Manuals / Cabletron Systems / Computer Equipment / Network Router

Cabletron Systems NBR-420 Page, NBR-SERIES Installation Guide, Flash, Ldram, Brim Port F

Models: NBR-620 NBR-220 NBR-420

1 73

Download 73 pages 57.23 Kb

Page 21

FLASH

Chapter 3: Installation

FLASH	LDRAM			BRIM (PORT F)
FLASH	SDRAM				BRIM (PORT E)

NVRAM

RESET SWITCH

NBR FRONT PANEL

MODE SWITCH BANK

OFF ON

1

2

3

4

5

6

7

8

Cabletron Use Only

Cabletron Use Only

Cabletron Use Only

Cabletron Use Only

Baud Rate Default Switch (Off=9600, On=2400)

Forced Download Switch (This switch forces image file downloads.) Cabletron Use Only

Password Default Switch (This switch clears passwords stored in NVRAM.)

1092_07

Figure 3-2 Switch, BRIM, and SIMM Locations

Page 3-4

NBR-SERIES Installation Guide

Image 21

Cabletron Systems NBR-420 Page, NBR-SERIES Installation Guide, 2 Switch, BRIM, and SIMM Locations, Flash, Ldram, Sdram

Contents

PORT B NBR-220, NBR-420, AND NBR-620 INSTALLATION GUIDEPORT A PORT FFCC NOTICE NBR-SERIES Installation GuideDOC NOTICE NBR-SERIES Installation GuideVCCI NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTNBR-SERIES Installation Guide EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYCABLETRON SOFTWARE PROGRAM LICENSE UNITED STATES GOVERNMENT RESTRICTED RIGHTSDECLARATION OF CONFORMITY NBR-SERIES Installation GuideCHAPTER 2 CONTROLS AND INDICATORS CONTENTSINSTALLATION NBR-SERIES Installation GuideTROUBLESHOOTING ContentsAPPENDIX A NBR SPECIFICATIONS EPIM SPECIFICATIONSNBR-SERIES Installation Guide ContentsAPPENDIX D ADDITIONAL INFORMATION INDEXNBR-SERIES Installation Guide CHAPTER INTRODUCTIONPage Figure 1-1 The NBR-SERIES of Network Products1.1 USING THIS MANUAL 1.2 NBR FEATURES The NBR provides IETF MIB support, which includes the following The NBR supports the following spanning tree protocols 802.1d DECnet 1.3 CONVENTIONS USED IN THIS DOCUMENT Cabletron Systems Routing Services Conﬁguration Guide1.4 RELATED MANUALS Cabletron Systems BRIM User’s Guides1.5 GETTING HELP anonymousyour email address Figure 2-1 The NBR-SERIES of Network Products CHAPTER CONTROLS AND INDICATORS2.2 RESET BUTTON 2.1 LANVIEW LEDs2.3 LCD DISPLAY 3.1 UNPACKING THE NBR CHAPTER INSTALLATION3.2.1 Removing Chassis Cover 3.2 PREPARING THE NBR FOR INSTALLATIONTo remove the chassis cover, perform the following steps see Figure NBR-SERIES Installation Guide Chapter 3 InstallationFigure 3-2 Switch, BRIM, and SIMM Locations NVRAM RESET SWITCH NBR FRONT PANEL MODE SWITCH BANK3.2.2 Setting Mode Switches 3.2.3 Setting NVRAM Reset Switch 3.2.4.1 Installing FLASH SIMMs 3.2.4 Installing SIMM UpgradesInstall a FLASH SIMM as follows 3.2.4.2 Installing LDRAM and SDRAM SIMMs 3.2.5 Adding/Replacing EPIMsFigure 3-4 Installing an LDRAM or SDRAM SIMM Install an EPIM as follows 3.2.6 Adding/Replacing BRIMs3. Fasten the EPIM to the NBR using the mounting screws Chapter 3 Installation3.2.7 Testing the NBR Ensure that you select a location within reach of the network cabling 3.3 INSTALLING THE NBR3.3.1 Attaching the Strain-Relief Bracket 3.3.2 Rack Mounting the NBR 3.4 CONNECTING THE NBR TO THE POWER SOURCE 3.3.3 Free-Standing InstallationPWR LED