Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07045, A07044 Option 09 - Heat Pump Lockout Temperature, Option 10 - Reversing Valve

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 29

OF (off) - function is disabled. Auxiliary heat is allowed to operate whenever sufficient demand for heat is available.

5-55_F - Outdoor temperature above which the auxiliary heat is not allowed to operate (unless MODE is set to Emergency Heat).

Default is OF (off).

Option 09 — Heat Pump Lockout Temperature

This selection is only available on Hybrid Heat systems. A Hybrid Heat system is selected via the Option 1 Equipment Type configuration. Configurations settings are: OF (off), 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55.

OF (off) — the heating cycle will always start with heat pump heating.

5-55_F — the outdoor temperature below which heat pump operation is not allowed.

When emergency heat mode is selected only auxiliary heat will operate. Default is OF (off).

Option 10 — Reversing Valve

This selection is only available on heat pump systems. “O” terminal can be configured to be energized in either heating mode or in cooling mode, depending on heat pump operation. “O” is used to describe a heat pump system that energizes its reversing valve in cooling. “B” is used to describe a heat pump system that energized its reversing valve in heating.

H — Reversing valve output (O/W2/B) is energized when HEAT mode is selected.

C — Reversing valve output (O/W2/B) is energized when COOL mode is selected.

Default is C.

29

Image 29

Bryant A07045, A07044 installation instructions Option 09 - Heat Pump Lockout Temperature, Option 10 - Reversing Valve

Contents

T6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTAT Installation InstructionsProgrammable Control Non---ProgrammableControlSAFETY CONSIDERATIONS TABLE OF CONTENTSINTRODUCTION Power INSTALLATION CONSIDERATIONSFig. 1 - PCB Breakout Jumper ModelsHumidify Equipment and Connections ELECTRICAL OPERATION HAZARD Dehumidify Equipment and ConnectionsOutdoor Temperature Sensor Remote Indoor Temperature Sensor Two-PieceThermidistat ConfigurationFig. 2 - T6-PRHCarton Contents INSTALLATIONThermidistat Control Location Fig. 3 - T6-NRHCarton ContentsELECTRICAL OPERATION HAZARD Install Thermidistat ControlUNIT DAMAGE HAZARD ENVIRONMENTAL HAZARD Two-PieceInstallationFig. 5 - Take Apart Fig. 4 - Press Tabs to Remove BackplateA07225 A07226Fig. 6 - Backplate Mounting Relays Fig. 7 - Control Module Wiring GuideFig. 9 - Connect Pigtail Wires to Display Module Fig. 8 - Secure Wires to Terminal StripA07166 A07167Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Smart Recovery programmable models only Adjustable Setpoint Deadband not available onRoom Temperature Offset Adjustment Humidity Offset AdjustmentOption 01 — Equipment Type Configuration Options -SelectionOption 04 — Fan G On With W/W1 Option 02 - Clean Filter TimerOption 03 — Fahrenheit/Centigrade Option 08 - Auxiliary Heat Lockout Temperature Option 06 - Cooling Lockout Below 55 FOption 07 - Zoning Option 10 - Reversing Valve Option 09 - Heat Pump Lockout TemperatureOption 12 — Smart Recovery Option 11 — Deadband Setting Between Heat & CoolOption 13 — Room Air Temperature Offset Adjust Option 14 — Humidity Display Offset AdjustOption 17 — Time Between Equipment Stages Option 16 — Maximum Cycles Per HourOption 18 - Backlight Configuration Default is OF off Default is OF off Option 23 — High Heat Latch Temperature Option 22 — High Cool Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 29 - Humidifier Pad Reminder Option 27 — Maximum Heating SetpointOption 28 - UV Light Reminder Default is OF off Option 99 — Reset to Factory Defaults Option 33 — Single or Two-PieceInstallationSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidification Humidity Control FeaturesTo Select Humidification programmable Table 2 - Humidification SelectionsAdditional Humidify Comments DehumidificationTo Select Humidification non-programmable 2.Cool to Dehumidify 1.Normal Dehumidify Operation3.Dehumidify Off Fig. 16 - Auto HumidityDehumidify Output and Equipment Connections Additional Dehumidify CommentsVacation programmable models only Vacation Setpoints Table 3 – Vacation Setpoints Default ValuesVacation Humidification Vacation DehumidificationCycle Timer TimersTen-MinuteStaging Timer OPERATIONAL INFORMATIONHeat/Cool Setpoints Desired Temperature Equipment On IndicatorsThree-MinuteMinimum on Time Auto Changeover Humidify and Dehumidify IndicatorsEmergency Heat Mode Programmable Fan programmable models onlyError Codes TROUBLESHOOTINGE2 - There is no E2 error message EQUIPMENT Table 4 - Equipment Configuration OutputsCOOL COOLEQUIPMENT Table 4 - Equipment Configuration Outputs contCOOL COOLA07164 WIRING DIAGRAMSA06573 Fig. 18 - FV/FK Fan Coil w/2-StageHeat PumpA06574 Fig. 19 - Typical Fan Coil w/Heat PumpA06575 A06576 Fig. 21 - FV/FK Fan Coil w/2-StageAir ConditionerA06577 Fig. 22 - Typical Fan Coil w/Air ConditionerA06578 A06579 Fig. 24 - FV/FK Fan Coil w/1-StageHeat PumpA06580 Fig. 25 - Typical Fan Coil Heating OnlyPage A06582 Fig. 27 - FV/FK Fan Coil w/1-StageAir ConditionerA06583 Fig. 28 - Typical Fan Coil Cooling OnlyA06584 A006585 Fig. 30 - Single-StageFurnace w/Heat PumpA06586 A06587 Fig. 32 - Single-StageFurnace w/Air ConditionerA06588 A06589 Fig. 34 - Single-StageFurnace Heating OnlyA06590 Air ConditionerA07760 A. Hardware Configuration THERMIDISTAT CONFIGURATION RECORDB. Mode Settings C. Home, Away, Sleep SettingsE. Configuration Options Catalog No: IIT6---PRH---02 E. Configuration Options cont