Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07044, A07045 Configuration Options -Selection, Option 01 — Equipment Type

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 26

Option 31* — Daylight Savings Time Configuration (programmable models only)

Option 32 — Furnace Heat Staging

Option 33 — Single or Two-Piece Installation Option 99 — Reset to Factory Defaults

TO ENTER CONFIGURATION MODE

Press and hold FAN button for approximately 10 sec. The Display Module is now in configuration mode. It will automatically exit this mode if no button is pressed for 3 minutes. Pressing the DONE button will exit configuration mode immediately.

WHILE IN CONFIGURATION MODE

The option number is displayed in the heat setpoint location and the configuration setting is displayed in the cool setpoint location. On the T6-PRH (programmable) model, a box will surround the option number. The mode button is used to move the box between the two displayed values. The soft keys below the listed values may also be used to move the box between selected values. The value inside the box is changed by using the UP/DOWN buttons. On the T6-NRH (non-programmable) model, one of the values will be flashing. The mode button is used to change which value is flashing or the Home and Sleep buttons may also be used to select which value to flash. The value that is flashing is changed by using the UP/DOWN buttons. All changes made are saved at the time of selection and will be saved in the event of the 3 minute time-out or when installer exits from configuration menu.

Configuration Options —Selection

Option 01 — Equipment Type

Range: H2, A2, HP, AC, hh, h2, H, C

26

Image 26

Bryant A07044, A07045 installation instructions Configuration Options -Selection, Option 01 — Equipment Type

Contents

Programmable Control Installation InstructionsT6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTAT Non---ProgrammableControlTABLE OF CONTENTS SAFETY CONSIDERATIONSINTRODUCTION INSTALLATION CONSIDERATIONS PowerFig. 1 - PCB Breakout Jumper ModelsHumidify Equipment and Connections ELECTRICAL OPERATION HAZARD Outdoor Temperature SensorDehumidify Equipment and Connections Remote Indoor Temperature Sensor Two-PieceThermidistat ConfigurationINSTALLATION Fig. 2 - T6-PRHCarton ContentsFig. 3 - T6-NRHCarton Contents Thermidistat Control LocationInstall Thermidistat Control ELECTRICAL OPERATION HAZARDUNIT DAMAGE HAZARD Two-PieceInstallation ENVIRONMENTAL HAZARDA07225 Fig. 4 - Press Tabs to Remove BackplateFig. 5 - Take Apart A07226Fig. 6 - Backplate Mounting Fig. 7 - Control Module Wiring Guide RelaysA07166 Fig. 8 - Secure Wires to Terminal StripFig. 9 - Connect Pigtail Wires to Display Module A07167Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Room Temperature Offset Adjustment Adjustable Setpoint Deadband not available onSmart Recovery programmable models only Humidity Offset AdjustmentConfiguration Options -Selection Option 01 — Equipment TypeOption 04 — Fan G On With W/W1 Option 02 — Clean Filter TimerOption 03 — Fahrenheit/Centigrade Option 07 - Zoning Option 08 - Auxiliary Heat Lockout TemperatureOption 06 - Cooling Lockout Below 55 F Option 09 - Heat Pump Lockout Temperature Option 10 - Reversing ValveOption 13 — Room Air Temperature Offset Adjust Option 11 — Deadband Setting Between Heat & CoolOption 12 — Smart Recovery Option 14 — Humidity Display Offset AdjustOption 16 — Maximum Cycles Per Hour Option 17 — Time Between Equipment StagesOption 18 - Backlight Configuration Default is OF off Default is OF off Option 22 — High Cool Latch Temperature Option 23 — High Heat Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 29 - Humidifier Pad Reminder Option 27 — Maximum Heating SetpointOption 28 - UV Light Reminder Default is OF off Option 33 — Single or Two-PieceInstallation Option 99 — Reset to Factory DefaultsSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidity Control Features HumidificationTable 2 - Humidification Selections To Select Humidification programmableAdditional Humidify Comments DehumidificationTo Select Humidification non-programmable 1.Normal Dehumidify Operation 2.Cool to DehumidifyFig. 16 - Auto Humidity 3.Dehumidify OffAdditional Dehumidify Comments Dehumidify Output and Equipment ConnectionsVacation programmable models only Vacation Humidification Table 3 – Vacation Setpoints Default ValuesVacation Setpoints Vacation DehumidificationTen-MinuteStaging Timer TimersCycle Timer OPERATIONAL INFORMATIONThree-MinuteMinimum on Time Equipment On IndicatorsHeat/Cool Setpoints Desired Temperature Emergency Heat Mode Humidify and Dehumidify IndicatorsAuto Changeover Programmable Fan programmable models onlyTROUBLESHOOTING Error CodesE2 - There is no E2 error message COOL Table 4 - Equipment Configuration OutputsEQUIPMENT COOLCOOL Table 4 - Equipment Configuration Outputs contEQUIPMENT COOLWIRING DIAGRAMS A07164Fig. 18 - FV/FK Fan Coil w/2-StageHeat Pump A06573Fig. 19 - Typical Fan Coil w/Heat Pump A06574A06575 Fig. 21 - FV/FK Fan Coil w/2-StageAir Conditioner A06576Fig. 22 - Typical Fan Coil w/Air Conditioner A06577A06578 Fig. 24 - FV/FK Fan Coil w/1-StageHeat Pump A06579Fig. 25 - Typical Fan Coil Heating Only A06580Page Fig. 27 - FV/FK Fan Coil w/1-StageAir Conditioner A06582Fig. 28 - Typical Fan Coil Cooling Only A06583A06584 Fig. 30 - Single-StageFurnace w/Heat Pump A006585A06586 Fig. 32 - Single-StageFurnace w/Air Conditioner A06587A06588 Fig. 34 - Single-StageFurnace Heating Only A06589Air Conditioner A06590A07760 B. Mode Settings THERMIDISTAT CONFIGURATION RECORDA. Hardware Configuration C. Home, Away, Sleep SettingsE. Configuration Options E. Configuration Options cont Catalog No: IIT6---PRH---02