Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07045, A07044 installation instructions Single-PieceInstallation

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 21

Single-Piece Installation

The following steps should be followed for the installation of the single-piece configuration.

1.Remove cover from Equipment Control Module by pressing the two tabs on the bottom edge and pulling away. Route wires through large hole in Equipment Control Module. Level Equipment Control Module against wall (for aesthetic value only - Equipment Control Module need not be leveled for proper operation) and mark wall through 2 mounting holes.

2.Drill two 3/16-in. mounting holes in wall where marked. Thermidistat Control may be mounted to a standard junction box if desired. Hole pat- tern on Equipment Control Module matches junction box mounting holes.

3.Secure rear plastic Equipment Control Module to wall with 2 screws and anchors provided. Additional mounting holes are available for more se- cure mounting if needed. Make sure all wires extend through hole in Equipment Control Module.

4.Adjust length and routing of each wire to reach proper connector block and terminal on Equipment Control Module with 1/4-in. extra length. See Fig. 14.

21

Image 21

Bryant A07045, A07044 installation instructions Single-PieceInstallation

Contents

T6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTAT Installation InstructionsProgrammable Control Non---ProgrammableControlSAFETY CONSIDERATIONS TABLE OF CONTENTSINTRODUCTION Power INSTALLATION CONSIDERATIONSModels Humidify Equipment and ConnectionsFig. 1 - PCB Breakout Jumper Outdoor Temperature Sensor Dehumidify Equipment and ConnectionsELECTRICAL OPERATION HAZARD Two-PieceThermidistat Configuration Remote Indoor Temperature SensorFig. 2 - T6-PRHCarton Contents INSTALLATIONThermidistat Control Location Fig. 3 - T6-NRHCarton ContentsELECTRICAL OPERATION HAZARD Install Thermidistat ControlUNIT DAMAGE HAZARD ENVIRONMENTAL HAZARD Two-PieceInstallationFig. 5 - Take Apart Fig. 4 - Press Tabs to Remove BackplateA07225 A07226Fig. 6 - Backplate Mounting Relays Fig. 7 - Control Module Wiring GuideFig. 9 - Connect Pigtail Wires to Display Module Fig. 8 - Secure Wires to Terminal StripA07166 A07167Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Smart Recovery programmable models only Adjustable Setpoint Deadband not available onRoom Temperature Offset Adjustment Humidity Offset AdjustmentOption 01 — Equipment Type Configuration Options -SelectionOption 02 — Clean Filter Timer Option 03 — Fahrenheit/CentigradeOption 04 — Fan G On With W/W1 Option 08 - Auxiliary Heat Lockout Temperature Option 06 - Cooling Lockout Below 55 FOption 07 - Zoning Option 10 - Reversing Valve Option 09 - Heat Pump Lockout TemperatureOption 12 — Smart Recovery Option 11 — Deadband Setting Between Heat & CoolOption 13 — Room Air Temperature Offset Adjust Option 14 — Humidity Display Offset AdjustOption 17 — Time Between Equipment Stages Option 16 — Maximum Cycles Per HourOption 18 - Backlight Configuration Default is OF off Default is OF off Option 23 — High Heat Latch Temperature Option 22 — High Cool Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 27 — Maximum Heating Setpoint Option 28 - UV Light ReminderOption 29 - Humidifier Pad Reminder Default is OF off Option 99 — Reset to Factory Defaults Option 33 — Single or Two-PieceInstallationSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidification Humidity Control FeaturesTo Select Humidification programmable Table 2 - Humidification SelectionsDehumidification To Select Humidification non-programmableAdditional Humidify Comments 2.Cool to Dehumidify 1.Normal Dehumidify Operation3.Dehumidify Off Fig. 16 - Auto HumidityDehumidify Output and Equipment Connections Additional Dehumidify CommentsVacation programmable models only Vacation Setpoints Table 3 – Vacation Setpoints Default ValuesVacation Humidification Vacation DehumidificationCycle Timer TimersTen-MinuteStaging Timer OPERATIONAL INFORMATIONEquipment On Indicators Heat/Cool Setpoints Desired TemperatureThree-MinuteMinimum on Time Auto Changeover Humidify and Dehumidify IndicatorsEmergency Heat Mode Programmable Fan programmable models onlyError Codes TROUBLESHOOTINGE2 - There is no E2 error message EQUIPMENT Table 4 - Equipment Configuration OutputsCOOL COOLEQUIPMENT Table 4 - Equipment Configuration Outputs contCOOL COOLA07164 WIRING DIAGRAMSA06573 Fig. 18 - FV/FK Fan Coil w/2-StageHeat PumpA06574 Fig. 19 - Typical Fan Coil w/Heat PumpA06575 A06576 Fig. 21 - FV/FK Fan Coil w/2-StageAir ConditionerA06577 Fig. 22 - Typical Fan Coil w/Air ConditionerA06578 A06579 Fig. 24 - FV/FK Fan Coil w/1-StageHeat PumpA06580 Fig. 25 - Typical Fan Coil Heating OnlyPage A06582 Fig. 27 - FV/FK Fan Coil w/1-StageAir ConditionerA06583 Fig. 28 - Typical Fan Coil Cooling OnlyA06584 A006585 Fig. 30 - Single-StageFurnace w/Heat PumpA06586 A06587 Fig. 32 - Single-StageFurnace w/Air ConditionerA06588 A06589 Fig. 34 - Single-StageFurnace Heating OnlyA06590 Air ConditionerA07760 A. Hardware Configuration THERMIDISTAT CONFIGURATION RECORDB. Mode Settings C. Home, Away, Sleep SettingsE. Configuration Options Catalog No: IIT6---PRH---02 E. Configuration Options cont