Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems SEHI-22FL manual Connect the console cable to the SEHI as follows

Models: SEHI-22FL

1 85

Download 85 pages 32.83 Kb

Page 53

Connect the console cable to the SEHI as follows:

Chapter 7: Local Management

Console Cable Conﬁguration

Use the RJ45 Cable Kit provided with the SEHI-ACCY-KIT package to attach the management terminal to the SEHI COM port as shown in Figure 7-1.

Connect the console cable to the SEHI as follows:

1.Attach the male RJ45 connector to the COM port of the SEHI.

2.Attach the female end (25-pin or 9-pin, as applicable) to the COM port on the terminal.

	HubSTACK 10BASE-T HUB WITH LANVIEW®	EPIM-2
	SEHI-24
	COM	EPIM-1
	COM RJ45 Port	Management Terminal
	Console Cable	Management Terminal
	Console Cable

COM Port

09162_17

Figure 7-1 Management Terminal Connection

7-4	SEHI User’s Guide

Image 53

Cabletron Systems SEHI-22FL manual Connect the console cable to the SEHI as follows

Contents

SEHI-22FL INTELLIGENT STACKABLE HUB USER’S GUIDE SEHI User’s Guide DOC NOTICE FCC NOTICEVCCI NOTICE SEHI User’s GuideCABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYCABLETRON SOFTWARE PROGRAM LICENSE SEHI User’s GuideSEHI User’s Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTSCHAPTER 2 SEHI FEATURES AND OPTIONS CONTENTSCHAPTER 3 INSTALLATION REQUIREMENTS AND SPECIFICATIONSINSTALLATION ContentsCHAPTER 5 CONNECTING TO THE NETWORK TROUBLESHOOTINGAPPENDIX B IMAGE FILE DOWNLOAD USING OIDs ContentsAPPENDIX A EPIM INFORMATIONCHAPTER INTRODUCTION 1.1 USING THIS MANUAL1.2 DOCUMENT CONVENTIONS 1.4 RELATED MANUALS 1.3 GETTING HELPanonymous your email addressRESET Button CHAPTER SEHI FEATURES AND OPTIONSPower Supply ON/OFF Switch2.1 SEHI OVERVIEW 2.2 SEHI FEATURESRepeater Functionality FLASH EEPROMs2.4 REMOTE NETWORK MANAGEMENT CAPABILITIES 2.3 STACKABLE CAPABILITIESEthernet Port Interface Modules EPIMs 2.5 OPTIONAL FEATURESHubSTACK Interconnect Cables Rack Mount Hardware3.1 CABLE SPECIFICATIONS CHAPTER INSTALLATION REQUIREMENTS AND SPECIFICATIONS3.1.2 10BASE-FL Fiber Optic Network Requirements 3.1.1 HubSTACK Interconnect Cable RequirementsFiber Optic Budget and Propagation Delay AttenuationDelay 3.1.3 10BASE-T UTP and STP Cable SpeciﬁcationsLength Insertion Loss3.2 NETWORK PORT SPECIFICATIONS 3.4 TRANSCEIVER REQUIREMENTS 3.3 COM PORT REQUIREMENTSDelay Time Start of Packets Speciﬁcations 3.5 OPERATING SPECIFICATIONSDelay Times JAM Speciﬁcations System Speciﬁcations3.6 POWER SUPPLY REQUIREMENTS 3.9 PHYSICAL SPECIFICATIONS 3.8.1 Safety3.7 ENVIRONMENTAL REQUIREMENTS 3.8 AGENCY APPROVALS4.1 UNPACKING THE SEHI CHAPTER INSTALLATIONChapter 4 Installation 4.2 PRE-INSTALLATION TEST4.3 INSTALLING THE SEHI clearance on either side and the back of the unit 4.3.1 Tabletop or Shelf InstallationIn order to allow for proper cooling, there must be a two-inch 4.3.2 Rackmount Installation Rack Mounting the SEHI Figure 4-4 Installing the Rack Mounting BracketsChapter 4 Installation 4.3.3 Stacking the SEHIFigure 4-5 Installing the SEHI in the Rack The cooling fans at the rear panel of the SEHI must haveTo stack SEH non-intelligent hubs