the last system operation was a call for cooling.

To Select Dehumidification (non-programmable - between NORMAL, COOL TO, and OFF)

Press the features button three times. The first press displays the outdoor air temperature, the second press displays the humidify options and the third press will display the current dehumidify selections.

The mode button is used to cycle through the dehumdify selections.

Additional Dehumidify Comments

Dehumidification can be enhanced (with some efficiency loss) by turning blower off immediately at the end of each cooling cycle (eliminating normal 90 sec blower off delay). Where maximum humidity removal is desired, this should be done. Fan coils have the capability of removing this off delay. On FK or FV Fan Coils, set delay tap to 0/0. On standard fan coils, a jumper can be cut to disable off delay. Refer to fan coil Installation Instructions for details. If FAN is set for continuous operation (fan On icon displayed), G output is turned off for 5 minutes at the end of each cooling cycle as long as dehumidify demand exists.

Like humidify, dehumidify actions are initiated when humidity is 1% above setpoint and are terminated when humidity drops to 1% below setpoint. This prevents unnecessary toggling of dehumidify actions when humidity is near setpoint.

Dehumidify Output and Equipment Connections

When there is a dehumidify demand, dry contact is activated, meaning that a 24VAC signal is removed from the DHUM output terminal. In other words, dehumidify output logic is reversed - output is turned On when no dehumidify demand exists and is turned OFF when demand exists.

48

Image 48

Bryant A07044, A07045 installation instructions Additional Dehumidify Comments, Dehumidify Output and Equipment Connections

Contents

Installation Instructions T6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTATProgrammable Control Non---ProgrammableControlTABLE OF CONTENTS SAFETY CONSIDERATIONSINTRODUCTION INSTALLATION CONSIDERATIONS PowerModels Humidify Equipment and ConnectionsFig. 1 - PCB Breakout Jumper Dehumidify Equipment and Connections Outdoor Temperature SensorELECTRICAL OPERATION HAZARD Two-PieceThermidistat Configuration Remote Indoor Temperature SensorINSTALLATION Fig. 2 - T6-PRHCarton ContentsFig. 3 - T6-NRHCarton Contents Thermidistat Control LocationInstall Thermidistat Control ELECTRICAL OPERATION HAZARDUNIT DAMAGE HAZARD Two-PieceInstallation ENVIRONMENTAL HAZARDFig. 4 - Press Tabs to Remove Backplate Fig. 5 - Take ApartA07225 A07226Fig. 6 - Backplate Mounting Fig. 7 - Control Module Wiring Guide RelaysFig. 8 - Secure Wires to Terminal Strip Fig. 9 - Connect Pigtail Wires to Display ModuleA07166 A07167Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Adjustable Setpoint Deadband not available on Smart Recovery programmable models onlyRoom Temperature Offset Adjustment Humidity Offset AdjustmentConfiguration Options -Selection Option 01 — Equipment TypeOption 02 - Clean Filter Timer Option 03 — Fahrenheit/CentigradeOption 04 — Fan G On With W/W1 Option 06 - Cooling Lockout Below 55 F Option 07 - ZoningOption 08 - Auxiliary Heat Lockout Temperature Option 09 - Heat Pump Lockout Temperature Option 10 - Reversing ValveOption 11 — Deadband Setting Between Heat & Cool Option 12 — Smart RecoveryOption 13 — Room Air Temperature Offset Adjust Option 14 — Humidity Display Offset AdjustOption 16 — Maximum Cycles Per Hour Option 17 — Time Between Equipment StagesOption 18 - Backlight Configuration Default is OF off Default is OF off Option 22 — High Cool Latch Temperature Option 23 — High Heat Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 27 — Maximum Heating Setpoint Option 28 - UV Light ReminderOption 29 - Humidifier Pad Reminder Default is OF off Option 33 — Single or Two-PieceInstallation Option 99 — Reset to Factory DefaultsSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidity Control Features HumidificationTable 2 - Humidification Selections To Select Humidification programmableDehumidification To Select Humidification non-programmableAdditional Humidify Comments 1.Normal Dehumidify Operation 2.Cool to DehumidifyFig. 16 - Auto Humidity 3.Dehumidify OffAdditional Dehumidify Comments Dehumidify Output and Equipment ConnectionsVacation programmable models only Table 3 – Vacation Setpoints Default Values Vacation SetpointsVacation Humidification Vacation DehumidificationTimers Cycle TimerTen-MinuteStaging Timer OPERATIONAL INFORMATIONEquipment On Indicators Three-MinuteMinimum on TimeHeat/Cool Setpoints Desired Temperature Humidify and Dehumidify Indicators Auto ChangeoverEmergency Heat Mode Programmable Fan programmable models onlyTROUBLESHOOTING Error CodesE2 - There is no E2 error message Table 4 - Equipment Configuration Outputs EQUIPMENTCOOL COOLTable 4 - Equipment Configuration Outputs cont EQUIPMENTCOOL COOLWIRING DIAGRAMS A07164Fig. 18 - FV/FK Fan Coil w/2-StageHeat Pump A06573Fig. 19 - Typical Fan Coil w/Heat Pump A06574A06575 Fig. 21 - FV/FK Fan Coil w/2-StageAir Conditioner A06576Fig. 22 - Typical Fan Coil w/Air Conditioner A06577A06578 Fig. 24 - FV/FK Fan Coil w/1-StageHeat Pump A06579Fig. 25 - Typical Fan Coil Heating Only A06580Page Fig. 27 - FV/FK Fan Coil w/1-StageAir Conditioner A06582Fig. 28 - Typical Fan Coil Cooling Only A06583A06584 Fig. 30 - Single-StageFurnace w/Heat Pump A006585A06586 Fig. 32 - Single-StageFurnace w/Air Conditioner A06587A06588 Fig. 34 - Single-StageFurnace Heating Only A06589Air Conditioner A06590A07760 THERMIDISTAT CONFIGURATION RECORD A. Hardware ConfigurationB. Mode Settings C. Home, Away, Sleep SettingsE. Configuration Options E. Configuration Options cont Catalog No: IIT6---PRH---02