Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07045, A07044 Option 27 — Maximum Heating Setpoint, Option 28 - UV Light Reminder

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 37

Option 27 — Maximum Heating Setpoint

This selection allows the installer to configure the maximum heating setpoint. The range is based on the adjustable deadband value Option 11, such that the minimum of the range is 50_F and the maximum is 90_F minus the deadband.

Default is 88_F (based on the adjustable deadband default = 2).

Option 28 — UV Light Reminder

This selection allows the installer to select the number of months after which the UV Light icon will be displayed to indicate to the homeowner that it is time to call the dealer to have the UV Lights replaced. Selections available are OF (off), 6, 12, 18, 24, 30, 36, 42, 48.

OF (off) — The UV Light reminder is turned off and will never be displayed.

6-48 — The number of months after which the UV Light reminder will be displayed, “CHECK UV LIGHT”.

Default is OF (off).

Option 29 — Humidifier Pad Reminder

This selects the number of months after which the Humidifier Pad Reminder icon will be displayed. This is not based on run time.

OF (off) — The Humidifier Pad Reminder is disabled and will never be displayed.

1-24 — The number of months after which the Humidifier Pad Reminder icon will be displayed, “CHECK HUM PAD”.

Default is OF (off).

37

Image 37

Bryant A07045 Option 27 — Maximum Heating Setpoint, Option 28 - UV Light Reminder, Option 29 - Humidifier Pad Reminder

Contents

T6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTAT Installation InstructionsProgrammable Control Non---ProgrammableControlSAFETY CONSIDERATIONS TABLE OF CONTENTSINTRODUCTION Power INSTALLATION CONSIDERATIONSHumidify Equipment and Connections ModelsFig. 1 - PCB Breakout Jumper Outdoor Temperature Sensor Dehumidify Equipment and ConnectionsELECTRICAL OPERATION HAZARD Remote Indoor Temperature Sensor Two-PieceThermidistat ConfigurationFig. 2 - T6-PRHCarton Contents INSTALLATIONThermidistat Control Location Fig. 3 - T6-NRHCarton ContentsELECTRICAL OPERATION HAZARD Install Thermidistat ControlUNIT DAMAGE HAZARD ENVIRONMENTAL HAZARD Two-PieceInstallationFig. 5 - Take Apart Fig. 4 - Press Tabs to Remove BackplateA07225 A07226Fig. 6 - Backplate Mounting Relays Fig. 7 - Control Module Wiring GuideFig. 9 - Connect Pigtail Wires to Display Module Fig. 8 - Secure Wires to Terminal StripA07166 A07167Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Smart Recovery programmable models only Adjustable Setpoint Deadband not available onRoom Temperature Offset Adjustment Humidity Offset AdjustmentOption 01 — Equipment Type Configuration Options -SelectionOption 03 — Fahrenheit/Centigrade Option 02 - Clean Filter TimerOption 04 — Fan G On With W/W1 Option 07 - Zoning Option 06 - Cooling Lockout Below 55 FOption 08 - Auxiliary Heat Lockout Temperature Option 10 - Reversing Valve Option 09 - Heat Pump Lockout TemperatureOption 12 — Smart Recovery Option 11 — Deadband Setting Between Heat & CoolOption 13 — Room Air Temperature Offset Adjust Option 14 — Humidity Display Offset AdjustOption 17 — Time Between Equipment Stages Option 16 — Maximum Cycles Per HourOption 18 - Backlight Configuration Default is OF off Default is OF off Option 23 — High Heat Latch Temperature Option 22 — High Cool Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 28 - UV Light Reminder Option 27 — Maximum Heating SetpointOption 29 - Humidifier Pad Reminder Default is OF off Option 99 — Reset to Factory Defaults Option 33 — Single or Two-PieceInstallationSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidification Humidity Control FeaturesTo Select Humidification programmable Table 2 - Humidification SelectionsTo Select Humidification non-programmable DehumidificationAdditional Humidify Comments 2.Cool to Dehumidify 1.Normal Dehumidify Operation3.Dehumidify Off Fig. 16 - Auto HumidityDehumidify Output and Equipment Connections Additional Dehumidify CommentsVacation programmable models only Vacation Setpoints Table 3 – Vacation Setpoints Default ValuesVacation Humidification Vacation DehumidificationCycle Timer TimersTen-MinuteStaging Timer OPERATIONAL INFORMATIONThree-MinuteMinimum on Time Equipment On IndicatorsHeat/Cool Setpoints Desired Temperature Auto Changeover Humidify and Dehumidify IndicatorsEmergency Heat Mode Programmable Fan programmable models onlyError Codes TROUBLESHOOTINGE2 - There is no E2 error message EQUIPMENT Table 4 - Equipment Configuration OutputsCOOL COOLEQUIPMENT Table 4 - Equipment Configuration Outputs contCOOL COOLA07164 WIRING DIAGRAMSA06573 Fig. 18 - FV/FK Fan Coil w/2-StageHeat PumpA06574 Fig. 19 - Typical Fan Coil w/Heat PumpA06575 A06576 Fig. 21 - FV/FK Fan Coil w/2-StageAir ConditionerA06577 Fig. 22 - Typical Fan Coil w/Air ConditionerA06578 A06579 Fig. 24 - FV/FK Fan Coil w/1-StageHeat PumpA06580 Fig. 25 - Typical Fan Coil Heating OnlyPage A06582 Fig. 27 - FV/FK Fan Coil w/1-StageAir ConditionerA06583 Fig. 28 - Typical Fan Coil Cooling OnlyA06584 A006585 Fig. 30 - Single-StageFurnace w/Heat PumpA06586 A06587 Fig. 32 - Single-StageFurnace w/Air ConditionerA06588 A06589 Fig. 34 - Single-StageFurnace Heating OnlyA06590 Air ConditionerA07760 A. Hardware Configuration THERMIDISTAT CONFIGURATION RECORDB. Mode Settings C. Home, Away, Sleep SettingsE. Configuration Options Catalog No: IIT6---PRH---02 E. Configuration Options cont