Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 100 manual Address Table Size, Management Support, Regulatory Compliance

Models: 100

1 110

Download 110 pages 23.48 Kb

Page 93

Technical Speciﬁcations

Address Table Size

8,192 dynamic entries

Management Support

•MIB II, 802.1d, 802.3, and Cabletron Enterprise MIB

•Cabletron Systems Local Console Manager (LCM)

•Any SNMP-based network management system

Regulatory Compliance

Safety	UL 1950, CSA C22.2 No. 950,
	EN 60950, IEC 950 and
	73/23/EEC
Electromagnetic Compatibility	FCC Part 15, EN 55022,
	EN 50082-1, 89/336/EEC, CSA
	C108.8, VCCI V-3

A.2 SERIAL CABLE PIN ASSIGNMENTS

For a PC running a Windows terminal connected to the RS232C Network Management Port on the front panel of the ELS100-16TX, the following serial cable pin assignments (Tables A-1 and A-2) are required to manage the ELS100-16TX using the Local Console Manager (LCM).

Table A-1. DB25 Pin Assignments

ELS100-16TX RJ45 (female)		DB25-pin (female)

Pin 1	(Tx)	Pin 3

Pin 4	(Rx)	Pin 2

Pin 5	(GND)	Pin 7

A-3

Image 93

Cabletron Systems 100 manual Address Table Size, Management Support, Regulatory Compliance, Serial Cable PIN Assignments

Contents

User Guide Page FCC Notice DOC Notice Cabletron Software Program License Declaration of Conformity Contents Monitoring and Managing Your ELS100-16TX ELS100-16TX Diagnostics TroubleshootingAppendix B Glossary Appendix a Technical SpecificationsContents Viii Chapter Introduction About this Manual Your email address Getting HelpDocument Conventions Related Documentation ELS100-16TX Front Panel OverviewSmartSTACK 100 ELS100-16TX Architecture Introduction Autonegotiation Port TrunkingDiscarding Local Trafﬁc Store and Forward SwitchingSpanning Tree Algorithm Typical Switching ApplicationSmartSTACK 100 ELS100-16TX Bridge Address Table SmartSTACK 100 ELS100-16TX Sample Applications SmartSTACK 100 ELS100-16TX Port MirroringSmartSTACK 100 ELS100-16TX Trunking SmartSTACK 100 ELS100-16TX Trunking with 100 Mbps Ports Virtual WorkgroupsRepeater Traffic Workgroup a Workgroup B Local Console Manager Command Syntax Conventions Help Basic LCM CommandsELS100-16TX Local Console Manager Erase Exit or LogoutTraplog Introduction ELS100-16TX Front Panel Chapter Unpacking and Installing Your ELS100-16TXPort LEDs 100BASE-T Epim Ports Reset Switch Status LEDs ACT Describes the ELS100-16TX buttons Installing AN EpimInstalling an Epim Rack-Mounting an ELS100-16TX Installing the ELS100-16TXAttaching Rackmount Brackets Connecting the Local Console Manager Checking the POWER-UP Diagnostics SequenceConnecting to the Network ELS100-16TX Twisted Pair Connection Connecting UTP CablesCable Pinouts RJ45 Crossover Cable Connecting a Segment to the EPIM-100FXFiber Optic Network Connection EPIM-100FX Port Unpacking and Installing Your ELS100-16TX Spectrum Spel Spma Chapter Configuring Your ELS100-16TXAssigning IP Addresses Type ipaddr PORT-NUMBER IP Address Displaying IP Addresses Deleting an IP AddressChanging a Subnet Mask To change the subnet mask, at the LCM prompt Enabling BridgingDisplaying Bridging Functions Disabling BridgingEnabling Trunking 100BASE-T Crossover Cables Trunk GroupsTrunk Groups Disabling Trunking Display could look like the following Displaying Trunking StatusEnabled, Rip listening Disabling Mirroring Enabling Port MirroringDisplaying Mirroring Status To check the status for ports conﬁgured for mirroring Deﬁning Virtual Workgroups Defining and Deleting WorkgroupsLCM responds with the following display Assigning a Community Name Configuring BROADCAST/MULTICAST Storm Protection System Contact Modifying MIB VariablesSystem Name System LocationCommunity Names Aging Parameter Set Community NameChapter Monitoring and Managing Your ELS100-16TX ELS100-16TX Management ToolsELS100-16TX Statistics System Statistics Gathering StatisticsEthernet Port Statistics Displaying Status Using LCM to Check ELS100-16TX StatusEnabled, Rip listening Displaying MAC Addresses To display all MAC addresses, at the LCM prompt LCM would display Displaying Manufacturing InformationManaging the ELS100-16TX Using LCM to Manage the ELS100-16TXEnabling a Port Disabling a PortChanging a Subnet Mask NoRIP OptionChanging a Community Name Setting the Baud Rate Setting a Reboot Time Chapter ELS100-16TX Diagnostics and Troubleshooting POWER-UP DiagnosticsPower-up LED Sequence Software Checksum Comparison Speciﬁc Power-up TestsPower-up Diagnostics Results Responses to Failures AT POWER-UPStatus and Activity Indicators ELS100-16TX Front Panel LEDs ACT ELS100-16TX does not Power UP TroubleshootingConnectivity Problems 2 ELS100-16TX Has Rebooted3 ELS100-16TX Does Not Respond to NMS ELS100-16TX Diagnostics and Troubleshooting Physical Connector PortsElectrical EnvironmentalStandard Support Diagnostic LEDsManagement Support Address Table SizeRegulatory Compliance Serial Cable PIN Assignments100BASE-T PIN Assignments ConnectorsCrossover Wiring STRAIGHT-THROUGH Wiring5 4 3 Rule EPIM-100FX SpecificationsCable Type Worst Case Budget Typical Budget Technical Speciﬁcations Address AlarmAddress table AgentBandwidth BackboneBpdu bridge protocol data unit Bps bits per secondData link layer CongestionDatagram Data rate or speedEncapsulation Full wire speedEncode EntityIcmp Internet control message protocol Intelligent bridge/switchIeee InitializationInteroperability InternetworkingIP Internet protocol ISO International Standards OrganizationMask MAC media access controlMbps megabits per second MIB management information basePropagation delay Power budgetOSI Open Systems Interconnection PacketService Rarp reverse address resolution protocolProtocol Protocol suiteSymbol SwitchSynchronous transmission Translating bridgeWAN wide area network UpstreamGlossary