Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems HSIM-A6DP manual Chapter Installation, Unpacking The Hsim

Models: HSIM-A6DP

1 100

Download 100 pages 18.73 Kb

Page 19

CHAPTER 2

INSTALLATION

This chapter contains instructions for the following tasks:

•Unpacking the HSIM (Section 2.1)

•Installing APIMs (Section 2.2)

•Installing an HSIM (Section 2.3)

To install the HSIM and APIMs, you need the following tools:

•Antistatic wrist strap (provided with the 6C105 chassis or standalone hub)

•Phillips screwdriver

2.1UNPACKING THE HSIM

Unpack the HSIM as follows:

!

CAUTION

The HSIM-A6DP and the host module or hub are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damage to the HSIM-A6DP, the host module, or hub.

1.Remove the shipping box material covering the HSIM.

2.Carefully remove the module from the shipping box. Leave the module in its non-conductive bag until you are ready to install the module.

3.Attach the antistatic wrist strap (refer to the instructions on the antistatic wrist strap package).

4.After removing the module from its non-conductive bag, visually inspect the device. If you notice any signs of damage, contact Cabletron Systems Global Call Center immediately. Refer to Section 1.7.

HSIM-A6DP User’s Guide

2-1

Image 19

Cabletron Systems HSIM-A6DP manual Chapter Installation, Unpacking The Hsim

Contents

HSIM-A6DP HSIM-A6DP User’s GuideAPIM APIMPage FCC NOTICE Only qualiﬁed personnel should perform installation proceduresHSIM-A6DP User’s Guide HSIM-A6DP User’s Guide DOC NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTHSIM-A6DP User’s Guide EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYCABLETRON SOFTWARE PROGRAM LICENSE UNITED STATES GOVERNMENT RESTRICTED RIGHTSHSIM-A6DP User’s Guide SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSSAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS LASER RADIATION AND CONNECTORSManufacturer’s Name Cabletron Systems, Inc DECLARATION OF CONFORMITYHSIM-A6DP User’s Guide Application of Council Directives 89/336/EEC 73/23/EECHSIM-A6DP User’s Guide INTRODUCTION CONTENTSINSTALLATION CHAPTERviii ContentsHSIM-A6DP User’s Guide LANVIEW LEDs ContentsAPIM SPECIFICATIONS CHAPTERHSIM-A6DP User’s Guide ContentsCHAPTER INTRODUCTION 1.2 DOCUMENT CONVENTIONS 1.1 USING THIS MANUALATM Port Interface Modules APIMs 1.4 FEATURES1.3 OVERVIEW LANVIEW Diagnostic LEDs1.6 RELATED MANUALS 1.5 SPECIFICATIONSCabletron Systems ATM Technology Guide 1.7 GETTING HELP HSIM-A6DP User’s Guide Chapter 1 Introduction2.1 UNPACKING THE HSIM CHAPTER INSTALLATION2.2 INSTALLING APIMs 6. Secure the APIM with the three screws saved in Step 2.3.1 Installing an HSIM in an Interface Module 2.3 INSTALLING AN HSIMStandoff Screws Coverplate Faceplate Mounting Screws Installing an HSIMHSIM-A6DP User’s Guide Figure 2-3 Removing the HSIM Coverplate7. Place the HSIM behind the module faceplate. See Figure 2.3.2 Installing an HSIM in a Standalone Hub In Step 9 ensure that the standoffs on the hub align with the standoff screw holes on the HSIM to prevent bending the pins CHAPTER LOCAL MANAGEMENT Table 3-1 Keyboard Conventions 3.1 LOCAL MANAGEMENT KEYBOARD CONVENTIONSChapter 3 Local Management HSIM-A6DP User’s Guide3.2.1 Selecting Local Management Menu Screen Items 3.2 NAVIGATING LOCAL MANAGEMENT SCREENS3.2.2 Exiting Local Management Screens 5. Press ENTER. The Password screen displays and the session ends 3.3 ACCESSING LOCAL MANAGEMENT APIM REDUNDANCY 3.4 THE HSIM-A6DP ATM SCREENSIGNALLING CONNECTIONS3.5 THE ATM CONNECTIONS SCREEN 3.5.1 ATM Connections Screen Fields 3.6 THE ATM CONNECTION SETUP SCREEN 3.6.1 ATM Connection Setup Screen Fields Encapsulation Type Read-Only PREVIOUS CommandNEXT Command ADD/DELETE Command3.7.1 Add/Delete Entry Screen Fields 3.7 THE ADD/DELETE ENTRY SCREENADD/MODIFY Command 3.7.2 Adding an Entry PVCEncapsulation Type Toggle 3.7.4 Deleting an Entry PVC 3.7.3 Modifying an Entry