Installing the Switch | Cabletron Systems 6A000 specification

Installing the Switch

Switch Installation and Setup

2p›F A single 6C205-1 power supply (the older version of the 6C205-3) can support only two SmartCell 6A000s within a SmartSwitch 6000 chassis. Three SmartCell 6A000s can reside within a SmartSwitch 6000 chassis that contains two 6C205-1 power supplies.

Follow the instructions below to install the switch module into the chassis. Refer to Figure 2-2. s• Remove the metal blank that covers one of the empty slots in the chassis.

¢• Open the ejectors at the top and bottom of the switch module.

••With the LEDs at the top, align the top and bottom of the SmartCell 6A000 with the tracks in the slot.

T• Slide the switch into the chassis. The switch module obscures the view of the tracks at the bottom of the chassis, so be sure to look at that area as you begin to slide the switch into the chassis.

Q• Close the ejectors. The installation is complete.

2-4 SmartCell 6A000 User Guide

Image 22

Cabletron Systems 6A000 manual Installing the Switch

Contents

SmartCell 6A000 User Guide Ii SmartCell 6A000 User Guide FCC Class a Notice Declaration of Conformity Addendum Safety Information Class 1 Laser Transceivers Fiber Optic Protective Caps Regulatory Compliance Summary Safety Revision History Table of Contents Specifications Acronyms Index Xii SmartCell 6A000 User Guide List of Figures List of Figures Xiv SmartCell 6A000 User Guide List of Tables List of Tables Xvi SmartCell 6A000 User Guide Introduction Introduction SmartCell 6A000 User Guide Inspecting the Switch Switch Installation and SetupUnpacking the Switch Check Accessory Carton Contents 6A-IOM-29-4 Face Plate Number Physical Specification 6A-IOM-21-46A-IOM-22-4 6A-IOM-29-4-IR Installing the Switch 1 DS3 and E3 I/O Module Configuration Installing the Switch Configuring the Switch Switch Installation and Setup Configuring the Switch 6A000 console and network connections Using the Console Console Commands SmartCell ZX # show portconfig a1 Console Time-out Creating an Alias Ambiguous Commands Console Help SmartCell ZX # ? add laneclient Smartswitch ATM AdministratorExterior Installation Steps MB RAM Starting SmartSwitch ATM Administrator the First Time User Name Access Level Default Password Accessing Online Help SmartSwitch ATM Administrator IP Over ATM and Lane Creating AN IP Over ATM Vlan Server Is local Server Connection Established Creating AN Emulated LAN ATM Addressing for IP over ATM No Lane server address is specified see note below Ilmi Switch Clients ELANs Across Multiple SwitchesATM Addressing for LAN Emulation Elan1 ›amV˜m˜h¤d›F=˜/2 ˜˜,6˜3F˜1˜m=˜/2 SmartCell 6A000 User Guide Backing UP and Restoring Switch Configuration Switch AdministrationPath /backdir/config-1 Creating an Iisp Route ATM RoutingSmartCell ZX # show netprefix b2 Iisp Routing Considerations AtmAddress Iisp route across Pnni domain UNI Routes 200 Route MetricsCbr 750 IP Routing # show Pnnimetrics ZX # show route Route NET Events and Alarms Event Categories Viewing Events and Alarms SmartCell ZX # set eventdisplay SmartCell ZX # set alarmdisplay Deleting Events and AlarmsPVC Connections SmartCell ZX # show trafficdescriptor Point-to-Point PVCsPoint-to-Multipoint PVCs 100 Md1 #add trafficdescriptor Local Connecting to Local Switch Client Through a PVCNon-zero VPIs 10.1.1.0 VCC Mask Index VPI Bits VPI Values VCI Bits VCI Values ZX # set vccmask Use show portconfig to see the change to port A1 SmartCell ZX # set portconfig a1 Traffic Management Traffic Descriptors Type Number Descriptor Characteristics SmartCell ZX# show trafficdescriptor 5000 Call Admission Control Policy8000 ZX# add pvc Ubr Min for CBR queue SmartCell ZX # show switchtrafficcongestion QoS Queue Recommended SettingsEFCI, EPD, and RM Thresholds Accessing the Boot Load Prompt Upgrading and Changing Software Boot Load Commands Command Action Parameters Boot Prom Upgrading Boot Load SoftwareFlash RAM =df b =chpi Upgrading Post Diagnostic Software=df p Upgrading Switch Operating Software =df s Using the Update Firmware Command 214.95.77.240 Saving Core Dumps 204.95.77.240 Tftpboot/bobr/coreSet CoreDump command Bobr Error IP e0103288 PFP e04be080 R0pfp e04be040 R1sp e04be0c0 Troubleshooting Troubleshooting IP Over ATM Troubleshooting LAN Emulation Troubleshooting Pnni Links Troubleshooting Congestion Diagnosing Congestion Global Congestion Port Congestion Troubleshooting Congestion Appendix a Specifications Function Specification Value Ejector Table A-3 Physical Specifications Protocol Standard UNI Management Protocol Supported MIBs RJ-45 Pin RJ-45 Color DB-9 Pin DB-9 Description Technical Specifications Appendix B Agent Support MIB, SMI, MIB Files and Internet MIB Hierarchy ZeitNet Cabletron Proprietary MIBs MIB, SMI, MIB Files and Internet MIB Hierarchy Relation Between Object Identifier and the Represented Value Zeitnet Cabletron Proprietary MIB Groups Supported protocolsSupported SMI Formats Name Object Identifier Function SmartCell 6A000 MIB Support MIB Exceptions Non-Conformance Update firmware Backup Restore Reboot Console Commands that Affect the AgentManaging the Smartcell 6A000 Managing the SmartCell 6A000 Appendix C Technical Support FAX ServiceElectronic Services Telephone Assistance Software Warranty Hardware WarrantyRepair Services Appendix D Acronyms Isdn Bootp DTE FCS Ilmi LES Netbeui PDU RMA SVC VBR/RT Acronyms Appendix D-12 SmartCell 6A000 User Guide Index Numerics Elan Lane Snmp Lane VPI