Programming Switch | Bunn S/N SNG0033000 & UP specs

PROGRAM ENABLE

PROGRAMMING LOCKOUT SWITCH (mounted on main control board)

This switch can be set to prevent access to the programming levels of the brewer. Once all the cor- rect brew settings are programmed, the operator can set the switch to the "DISABLE" position to prohibit anyone from changing the settings.

BREW LOCKOUT? NO DONE YES

This screen will be shown when the brewer is ready for use. The screen displays the water temperature in the tank. When the water in the tank reaches the correct set temperature, the display will change from HEATING to READY TO BREW.

This function allows the operator to prevent or allow brewing if the water temperature is less than the set READY temperature.

To access this function screen press and hold the ® symbol. Release the ® when the display reads:

READY TO BREW WATER TEMP: 205°

PROGRAMMING THE BREWER

The programming of the brewer is divided into two levels. There is one function in Level 1. All other functions are accessed in Level 2.

The following function screens are in order of appearance. Each screen will have instructions on how to access, and the procedures to program the various functions of the brewer.

IMPORTANT PROGRAMMING NOTES

- READ CAREFULLY -

To exit the programming mode at any time, press and release the ON/OFF switch located on the front switch panel. The display will return to the MAIN SCREEN.

If none of the five programming switches are pressed within one minute during the setup of the brewer, the programming of the function screen that is being set will be exited and the display will return to the MAIN

SCREEN.

Always remember to place a container and funnel under the sprayhead when operating the brewer during the set-up of PULSE BREW, CALIBRATE FLOW and testing the brew and bypass valves in SERVICE TOOLS/TEST

OUTPUTS.

MAIN SCREENPROGRAM FUNCTIONS - LEVEL 1 BREW LOCKOUT

DISABLE

PROGRAMMING

SWITCH

P2424

Press here	Press here	Press here
for NO	for DONE	for YES

The YES or NO should be flashing. Select YES to prevent brewing if the water temperature is below the set READY temperature. Select NO to permit brewing at any water temperature.

When finished, press and release DONE. This will exit this function screen and return to the MAIN SCREEN on the display.

Page 13	35879.1 071405

Image 13

Bunn S/N SNG0033000 & UP manual Programming Switch

Contents

Phone 217 529-6601 FAX 217 Single TF DBC BUNN-O-MATIC Commercial Product Warranty Table of Contents User Notices Electrical HOOK-UP Volt ac single phase Hz models37881.0002 230 volt ac Single phase, 60 Hz models Electrical Requirements Models without power cord Plumbing Requirements CE RequirementsPlumbing HOOK-UP Batch Selector Switches Main ON/OFF SwitchON/OFF Switch Enable Brew Brew Switch Coffee Brewing Initial Setup Cleaning Glossary Programming Programming Switches Programming Switch Recipes Program Functions LevelDRIP-OUT Times Continues to D LevelReturns to a Return to a Program Flow DiagramContinues to Programming the Brewer Procedure for modifying units of measure Units Setting Units of Measure SET NEW Recipe Procedure for Setting the RecipeThis function allows the operator to set Brew Sizes DONE? SET NEW RecipesRefer to SET Pulse Brew for description Card Contains Recipe for Procedure to program the coffee name Review RECIPES? Noyes Procedure for reviewing recipes Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee NamesNext To exit, press Next until the display reads That Screen Brew OZ Setting or Adjusting Brew VOL- Umes Review Recipes Bypass Modifying pulse brew Range 1st on time off to 4 minutes SET Pulse Brew SET Pulse Brew NO-NAME Modifyshownext SET Pulse Brew Easy Pulse Setup TIMES? SET Pulse Brew Enter TimesDONE? Batches DONE? SET Preinfusion Setup Complete Assign Recipes Enable ADS?Assign Recipe ? SET Ready SET TempScreen Spray OZ/M Calibrate Flow Bypass OZ/MCalibrate Spray .. Press Brew to Start Calibrate Flow Procedures to calibrate the bypass flow rateStart Procedures to view/reset the brew counters Procedure to set funnel detectBrew Counters Funnel Detect optional Testing individual components outputs Service ToolsProcedure to test components outputs Brew Valve Frequency Nothing Pressed Procedure to set factory defaults Factory Defaults Troubleshooting Procedures TroubleshootingScreen Displayed Possible Cause Press ON/OFF to terminate the cycle Temperature Press ON/OFF to terminate the brew cycle ON/OFF switch was pressed after the brew cycle was startedTank Heater failure Triac Failure Wires shorted to housing, or to Temperature Sensor ProbeWater shut off to brewer Broken or not making connection Brew switch Switch test procedures Equipment will not operate No power or incorrect voltageBrew Valve Switch test procedures Data plate within +/- 10% Overflow Protection Switch When this condition occurs, Troubleshooting Problem Possible CauseWith power removed from brewer Holding it in open state See above or boiling Heating Time TOO Long Limit Thermostat Troubleshooting Problem Server Pointing towards the brewer Inconsistent beverage level StrainerImproper water pressure 90 psi 138 and 620 kPa Water temperature Consistently high or low beverage Brew Volume adjustmentLevel in server For each brew cycle Remove and clean lime off tank heaters Troubleshooting Problem Possible Cause Weak beverageBrewer is making unusual noises Plumbing lines Water Supply Tank Heaters Schematic Wiring Diagram Single TF DBC Schematic Wiring Diagram Wire Single Phase Schematic Wiring Diagram Single TF DBC