Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems Chapter Unpacking and Installing Your ELS100-16TX, ELS100-16TX Front Panel

Models: 100

1 110

Download 110 pages 23.48 Kb

Page 33

CHAPTER 2

UNPACKING AND INSTALLING

YOUR ELS100-16TX

Carefully unpack the ELS100-16TX from the shipping carton and inspect it for possible damage. If any damage is evident, contact your supplier. The shipping carton contains the following:

•The ELS100-16TX unit

•One AC power cord

•Console Cable kit

•Two rack-mounting brackets with fasteners (for rack-mount installation)

•Documentation – In addition to this manual, the Getting Started with the SmartSTACK 100 ELS100-16TXguide, and Release Notes are also included.

Only qualiﬁed personnel should perform installation procedures.

2.1 ELS100-16TX FRONT PANEL

The ELS100-16TX provides 16 IEEE 802.3 10/100 BASE-T autosensing Ethernet ports. The ELS100-16TX provides the option of substituting ports RJ45 ports 15 and 16 (either or both) with two EPIM ports. These ports accept the EPIM-100FX.

Each ELS100-16TX also includes an RS232C port for out-of-band management. Figure 2-1 shows the ELS100-16TX’s front panel. The LEDs and buttons are described in Tables 2-1 and 2-2.

2-1

Image 33

Cabletron Systems manual Chapter Unpacking and Installing Your ELS100-16TX, ELS100-16TX Front Panel

Contents

User Guide Page FCC Notice DOC Notice Cabletron Software Program License Declaration of Conformity Contents Monitoring and Managing Your ELS100-16TX ELS100-16TX Diagnostics Troubleshooting Appendix B Glossary Appendix a Technical Specifications Contents Viii Chapter Introduction About this Manual Your email address Getting Help Document Conventions Related Documentation ELS100-16TX Front Panel Overview SmartSTACK 100 ELS100-16TX Architecture Introduction Autonegotiation Port Trunking Discarding Local Trafﬁc Store and Forward Switching Spanning Tree Algorithm Typical Switching Application SmartSTACK 100 ELS100-16TX Bridge Address Table SmartSTACK 100 ELS100-16TX Sample Applications SmartSTACK 100 ELS100-16TX Port Mirroring SmartSTACK 100 ELS100-16TX Trunking SmartSTACK 100 ELS100-16TX Trunking with 100 Mbps Ports Virtual Workgroups Repeater Traffic Workgroup a Workgroup B Local Console Manager Command Syntax Conventions Help Basic LCM Commands ELS100-16TX Local Console Manager Erase Exit or LogoutTraplog Introduction ELS100-16TX Front Panel Chapter Unpacking and Installing Your ELS100-16TX Port LEDs 100BASE-T Epim Ports Reset Switch Status LEDs ACT Describes the ELS100-16TX buttons Installing AN Epim Installing an Epim Rack-Mounting an ELS100-16TX Installing the ELS100-16TX Attaching Rackmount Brackets Connecting the Local Console Manager Checking the POWER-UP Diagnostics Sequence Connecting to the Network ELS100-16TX Twisted Pair Connection Connecting UTP Cables Cable Pinouts RJ45 Crossover Cable Connecting a Segment to the EPIM-100FX Fiber Optic Network Connection EPIM-100FX Port Unpacking and Installing Your ELS100-16TX Spectrum Spel Spma Chapter Configuring Your ELS100-16TX Assigning IP Addresses Type ipaddr PORT-NUMBER IP Address Displaying IP Addresses Deleting an IP AddressChanging a Subnet Mask To change the subnet mask, at the LCM prompt Enabling Bridging Displaying Bridging Functions Disabling Bridging Enabling Trunking 100BASE-T Crossover Cables Trunk Groups Trunk Groups Disabling Trunking Display could look like the following Displaying Trunking Status Enabled, Rip listening Disabling Mirroring Enabling Port Mirroring Displaying Mirroring Status To check the status for ports conﬁgured for mirroring Deﬁning Virtual Workgroups Defining and Deleting Workgroups LCM responds with the following display Assigning a Community Name Configuring BROADCAST/MULTICAST Storm Protection System Contact Modifying MIB Variables System Name System LocationCommunity Names Aging Parameter Set Community Name Chapter Monitoring and Managing Your ELS100-16TX ELS100-16TX Management ToolsELS100-16TX Statistics System Statistics Gathering Statistics Ethernet Port Statistics Displaying Status Using LCM to Check ELS100-16TX Status Enabled, Rip listening Displaying MAC Addresses To display all MAC addresses, at the LCM prompt LCM would display Displaying Manufacturing Information Managing the ELS100-16TX Using LCM to Manage the ELS100-16TX Enabling a Port Disabling a Port NoRIP Option Changing a Community Name Setting the Baud Rate Setting a Reboot Time Chapter ELS100-16TX Diagnostics and Troubleshooting POWER-UP DiagnosticsPower-up LED Sequence Software Checksum Comparison Speciﬁc Power-up Tests Power-up Diagnostics Results Responses to Failures AT POWER-UPStatus and Activity Indicators ELS100-16TX Front Panel LEDs ACT ELS100-16TX does not Power UP Connectivity Problems 2 ELS100-16TX Has Rebooted3 ELS100-16TX Does Not Respond to NMS ELS100-16TX Diagnostics and Troubleshooting Physical Connector PortsElectrical Environmental Standard Support Diagnostic LEDs Management Support Address Table SizeRegulatory Compliance Serial Cable PIN Assignments 100BASE-T PIN Assignments Connectors Crossover Wiring STRAIGHT-THROUGH Wiring 5 4 3 Rule EPIM-100FX Specifications Cable Type Worst Case Budget Typical Budget Technical Speciﬁcations Address AlarmAddress table Agent Bandwidth BackboneBpdu bridge protocol data unit Bps bits per second Data link layer CongestionDatagram Data rate or speed Encapsulation Full wire speedEncode Entity Icmp Internet control message protocol Intelligent bridge/switchIeee Initialization Interoperability InternetworkingIP Internet protocol ISO International Standards Organization Mask MAC media access controlMbps megabits per second MIB management information base Propagation delay Power budgetOSI Open Systems Interconnection Packet Service Rarp reverse address resolution protocolProtocol Protocol suite Symbol SwitchSynchronous transmission Translating bridge WAN wide area network Upstream Glossary