Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 100 manual Enabling Bridging, To change the subnet mask, at the LCM prompt

Models: 100

1 110

Download 110 pages 23.48 Kb

Page 51

Conﬁguring Your ELS100-16TX

To change the subnet mask, at the LCM prompt:

1.Type ipaddr <PORT-NUMBER> <IP ADDRESS> <SUBNET MASK>

For example, ipaddr 6 192.138.217.40 255.255.240.0 would set the subnet mask for port 6 to 255.255.240.0. LCM responds by redisplaying the current address table.

Note: When you change the subnet mask for a port, you must also enter the IP address for that port. Make sure you enter the IP address for the port correctly; whatever you enter becomes the IP address for that port.

3.2 ENABLING BRIDGING

The LCM bridge command allows you to set bridging options for a single port or a range of ports. The options include:

•off

•on (the default with BPDU enabled)

•noBPDU

BPDU (Bridge Protocol Data Unit) is a data unit transmitted as part of the IEEE 802.1d Spanning Tree protocol. The exchange of BPDUs allows bridges within a network to logically conﬁgure the network as a single spanning tree.

Note: Selecting the noBPDU option could make your network inoperable

because the ELS100-16TX would be unable to detect loops.

3-5

Image 51

Cabletron Systems 100 manual Enabling Bridging, To change the subnet mask, at the LCM prompt

Contents

User Guide Page FCC Notice DOC Notice Cabletron Software Program License Declaration of Conformity Contents Monitoring and Managing Your ELS100-16TX ELS100-16TX Diagnostics Troubleshooting Appendix B Glossary Appendix a Technical Specifications Contents Viii Chapter Introduction About this Manual Your email address Getting Help Document Conventions Related Documentation ELS100-16TX Front Panel Overview SmartSTACK 100 ELS100-16TX Architecture Introduction Autonegotiation Port Trunking Discarding Local Trafﬁc Store and Forward Switching Spanning Tree Algorithm Typical Switching Application SmartSTACK 100 ELS100-16TX Bridge Address Table SmartSTACK 100 ELS100-16TX Sample Applications SmartSTACK 100 ELS100-16TX Port Mirroring SmartSTACK 100 ELS100-16TX Trunking SmartSTACK 100 ELS100-16TX Trunking with 100 Mbps Ports Virtual Workgroups Repeater Traffic Workgroup a Workgroup B Local Console Manager Command Syntax Conventions Help Basic LCM Commands ELS100-16TX Local Console Manager Erase Exit or LogoutTraplog Introduction ELS100-16TX Front Panel Chapter Unpacking and Installing Your ELS100-16TX Port LEDs 100BASE-T Epim Ports Reset Switch Status LEDs ACT Describes the ELS100-16TX buttons Installing AN Epim Installing an Epim Rack-Mounting an ELS100-16TX Installing the ELS100-16TX Attaching Rackmount Brackets Connecting the Local Console Manager Checking the POWER-UP Diagnostics Sequence Connecting to the Network ELS100-16TX Twisted Pair Connection Connecting UTP Cables Cable Pinouts RJ45 Crossover Cable Connecting a Segment to the EPIM-100FX Fiber Optic Network Connection EPIM-100FX Port Unpacking and Installing Your ELS100-16TX Spectrum Spel Spma Chapter Configuring Your ELS100-16TX Assigning IP Addresses Type ipaddr PORT-NUMBER IP Address Displaying IP Addresses Deleting an IP AddressChanging a Subnet Mask To change the subnet mask, at the LCM prompt Enabling Bridging Displaying Bridging Functions Disabling Bridging Enabling Trunking 100BASE-T Crossover Cables Trunk Groups Trunk Groups Disabling Trunking Display could look like the following Displaying Trunking Status Enabled, Rip listening Disabling Mirroring Enabling Port Mirroring Displaying Mirroring Status To check the status for ports conﬁgured for mirroring Deﬁning Virtual Workgroups Defining and Deleting Workgroups LCM responds with the following display Assigning a Community Name Configuring BROADCAST/MULTICAST Storm Protection System Contact Modifying MIB Variables System Name System LocationCommunity Names Aging Parameter Set Community Name Chapter Monitoring and Managing Your ELS100-16TX ELS100-16TX Management ToolsELS100-16TX Statistics System Statistics Gathering Statistics Ethernet Port Statistics Displaying Status Using LCM to Check ELS100-16TX Status Enabled, Rip listening Displaying MAC Addresses To display all MAC addresses, at the LCM prompt LCM would display Displaying Manufacturing Information Managing the ELS100-16TX Using LCM to Manage the ELS100-16TX Enabling a Port Disabling a Port NoRIP Option Changing a Community Name Setting the Baud Rate Setting a Reboot Time Chapter ELS100-16TX Diagnostics and Troubleshooting POWER-UP DiagnosticsPower-up LED Sequence Software Checksum Comparison Speciﬁc Power-up Tests Power-up Diagnostics Results Responses to Failures AT POWER-UPStatus and Activity Indicators ELS100-16TX Front Panel LEDs ACT ELS100-16TX does not Power UP Connectivity Problems 2 ELS100-16TX Has Rebooted3 ELS100-16TX Does Not Respond to NMS ELS100-16TX Diagnostics and Troubleshooting Environmental Connector PortsPhysical Electrical Standard Support Diagnostic LEDs Serial Cable PIN Assignments Address Table SizeManagement Support Regulatory Compliance 100BASE-T PIN Assignments Connectors Crossover Wiring STRAIGHT-THROUGH Wiring 5 4 3 Rule EPIM-100FX Specifications Cable Type Worst Case Budget Typical Budget Technical Speciﬁcations Agent AlarmAddress Address table Bps bits per second BackboneBandwidth Bpdu bridge protocol data unit Data rate or speed CongestionData link layer Datagram Entity Full wire speedEncapsulation Encode Initialization Intelligent bridge/switchIcmp Internet control message protocol Ieee ISO International Standards Organization InternetworkingInteroperability IP Internet protocol MIB management information base MAC media access controlMask Mbps megabits per second Packet Power budgetPropagation delay OSI Open Systems Interconnection Protocol suite Rarp reverse address resolution protocolService Protocol Translating bridge SwitchSymbol Synchronous transmission WAN wide area network Upstream Glossary