Bunn 41343 Enable Ads ? No Done Yes, Set Temp Xxx - Done +, Set Ready Xxx - Done +, Enable Ads?

PROGRAMMING FUNCTIONS - (cont.)

ENABLE ADS?

This function allows the operator to choose whether or not to display the advertising message that was en- tered into the brewer with an AD CARD. This message will be displayed when the brewer is not in use.

ENABLE ADS ?

NO DONE YES

Procedure to Enable/Disable Ads:

1.Press and hold upper right hidden switch until the display reads UNITS. Release switch. Continue to press and release switch until the display reads ENABLE ADS. The YES or NO will be flashing to indicate the current selection.

2.Press and release the NO to disable this function (no ads will be displayed on the screen), or;

3.Press and release the YES to enable this function (ads will be displayed on screen).

4.When finished, press and release DONE to save the new setting, exit the ENABLE ADS function and advance to the next function screen, SET TEMP. Another alternative is to press and release the ON/OFF switch (either on DUAL brewers) located on the front switch panel to exit the ENABLE ADS function and return to the MAIN SCREEN.

SET TEMP - Range: 185˚F (85˚C) to 205˚F (96˚C) This function allows the operator to set the brew

water temperature in the tank. It also sets the hot water faucet dispense temperature.

SET TEMP: XXX° (-) DONE (+)

Procedure to set brew temperature:

1.Press and hold upper right hidden switch until the display reads UNITS. Release switch. Continue to press and release switch until the display reads

SET TEMP.

2.To adjust the brew temperature, press (-)to de- crease or (+) to increase the brew temperature.

3.When finished, press and release DONE to save the new setting, exit the SET TEMP function and advance to the next function screen, SET READY. Another alternative is to press and release the ON/ OFF switch (either on DUAL brewers) located on the front switch panel to exit the SET TEMP func- tion and return to the MAIN SCREEN.

SET READY - Range: 185˚F (85˚C) to 203˚F (95˚C)

Brew water temperature is factory set at 200∞F (93.3∞C) Areas of high altitude will require lowering this tempera- ture to prevent boiling. This chart should be used as a guide when readjusting the brew water temperature.

Altitude	Boiling point		Recommended
	of water		water temperature
(Feet)	∞F	∞C	∞F	∞C
-1000	213.8	101.0	200	93.3
-500	212.9	100.5	200	93.3
0	212.0	100.0	200	93.3
500	211.1	99.5	200	93.3
1000	210.2	99.0	200	93.3
1500	209.3	98.5	200	93.3
2000	208.4	98.0	200	93.3
2500	207.4	97.4	200	93.3
3000	206.5	96.9	199	92.8
3500	205.6	96.4	198	92.2
4000	204.7	95.9	197	91.7
4500	203.8	95.4	196	91.1
5000	202.9	94.9	195	90.6
5500	201.9	94.4	195	90.6
6000	201.0	93.9	194	90.0
6500	200.1	93.4	193	89.4
7000	199.2	92.9	192	88.9
7500	198.3	92.4	191	88.3
8000	197.4	91.9	190	87.8
8500	196.5	91.4	189	87.2
9000	195.5	90.8	188	86.7
9500	194.6	90.3	187	86.1
10000	193.7	89.8	186	85.6

This function allows the operator to set the mini- mum temperature allowable to start a brew cycle. The range can be from 185˚F (85˚C) to within 2˚F (-1.7°C) of the SET TEMP. The water must be at the SET READY temperature or higher for the display to indicate READY TO BREW. If brew lockout is enabled, the brewing pro- cess will not start below this READY temperature.

NOTE: The upper limit for SET READY temperature is 2˚F (-1.7°C) less than the water temperature (SET TEMP) setting.

SET READY: XXX° (-) DONE (+)

Page 30 41343 080108