Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07045, A07044 Thermidistat Control Location, T6-NRHCarton Contents

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 9

Fig. 3 - T6-NRH Carton Contents

A07753

Fig. 3 - T6-NRH Carton Contents

1.Display Module

2.Stand-off for Equipment Control Module

3.Outside Air Temperature Sensor, screws and pigtail.

4.Equipment Control Module

Thermidistat Control Location

Thermidistat Control should be mounted:

SApproximately 5 ft (1.5m) from floor.

SClose to or in a frequently used room, preferably on an inside parti- tioning wall.

SOn a section of wall without pipes or duct work. Thermidistat Control should NOT be mounted:

SClose to a window, on an outside wall, or next to a door leading to the outside.

9

Image 9

Bryant A07045, A07044 installation instructions Thermidistat Control Location, T6-NRHCarton Contents

Contents

T6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTAT Installation InstructionsProgrammable Control Non---ProgrammableControlSAFETY CONSIDERATIONS TABLE OF CONTENTSINTRODUCTION Power INSTALLATION CONSIDERATIONSModels Humidify Equipment and ConnectionsFig. 1 - PCB Breakout Jumper Outdoor Temperature Sensor Dehumidify Equipment and ConnectionsELECTRICAL OPERATION HAZARD Two-PieceThermidistat Configuration Remote Indoor Temperature SensorFig. 2 - T6-PRHCarton Contents INSTALLATIONThermidistat Control Location Fig. 3 - T6-NRHCarton ContentsELECTRICAL OPERATION HAZARD Install Thermidistat ControlUNIT DAMAGE HAZARD ENVIRONMENTAL HAZARD Two-PieceInstallationFig. 5 - Take Apart Fig. 4 - Press Tabs to Remove BackplateA07225 A07226Fig. 6 - Backplate Mounting Relays Fig. 7 - Control Module Wiring GuideFig. 9 - Connect Pigtail Wires to Display Module Fig. 8 - Secure Wires to Terminal StripA07166 A07167Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Smart Recovery programmable models only Adjustable Setpoint Deadband not available onRoom Temperature Offset Adjustment Humidity Offset AdjustmentOption 01 — Equipment Type Configuration Options -SelectionOption 02 — Clean Filter Timer Option 03 — Fahrenheit/CentigradeOption 04 — Fan G On With W/W1 Option 08 - Auxiliary Heat Lockout Temperature Option 06 - Cooling Lockout Below 55 FOption 07 - Zoning Option 10 - Reversing Valve Option 09 - Heat Pump Lockout TemperatureOption 12 — Smart Recovery Option 11 — Deadband Setting Between Heat & CoolOption 13 — Room Air Temperature Offset Adjust Option 14 — Humidity Display Offset AdjustOption 17 — Time Between Equipment Stages Option 16 — Maximum Cycles Per HourOption 18 - Backlight Configuration Default is OF off Default is OF off Option 23 — High Heat Latch Temperature Option 22 — High Cool Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 27 — Maximum Heating Setpoint Option 28 - UV Light ReminderOption 29 - Humidifier Pad Reminder Default is OF off Option 99 — Reset to Factory Defaults Option 33 — Single or Two-PieceInstallationSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidification Humidity Control FeaturesTo Select Humidification programmable Table 2 - Humidification SelectionsDehumidification To Select Humidification non-programmableAdditional Humidify Comments 2.Cool to Dehumidify 1.Normal Dehumidify Operation3.Dehumidify Off Fig. 16 - Auto HumidityDehumidify Output and Equipment Connections Additional Dehumidify CommentsVacation programmable models only Vacation Setpoints Table 3 – Vacation Setpoints Default ValuesVacation Humidification Vacation DehumidificationCycle Timer TimersTen-MinuteStaging Timer OPERATIONAL INFORMATIONEquipment On Indicators Heat/Cool Setpoints Desired TemperatureThree-MinuteMinimum on Time Auto Changeover Humidify and Dehumidify IndicatorsEmergency Heat Mode Programmable Fan programmable models onlyError Codes TROUBLESHOOTINGE2 - There is no E2 error message EQUIPMENT Table 4 - Equipment Configuration OutputsCOOL COOLEQUIPMENT Table 4 - Equipment Configuration Outputs contCOOL COOLA07164 WIRING DIAGRAMSA06573 Fig. 18 - FV/FK Fan Coil w/2-StageHeat PumpA06574 Fig. 19 - Typical Fan Coil w/Heat PumpA06575 A06576 Fig. 21 - FV/FK Fan Coil w/2-StageAir ConditionerA06577 Fig. 22 - Typical Fan Coil w/Air ConditionerA06578 A06579 Fig. 24 - FV/FK Fan Coil w/1-StageHeat PumpA06580 Fig. 25 - Typical Fan Coil Heating OnlyPage A06582 Fig. 27 - FV/FK Fan Coil w/1-StageAir ConditionerA06583 Fig. 28 - Typical Fan Coil Cooling OnlyA06584 A006585 Fig. 30 - Single-StageFurnace w/Heat PumpA06586 A06587 Fig. 32 - Single-StageFurnace w/Air ConditionerA06588 A06589 Fig. 34 - Single-StageFurnace Heating OnlyA06590 Air ConditionerA07760 A. Hardware Configuration THERMIDISTAT CONFIGURATION RECORDB. Mode Settings C. Home, Away, Sleep SettingsE. Configuration Options Catalog No: IIT6---PRH---02 E. Configuration Options cont