Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems HSIM-A6DP manual ATM LEC Table Screen Fields

Models: HSIM-A6DP

1 100

Download 100 pages 18.73 Kb

Page 51

3.10.1 ATM LEC Table Screen Fields

The ATM LEC Table Screen

3.10.1 ATM LEC Table Screen Fields

The ATM LEC Table screen is a read-only screen that allows the user to view the status of all LECs currently conﬁgured on the HSIM-A6DP.

The following list explains each of the ATM LEC Table screen ﬁelds:

IF (Read-Only)

This ﬁeld displays the MIB-II Interface that this LEC has been assigned dynamically.

LEC Index (Read-Only)

This ﬁeld displays the Index of the LEC that was dynamically assigned.

ELAN Name (Read-Only)

This ﬁeld displays the name given the Emulated LAN (ELAN) by the user in the ELAN Administration screen (Section 3.11) or by the LECS.

LEC State (Read-Only)

This ﬁeld displays the current state of the LEC. The LEC goes through a series of initialization phases, which may result in this ﬁeld displaying different states as the initialization process proceeds. The possible states are as follows:

NOTE

In most cases, the initialization process occurs very rapidly, and the following initialization states, with the exception of “operational”, will not display.

initialState - While in initialState the LEC receives various conﬁguration parameters from the LES, such as ATM addresses, ELAN name, and maximum frame size allowed.

lecsConnect - During the lecsConnect phase, the LEC establishes a Conﬁguration Direct VCC with the LECS.

conﬁgure - The conﬁgure phase is where the LEC connects to the LES before going on the join phase.

join - During the join phase, the LEC establishes an LES Control Direct VCC with the LES. After this connection is made, the LEC is assigned a LEC Index, and the initialization process proceeds to the initialRegistration phase.

