Manuals / Bryant / Household Appliance / Air Conditioner

Bryant A07045, A07044 installation instructions Final Settings

Models: A07045 A07044

1 80

Download 80 pages 37.14 Kb

Page 41

installation, only 1 stage of auxiliary heat is available. Any staging of auxiliary heat must be managed by the furnace or fan coil. While the heating test is active, the humidify output can be toggled. On the programmable models, pressing the button below the humidify icon shall toggle the state of the humidify output. On the non-programmable models, pressing the features button shall toggle the state of the humidify output.

Installer test for cooling is the same as described for heating above. COOL ON will be displayed during cooling in Installer Test Mode. While the cooling test is active, the dehumidify icon shall be displayed if the dry contact has been configured as a DEHUM output. On the programmable models, pressing the button below the dehumidify icon shall toggle the state of the dry contact output. On the non-programmable models, pressing the features button shall toggle the state of the dry contact.

In a heat pump application, when the mode is set to “em heat” the auxiliary heat will turn on for 3 minutes. The clock display will count down from 180 to 0 during this test.

TO TEST FAN

Fan button switches FAN icon between AUTO and On. While On is displayed, G output will be energized, turning fan on. Allow up to 10 sec after button is pressed for fan to turn On and off. On some fan coils, fan continues to operate for 90 sec after G signal is removed.

Final Settings

Be sure to press DONE to exit installer setup mode. If the system is to be left in operation after installation is complete, use MODE button to select between HEAT, COOL, or AUTO to provide desired operation of heating, cooling, or auto.

41

Image 41

Bryant A07045, A07044 installation instructions Final Settings

Contents

T6-PRH, T6-NRH PREFERREDt SERIES THERMIDISTAT Installation InstructionsProgrammable Control Non---ProgrammableControlSAFETY CONSIDERATIONS TABLE OF CONTENTSINTRODUCTION Power INSTALLATION CONSIDERATIONSFig. 1 - PCB Breakout Jumper ModelsHumidify Equipment and Connections ELECTRICAL OPERATION HAZARD Outdoor Temperature SensorDehumidify Equipment and Connections Two-PieceThermidistat Configuration Remote Indoor Temperature SensorFig. 2 - T6-PRHCarton Contents INSTALLATIONThermidistat Control Location Fig. 3 - T6-NRHCarton ContentsELECTRICAL OPERATION HAZARD Install Thermidistat ControlUNIT DAMAGE HAZARD ENVIRONMENTAL HAZARD Two-PieceInstallationFig. 5 - Take Apart Fig. 4 - Press Tabs to Remove BackplateA07225 A07226Fig. 6 - Backplate Mounting Relays Fig. 7 - Control Module Wiring GuideFig. 9 - Connect Pigtail Wires to Display Module Fig. 8 - Secure Wires to Terminal StripA07166 A07167Fig. 10 - Attach Display to Backplate Fig. 11 - Equipment Control Module on Equipment Fig. 12 - Standoff Fig. 13 - Cover on Equipment Control Module Single-PieceInstallation Fig. 14 - Equipment Control Module Fig. 15 - Reattach Display Module Set Thermidistat Control Configuration Smart Recovery programmable models only Adjustable Setpoint Deadband not available onRoom Temperature Offset Adjustment Humidity Offset AdjustmentOption 01 — Equipment Type Configuration Options -SelectionOption 04 — Fan G On With W/W1 Option 02 — Clean Filter TimerOption 03 — Fahrenheit/Centigrade Option 07 - Zoning Option 08 - Auxiliary Heat Lockout TemperatureOption 06 - Cooling Lockout Below 55 F Option 10 - Reversing Valve Option 09 - Heat Pump Lockout TemperatureOption 12 — Smart Recovery Option 11 — Deadband Setting Between Heat & CoolOption 13 — Room Air Temperature Offset Adjust Option 14 — Humidity Display Offset AdjustOption 17 — Time Between Equipment Stages Option 16 — Maximum Cycles Per HourOption 18 - Backlight Configuration Default is OF off Default is OF off Option 23 — High Heat Latch Temperature Option 22 — High Cool Latch TemperatureOption 26 - Minimum Cooling Setpoint Option 29 - Humidifier Pad Reminder Option 27 — Maximum Heating SetpointOption 28 - UV Light Reminder Default is OF off Option 99 — Reset to Factory Defaults Option 33 — Single or Two-PieceInstallationSYSTEM START-UPAND CHECKOUT Final Settings Table 1 - Energy Star Default Schedule Humidification Humidity Control FeaturesTo Select Humidification programmable Table 2 - Humidification SelectionsAdditional Humidify Comments DehumidificationTo Select Humidification non-programmable 2.Cool to Dehumidify 1.Normal Dehumidify Operation3.Dehumidify Off Fig. 16 - Auto HumidityDehumidify Output and Equipment Connections Additional Dehumidify CommentsVacation programmable models only Vacation Setpoints Table 3 – Vacation Setpoints Default ValuesVacation Humidification Vacation DehumidificationCycle Timer TimersTen-MinuteStaging Timer OPERATIONAL INFORMATIONThree-MinuteMinimum on Time Equipment On IndicatorsHeat/Cool Setpoints Desired Temperature Auto Changeover Humidify and Dehumidify IndicatorsEmergency Heat Mode Programmable Fan programmable models onlyError Codes TROUBLESHOOTINGE2 - There is no E2 error message EQUIPMENT Table 4 - Equipment Configuration OutputsCOOL COOLEQUIPMENT Table 4 - Equipment Configuration Outputs contCOOL COOLA07164 WIRING DIAGRAMSA06573 Fig. 18 - FV/FK Fan Coil w/2-StageHeat PumpA06574 Fig. 19 - Typical Fan Coil w/Heat PumpA06575 A06576 Fig. 21 - FV/FK Fan Coil w/2-StageAir ConditionerA06577 Fig. 22 - Typical Fan Coil w/Air ConditionerA06578 A06579 Fig. 24 - FV/FK Fan Coil w/1-StageHeat PumpA06580 Fig. 25 - Typical Fan Coil Heating OnlyPage A06582 Fig. 27 - FV/FK Fan Coil w/1-StageAir ConditionerA06583 Fig. 28 - Typical Fan Coil Cooling OnlyA06584 A006585 Fig. 30 - Single-StageFurnace w/Heat PumpA06586 A06587 Fig. 32 - Single-StageFurnace w/Air ConditionerA06588 A06589 Fig. 34 - Single-StageFurnace Heating OnlyA06590 Air ConditionerA07760 A. Hardware Configuration THERMIDISTAT CONFIGURATION RECORDB. Mode Settings C. Home, Away, Sleep SettingsE. Configuration Options Catalog No: IIT6---PRH---02 E. Configuration Options cont