PVCFigure 3-6 The ATM Redundancy Conﬁguration Screen 3.8 THE ATM REDUNDANCY CONFIGURATION SCREEN3.8.1 ATM Redundancy Conﬁguration Screen Fields Periodic test status Toggle Active Port Read-OnlyActivation of redundant port Toggle Revert to Primary port ToggleTEST PORTS NOW Command 3.8.2 Setting the Redundancy Status3.8.3 Setting the Primary Port 3.8.4 Setting the Active Port3.8.6 Setting the Revert to Primary Port Field 3.8.5 Setting the Activation of Redundant Port Field3.8.8 Setting the Periodic Test Time 3.8.7 Setting the Periodic Test Status Field3.8.10 Using the RESET TO FACTORY DEFAULTS Command 3.8.9 Using the TEST PORTS NOW Command3.9 THE ATM LEC SCREEN LEC PROPERTIES 3.9.1 ATM LEC Screen FieldsLEC ADMINISTRATION LEC TABLE3.10 THE ATM LEC TABLE SCREEN 3.10.1 ATM LEC Table Screen Fields operational - The LEC is now fully conﬁgured, and is switching trafﬁc 3.11 THE LEC ADMINISTRATION SCREEN MAX MTU Size Toggle 3.11.1 LEC Administration Screen FieldsLEC Status Read-Only Conﬁgure LEC ToggleThis command adds the LEC to the HSIM-A6DP LEC Index 3.11.3 Conﬁguring the LEC Automatically CREATE MODE Only 3.11.2 Changing the LEC Status MODIFY MODE Only3.11.4 Conﬁguring the LEC Manually CREATE MODE Only 3.11.5 Modifying an Existing LEC 3.11.6 Deleting an Existing LEC 3.12.1 ELAN Properties Screen Fields 3.12 THE ELAN PROPERTIES SCREENThis ﬁeld displays the name of the ELAN to which this LEC belongs LECS Conﬁguration Direct VCC Read-Only LECS ATM ADDR Read-OnlyLES ATM ADDR Read-Only BUS ATM ADDR Read-Only3.13 THE LEC ARP CACHE SCREEN 3.13.1 LEC ARP CACHE Screen Fields This command opens the next series of MAC/ATM Address pairs. To access the next series of address pairs, highlight the NEXT command by using the arrow keys and pressing ENTER. The next series of MAC/ATM address pairs displays Figure 3-12 The LEC ARP Cache Search Screen 3.14 THE LEC ARP CACHE SEARCH SCREEN3.14.2 Performing a Search 3.14.1 LEC ARP Cache Search Screen FieldsWhen the search is completed, the following information displays This ﬁeld displays the name of the ELAN to which this LEC belongs 3.15 THE SIGNALLING SCREEN 3.15.1 Signaling Screen Fields UNI Q93b Status Read-Only 3.15.2 Changing the ILMI StatusRESTART UNI Command RESTART ILMI Command3.15.3 Disabling the ILMI Status 3.15.5 Restarting UNI 3.15.4 Changing the UNI Status3.15.6 Restarting the ILMI 3.15.7 Setting the UNI Version Figure 3-15 The ATM Discovery ELAN Setup Screen 3.16 THE DISCOVERY ELAN SETUP SCREENThe default ELAN does not have a name assigned to itself 3.16.1 ATM Discovery ELAN Setup Screen FieldsNEXT 3.16.2 Assigning the HSIM-A6DP to a discovery ELANSAVE PREV3. Use the arrow keys to highlight the Status field 3.18 ENABLING THE BANDWIDTH ALLOCATION MODE FEATURE 3.17 USING THE BANDWIDTH ALLOCATION MODE FEATUREFigure 3-16 The ATM Connection Screen Do not perform the following steps unless the Bandwidth Figure 3-18 The ATM Connection Setup Screen 3.19 CREATING PVCS WITH THE BANDWIDTH ALLOCATION MODE ENABLED3.19.1 ATM Connection Setup Screen Fields This ﬁeld displays the total amount of bandwidth assigned to this PVC 3.20.1 Add/Delete Entry Screen Fields 3.20 THE ADD/DELETE ENTRY SCREENIF Modiﬁable Total Bandwidth On Interface Read-Only ADD/MODIFY CommandThe Add/Delete Entry Screen Encapsulation Type Toggle3.20.2 Adding an Entry PVC 3.20.3 Modifying an Entry PVC 3.20.4 Deleting an Entry PVC 4.1 HSIM-A6DP LEDs CHAPTER LANVIEW LEDsColor Chapter 4 LANVIEW LEDsHSIM-A6DP User’s Guide Table 4-1 HSIM LEDsA.1 APIM-11 SPECIFICATIONS APPENDIX A APIM SPECIFICATIONSA.2 APIM-21 SPECIFICATIONS Figure A-3 A.3 APIM-29 SPECIFICATIONSThe APIM-29 A.4 APIM-29LR SPECIFICATIONS Receive + A.5 APIM-22 SPECIFICATIONSThe APIM-67R does not use Cell Payload Scrambling A.6 APIM-67 SPECIFICATIONSFigure A-7 The APIM-67 Figure A-6 APIM-67R Default Jumper SettingsAPIM-67 Speciﬁcations HSIM-A6DP User’s GuideHSIM-A6DP User’s Guide Appendix A APIM Speciﬁcations