Declaration of Conformity | Cabletron Systems 100 instruction

Notice

DECLARATION OF CONFORMITY

Application of Council Directive(s): 89/336/EEC 73/23/EEC

Manufacturer’s Name: Cabletron Systems, Inc.

Manufacturer’s Address: 35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name: Mr. J. Solari

European Representative Address: Cabletron Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment: Networking Equipment, for use in a

Commercial or Light Industrial Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this notice conforms to the above directives.

Manufacturer	Legal Representative in Europe
Mr. Ronald Fotino	Mr. J. Solari
___________________________________	___________________________________
Full Name	Full Name
Principal Compliance Engineer	Managing Director - E.M.E.A.
___________________________________	___________________________________
Title	Title
Rochester, NH, USA	Newbury, Berkshire, England
___________________________________	___________________________________
Location	Location

iv

Image 6

Cabletron Systems 100 manual Declaration of Conformity

Contents

User Guide Page FCC Notice DOC Notice Cabletron Software Program License Declaration of Conformity Contents ELS100-16TX Diagnostics Troubleshooting Monitoring and Managing Your ELS100-16TX Appendix a Technical Specifications Appendix B Glossary Contents Viii Chapter Introduction About this Manual Getting Help Your email address Document Conventions Related Documentation Overview ELS100-16TX Front Panel SmartSTACK 100 ELS100-16TX Architecture Introduction Port Trunking Autonegotiation Store and Forward Switching Discarding Local Trafﬁc Typical Switching Application Spanning Tree Algorithm SmartSTACK 100 ELS100-16TX Bridge Address Table SmartSTACK 100 ELS100-16TX Port Mirroring SmartSTACK 100 ELS100-16TX Sample Applications SmartSTACK 100 ELS100-16TX Trunking Virtual Workgroups SmartSTACK 100 ELS100-16TX Trunking with 100 Mbps Ports Repeater Traffic Workgroup a Workgroup B Local Console Manager Command Syntax Conventions Basic LCM Commands Help ELS100-16TX Local Console Manager Erase Exit or LogoutTraplog Introduction Chapter Unpacking and Installing Your ELS100-16TX ELS100-16TX Front Panel Port LEDs 100BASE-T Epim Ports Reset Switch Status LEDs ACT Installing AN Epim Describes the ELS100-16TX buttons Installing an Epim Installing the ELS100-16TX Rack-Mounting an ELS100-16TX Attaching Rackmount Brackets Checking the POWER-UP Diagnostics Sequence Connecting the Local Console Manager Connecting to the Network Connecting UTP Cables ELS100-16TX Twisted Pair Connection Connecting a Segment to the EPIM-100FX Cable Pinouts RJ45 Crossover Cable Fiber Optic Network Connection EPIM-100FX Port Unpacking and Installing Your ELS100-16TX Chapter Configuring Your ELS100-16TX Spectrum Spel Spma Assigning IP Addresses Type ipaddr PORT-NUMBER IP Address Displaying IP Addresses Deleting an IP AddressChanging a Subnet Mask Enabling Bridging To change the subnet mask, at the LCM prompt Disabling Bridging Displaying Bridging Functions Enabling Trunking Trunk Groups 100BASE-T Crossover Cables Trunk Groups Disabling Trunking Displaying Trunking Status Display could look like the following Enabled, Rip listening Enabling Port Mirroring Disabling Mirroring Displaying Mirroring Status To check the status for ports conﬁgured for mirroring Defining and Deleting Workgroups Deﬁning Virtual Workgroups LCM responds with the following display Assigning a Community Name Configuring BROADCAST/MULTICAST Storm Protection Modifying MIB Variables System Contact System Name System LocationCommunity Names Set Community Name Aging Parameter Chapter Monitoring and Managing Your ELS100-16TX ELS100-16TX Management ToolsELS100-16TX Statistics Gathering Statistics System Statistics Ethernet Port Statistics Using LCM to Check ELS100-16TX Status Displaying Status Enabled, Rip listening Displaying MAC Addresses To display all MAC addresses, at the LCM prompt Displaying Manufacturing Information LCM would display Using LCM to Manage the ELS100-16TX Managing the ELS100-16TX Disabling a Port Enabling a Port NoRIP Option Changing a Community Name Setting the Baud Rate Setting a Reboot Time Chapter ELS100-16TX Diagnostics and Troubleshooting POWER-UP DiagnosticsPower-up LED Sequence Speciﬁc Power-up Tests Software Checksum Comparison Power-up Diagnostics Results Responses to Failures AT POWER-UPStatus and Activity Indicators ELS100-16TX Front Panel LEDs ACT ELS100-16TX does not Power UP Connectivity Problems 2 ELS100-16TX Has Rebooted3 ELS100-16TX Does Not Respond to NMS ELS100-16TX Diagnostics and Troubleshooting Electrical Connector PortsPhysical Environmental Diagnostic LEDs Standard Support Regulatory Compliance Address Table SizeManagement Support Serial Cable PIN Assignments Connectors 100BASE-T PIN Assignments STRAIGHT-THROUGH Wiring Crossover Wiring EPIM-100FX Specifications 5 4 3 Rule Cable Type Worst Case Budget Typical Budget Technical Speciﬁcations Address table AlarmAddress Agent Bpdu bridge protocol data unit BackboneBandwidth Bps bits per second Datagram CongestionData link layer Data rate or speed Encode Full wire speedEncapsulation Entity Ieee Intelligent bridge/switchIcmp Internet control message protocol Initialization IP Internet protocol InternetworkingInteroperability ISO International Standards Organization Mbps megabits per second MAC media access controlMask MIB management information base OSI Open Systems Interconnection Power budgetPropagation delay Packet Protocol Rarp reverse address resolution protocolService Protocol suite Synchronous transmission SwitchSymbol Translating bridge Upstream WAN wide area network Glossary