HSIM-A6DP User’s Guide

3-25

Image 51

Cabletron Systems HSIM-A6DP manual ATM LEC Table Screen Fields

Contents

HSIM-A6DP HSIM-A6DP User’s GuideAPIM APIMPage Only qualiﬁed personnel should perform installation procedures FCC NOTICEHSIM-A6DP User’s Guide HSIM-A6DP User’s Guide DOC NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTHSIM-A6DP User’s Guide EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYCABLETRON SOFTWARE PROGRAM LICENSE UNITED STATES GOVERNMENT RESTRICTED RIGHTSHSIM-A6DP User’s Guide SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSSAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS LASER RADIATION AND CONNECTORSManufacturer’s Name Cabletron Systems, Inc DECLARATION OF CONFORMITYHSIM-A6DP User’s Guide Application of Council Directives 89/336/EEC 73/23/EECHSIM-A6DP User’s Guide INTRODUCTION CONTENTSINSTALLATION CHAPTERContents viiiHSIM-A6DP User’s Guide LANVIEW LEDs ContentsAPIM SPECIFICATIONS CHAPTERHSIM-A6DP User’s Guide ContentsCHAPTER INTRODUCTION 1.2 DOCUMENT CONVENTIONS 1.1 USING THIS MANUALATM Port Interface Modules APIMs 1.4 FEATURES1.3 OVERVIEW LANVIEW Diagnostic LEDs1.5 SPECIFICATIONS 1.6 RELATED MANUALSCabletron Systems ATM Technology Guide 1.7 GETTING HELP HSIM-A6DP User’s Guide Chapter 1 Introduction2.1 UNPACKING THE HSIM CHAPTER INSTALLATION2.2 INSTALLING APIMs 6. Secure the APIM with the three screws saved in Step 2.3.1 Installing an HSIM in an Interface Module 2.3 INSTALLING AN HSIMStandoff Screws Coverplate Faceplate Mounting Screws Installing an HSIMHSIM-A6DP User’s Guide Figure 2-3 Removing the HSIM Coverplate7. Place the HSIM behind the module faceplate. See Figure 2.3.2 Installing an HSIM in a Standalone Hub In Step 9 ensure that the standoffs on the hub align with the standoff screw holes on the HSIM to prevent bending the pins CHAPTER LOCAL MANAGEMENT Table 3-1 Keyboard Conventions 3.1 LOCAL MANAGEMENT KEYBOARD CONVENTIONSChapter 3 Local Management HSIM-A6DP User’s Guide3.2 NAVIGATING LOCAL MANAGEMENT SCREENS 3.2.1 Selecting Local Management Menu Screen Items3.2.2 Exiting Local Management Screens 5. Press ENTER. The Password screen displays and the session ends 3.3 ACCESSING LOCAL MANAGEMENT APIM REDUNDANCY 3.4 THE HSIM-A6DP ATM SCREENSIGNALLING CONNECTIONS3.5 THE ATM CONNECTIONS SCREEN 3.5.1 ATM Connections Screen Fields 3.6 THE ATM CONNECTION SETUP SCREEN 3.6.1 ATM Connection Setup Screen Fields Encapsulation Type Read-Only PREVIOUS CommandNEXT Command ADD/DELETE Command3.7.1 Add/Delete Entry Screen Fields 3.7 THE ADD/DELETE ENTRY SCREEN3.7.2 Adding an Entry PVC ADD/MODIFY CommandEncapsulation Type Toggle 3.7.4 Deleting an Entry PVC 3.7.3 Modifying an Entry PVCFigure 3-6 The ATM Redundancy Conﬁguration Screen 3.8 THE ATM REDUNDANCY CONFIGURATION SCREEN3.8.1 ATM Redundancy Conﬁguration Screen Fields Periodic test status Toggle Active Port Read-OnlyActivation of redundant port Toggle Revert to Primary port ToggleTEST PORTS NOW Command 3.8.2 Setting the Redundancy Status3.8.3 Setting the Primary Port 3.8.4 Setting the Active Port3.8.6 Setting the Revert to Primary Port Field 3.8.5 Setting the Activation of Redundant Port Field3.8.8 Setting the Periodic Test Time 3.8.7 Setting the Periodic Test Status Field3.8.10 Using the RESET TO FACTORY DEFAULTS Command 3.8.9 Using the TEST PORTS NOW Command3.9 THE ATM LEC SCREEN LEC PROPERTIES 3.9.1 ATM LEC Screen FieldsLEC ADMINISTRATION LEC TABLE3.10 THE ATM LEC TABLE SCREEN 3.10.1 ATM LEC Table Screen Fields operational - The LEC is now fully conﬁgured, and is switching trafﬁc 3.11 THE LEC ADMINISTRATION SCREEN MAX MTU Size Toggle 3.11.1 LEC Administration Screen FieldsLEC Status Read-Only Conﬁgure LEC ToggleThis command adds the LEC to the HSIM-A6DP LEC Index 3.11.3 Conﬁguring the LEC Automatically CREATE MODE Only 3.11.2 Changing the LEC Status MODIFY MODE Only3.11.4 Conﬁguring the LEC Manually CREATE MODE Only 3.11.5 Modifying an Existing LEC 3.11.6 Deleting an Existing LEC 3.12.1 ELAN Properties Screen Fields 3.12 THE ELAN PROPERTIES SCREENThis ﬁeld displays the name of the ELAN to which this LEC belongs LECS Conﬁguration Direct VCC Read-Only LECS ATM ADDR Read-OnlyLES ATM ADDR Read-Only BUS ATM ADDR Read-Only3.13 THE LEC ARP CACHE SCREEN 3.13.1 LEC ARP CACHE Screen Fields This command opens the next series of MAC/ATM Address pairs. To access the next series of address pairs, highlight the NEXT command by using the arrow keys and pressing ENTER. The next series of MAC/ATM address pairs displays Figure 3-12 The LEC ARP Cache Search Screen 3.14 THE LEC ARP CACHE SEARCH SCREEN3.14.2 Performing a Search 3.14.1 LEC ARP Cache Search Screen FieldsWhen the search is completed, the following information displays This ﬁeld displays the name of the ELAN to which this LEC belongs 3.15 THE SIGNALLING SCREEN 3.15.1 Signaling Screen Fields UNI Q93b Status Read-Only 3.15.2 Changing the ILMI StatusRESTART UNI Command RESTART ILMI Command3.15.3 Disabling the ILMI Status 3.15.4 Changing the UNI Status 3.15.5 Restarting UNI3.15.6 Restarting the ILMI 3.15.7 Setting the UNI Version Figure 3-15 The ATM Discovery ELAN Setup Screen 3.16 THE DISCOVERY ELAN SETUP SCREENThe default ELAN does not have a name assigned to itself 3.16.1 ATM Discovery ELAN Setup Screen FieldsNEXT 3.16.2 Assigning the HSIM-A6DP to a discovery ELANSAVE PREV3. Use the arrow keys to highlight the Status field 3.18 ENABLING THE BANDWIDTH ALLOCATION MODE FEATURE 3.17 USING THE BANDWIDTH ALLOCATION MODE FEATUREFigure 3-16 The ATM Connection Screen Do not perform the following steps unless the Bandwidth Figure 3-18 The ATM Connection Setup Screen 3.19 CREATING PVCS WITH THE BANDWIDTH ALLOCATION MODE ENABLED3.19.1 ATM Connection Setup Screen Fields This ﬁeld displays the total amount of bandwidth assigned to this PVC 3.20 THE ADD/DELETE ENTRY SCREEN 3.20.1 Add/Delete Entry Screen FieldsIF Modiﬁable Total Bandwidth On Interface Read-Only ADD/MODIFY CommandThe Add/Delete Entry Screen Encapsulation Type Toggle3.20.2 Adding an Entry PVC 3.20.3 Modifying an Entry PVC 3.20.4 Deleting an Entry PVC 4.1 HSIM-A6DP LEDs CHAPTER LANVIEW LEDsColor Chapter 4 LANVIEW LEDsHSIM-A6DP User’s Guide Table 4-1 HSIM LEDsA.1 APIM-11 SPECIFICATIONS APPENDIX A APIM SPECIFICATIONSA.2 APIM-21 SPECIFICATIONS A.3 APIM-29 SPECIFICATIONS Figure A-3The APIM-29 A.4 APIM-29LR SPECIFICATIONS Receive + A.5 APIM-22 SPECIFICATIONSThe APIM-67R does not use Cell Payload Scrambling A.6 APIM-67 SPECIFICATIONSFigure A-7 The APIM-67 Figure A-6 APIM-67R Default Jumper SettingsAPIM-67 Speciﬁcations HSIM-A6DP User’s GuideHSIM-A6DP User’s Guide Appendix A APIM Speciﬁcations