on, indicating that the NBR is receiving power 3.5.1 Connecting a Twisted Pair Segment to an EPIM-T 3.5 CONNECTING THE NBR TO THE NETWORKConnect an EPIM-T to a Twisted Pair Segment as follows 3.5.2 Connecting an AUI Cable to an EPIM-X 3.5.3 Connecting a Fiber Optic Cable to an EPIM-F1/F2 or EPIM-F3 connectors do not need alignment sleevesA full alignment sleeve damages the receive port. SMA F1/F2 ST Connectors F1/F2 SMA 906 Connectors w Half Alignment Sleeves SMA 905 Connectors F3 ST ConnectorsFigure 3-15 The EPIM-F1/F2 and EPIM-F3 3.5.4 Connecting a Thin-Net Segment to an EPIM-C 3.5.5 Connecting an AUI Cable to an EPIM-A Connect an EPIM-A to an external network segment as follows 4.1 USING LANVIEW CHAPTER TROUBLESHOOTINGNBR-SERIES Installation Guide Chapter 4 TroubleshootingError Condition PageNBR-SERIES Installation Guide Using LANVIEWError Condition PageChapter 4 Troubleshooting 4.2 TROUBLESHOOTING CHECKLISTNBR-SERIES Installation Guide Table 4-2 Troubleshooting ChecklistNBR-SERIES Installation Guide Troubleshooting ChecklistTable 4-2 Troubleshooting Checklist Continued Problem4.3 USING THE LCD 4.3.1 Unsaved Initialization Messages 4.3.2 Static System MessagesTo Display the Messages Jump to Alarm messages From the last Static System messageAutomatic 20-second exit From the product name display 4.3.3 Alarm MessagesFrom a Static System message display Jump to Saved System messagesChapter 4 Troubleshooting 4.3.4 Saved System MessagesNBR-SERIES Installation Guide To Display MessagesFrom any displayed System message From an Alarm message displayFrom the product name display Automatic 20-second exit4.4 USING THE RESET BUTTON 4.3.5 Failure or Error MessagesA.1 OPERATING SPECIFICATIONS APPENDIX A NBR SPECIFICATIONSCOM 1 PORT PINOUTS COM PORT PINOUTSCOM 2 PORT PINOUTS COM PORT NBR-220 Only PINOUTSA.3 PHYSICAL PROPERTIES A.6 POWER SUPPLY REQUIREMENTSA.4 ENVIRONMENTAL REQUIREMENTS A.5 CERTIFICATIONAPPENDIX B EPIM SPECIFICATIONS B.1 EPIM SPECIFICATIONSB.2 EPIM-T Appendix B EPIM Speciﬁcations B.3 EPIM-F1/F2Figure B-3 EPIM-F3 B.4 EPIM-F3The transmitter power levels given above are Peak Power Levels after optical overshoot. Use a Peak Power Meter to compare the values given above to those measured on any particular port. To measure power levels with an Average Power Meter, add 3 dBm to the average power measurement to compare the average power values measured to the values listed above i.e., -33.5 dBm average + 3 dBm = -30.5 dBm peak B.5 EPIM-C Connector TypeGrounding Figure B-5 EPIM-A and EPIM-X, AUI Port B.6 EPIM-A AND EPIM-XTable B-1 DB15 PinoutsAPPENDIX C NETWORK PLANNING AND CONFIGURATION C.1 NETWORK CABLE REQUIREMENTSC.1.1 10BASE-T Twisted Pair Network Appendix C Network Planning and Conﬁguration C.1.2 Multimode Fiber Optic Network C.1.3 Single Mode Fiber Optic Network C.1.4 Thin-Net Network C.3 THE NBR AS A MULTIPORT ROUTER C.2 TRANSCEIVER REQUIREMENTSC.4 THE NBR-420/NBR-620 AND BRIMS Figure C-1 The NBR-620 and BRIMsD.1 NBR OVERVIEW APPENDIX D ADDITIONAL INFORMATIOND.3 CHANNELS E AND F D.2 ETHERNET CHANNELS A, B, C, AND DD.4 BRIDGING FUNCTIONALITY INDEX NBR-SERIES Installation GuideIndex-1 GERMAN POWER SUPPLY CORDSPANISH FRENCH