together, proceed as follows 4.4 CONNECTING THE SEHI TO THE POWER SOURCE 4.5 ADDING/REPLACING EPIMS 5.1.1 Connecting Network Ports CHAPTER CONNECTING TO THE NETWORK5.1 CONNECTING THE SEHI TO THE NETWORK the ends come in contact with dust, dirt, or other contaminants Chapter 5 Connecting to the NetworkDo not touch the ends of the ﬁber optic strands, and do not let 3. Attach the fiber labeled 2 to the applicable TX port, on the SEHI 5.1.2 Connecting a UTP Segment to an EPIM-T SEHI User’s Guide 5.1.3 Connecting a Fiber Segment to an EPIM-F1/F2/F3Connecting the SEHI to the Network 3. Attach the fiber labeled 2 to the applicable TX port on the module SMA 905 Connectors F3 ST Connectors F1/F2 ST Connectors F1/F2 SMA 906 Connectors w Half Alignment SleevesConnecting the SEHI to the Network SEHI User’s Guide5.1.4 Connecting a Thin Coaxial Segment to an EPIM-C Connecting the SEHI to the Network 5.1.5 Connecting an AUI Cable to an EPIM-AEnsure that the Signal Quality Error SQE or “heartbeat” test function is disabled on the external transceiver connected tob. Check the cable for continuity ON Position 5.1.6 Connecting an AUI Cable to an EPIM-XToward Back of EPIM5.2 FINISHING THE INSTALLATION 6.1 INSTALLATION CHECKOUT CHAPTER TROUBLESHOOTING6.2 USING LANVIEW SEHI-22FL 6.3 USING THE RESET BUTTON 6.4 SETTING THE NVRAM SWITCH CHAPTER LOCAL MANAGEMENT Chapter 7 Local Management 7.1 LOCAL MANAGEMENT KEYBOARD CONVENTIONSSEHI User’s Guide Table 7-1 Keyboard Conventions7.2 MANAGEMENT TERMINAL SETUP Connect the console cable to the SEHI as follows Management Terminal Setup Parameters 7.3 ACCESSING LOCAL MANAGEMENT Figure 7-3 Feature Selection Screen 7.4 THE FEATURE SELECTION SCREENCOMMUNITY NAME 7.5 THE COMMUNITY NAME TABLE SCREENEditing the Community Name Field write access to Local Management. Super-UserACCESS 7.6 THE CONFIGURATION SCREEN The following sections explain each ﬁeld on the Conﬁguration screen Use the following steps to set the IP Address Using the Port Enable Override Setting the Default Gateway7.7 THE TRAP TABLE SCREEN Use the following steps to conﬁgure the Trap table 7.8 THE SNMP TOOLS SCREEN Allows the user to retrieve MIB objects using SNMP protocol Getting the Next OID Setting an OIDGetting Individual OIDs 5. Press ENTER. “DATA” appears Exiting the SNMP Tools Screen 7.9 THE DEVICE STATISTICS SCREENCycling Through OIDs The following sections describe Device Statistics screen ﬁelds This command lets the user enable the selected port To select a module or port Exiting the Device Statistics Screen Using the DISABLE PORT CommandA.1.1 EPIM-T A.1 EPIM SPECIFICATIONSAPPENDIX A EPIM INFORMATION Appendix A EPIM Information A.1.2 EPIM-F1 and EPIM-F2A.1.3 EPIM-F3 Grounding A.1.4 EPIM-CConnector Type Figure A-5 The EPIM-A and EPIM-X A.1.5 EPIM-A and EPIM-X AUI PortAPPENDIX B IMAGE FILE DOWNLOAD USING OIDs B.1 SETTING UP A UNIX WORKSTATION AS A TFTP SERVER B.2 STANDARD TFTP DOWNLOAD Table B-1 Standard TFTP Download Procedure Appendix B Image File Download Using OIDsSEHI User’s Guide StepNumerics INDEXSEHI User’s Guide Index-1SEHI User’s Guide IndexIndex-2 GERMAN POWER SUPPLY CORDSPANISH FRENCH