Casio DT-X5 Series Connecting Multiple Dual Battery Chargers

E-66

Using the Dual Battery Charger

Connecting Multiple Dual Battery Chargers

You can connect up to three Dual Battery Chargers. Doing so makes it possible to supply

power to all the Dual Battery Chargers using the AC adaptor.

1.As shown in the illustrations below, remove the connector covers of the Dual Battery

Chargers you want to connect to each other.

2.Connect the two Dual Battery Chargers as

shown below.

3.Turn over the connected Dual Battery

Chargers and attach a connection bracket,

securing it in place with screws.

You can repeat the above steps to connect

up to three Dual Battery Chargers.

Connector cover

DT-X5_E_P59_69.p65 04.7.14, 6:05 PM66

Contents

Main Handheld Terminal Series Users Guide PN410388-002 Page Safety Precautions Page Page E-4 Operation of Wireless Data Communication Function Interference with the Operation of Other Equipment (Using Wireless Data Communication Function) E-5 Alkaline Battery Handling Precautions Danger E-6 E-7 Optional Lithium-ion Battery Pack Danger E-8 E-9 AC Power Supply Page E-11 Operating Precautions E-12 Important Warranty and After Service E-13 NOTICE FCC WARNING Peripherals and Cables E-14 certify and declare under our sole responsibility that the following equipments: Important We, the undersigned. E-15 E-16 Contents E-17 E-18 Before Getting Started When unpacking, make sure that all items are included. E-19 Install the main battery When Using the AA size Alkaline Batteries (DT-X5M10E/DT-X5M30E/ DT-X5M30U only) E-20 When Using the Battery Pack E-21 Turning On the Power Handheld Terminal System Configuration Page Page E-25 General Guide E-26 E-27 Replacing the Battery This guide uses the following terms to refer to the batteries. Replacing the Battery Pack Always keep backup copies of all important data! E-28 Replacing the AA size Alkaline Batteries (DT-X5M10E/DT-X5M30E/ DT-X5M30U only) E-29 To replace the battery pack E-30 Page E-32 Removing and Installing the Alkaline Battery Holder (DT-X5M10E/DT-X5M30E/DT-X5M30U only) Removal Procedure E-33 Installation Procedure Attaching the Wrist Strap E-35 Configuring Handheld Terminal Settings Adjusting Display Contrast Turning Backlight On and Off E-36 Using the Laser Scanner (DT-X5M10E/DT-X5M10R only) E-37 Warning Label Warning! Never look directly into the laser light. Bar Code Scanning Position Margin Margin Good Good Good Bad Bad Bad Bad E-38 Using the C-MOS Imager (DT-X5M30E/DT-X5M30R/DT-X5M30U/DT-X5M30UR only) Warning Label E-40 Adjusting Laser Emission Width (DT-X5M10/DT-X5M10R only) Page E-42 Performing Communication IR Communication E-43 BluetoothTM Communication E-44 Resetting the Handheld Terminal Reset and Full Reset (Memory Initialization) Reset Performing a Full Reset (Initialization) To perform a reset To perform a full reset E-46 DT-X5 Specifications E-47 E-48 E-49 Using the Bridge Satellite Cradle (HA-A61IO)/ Bridge Basic Cradle (HA-A60IO) E-50 E-51 Connecting the AC Adaptor and Connecting to Computer E-52 E-53 Removing the Fall Protector E-54 Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO) Configuring DIP Switch Settings (HA-A61IO) Not used (Always off) Not used (Always off) Host Computer Interface Daisy Chain Connection Type Bridge Satellite Cradle Data Rate E-55 Using Wall Mount Unit Page E-57 Connecting Multiple Bridge Satellite Cradles (HA-A61IO) E-58 Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO) Specifications E-59 Using the Cradle-type Battery Charger E-60 E-61 Connecting the AC Adaptor for Cradle-type Battery Charger Important ! E-62 Using Wall Mount Unit Removing the Fall Protector Cradle-type Battery Charger (HA-A30CHG) Specifications E-63 Using the Dual Battery Charger E-64 Page E-66 Connecting Multiple Dual Battery Chargers E-67 Dual Battery Charger (DT-5022CHG) Specifications E-68 Using Rechargeable Battery Pack Battery Pack Specifications Large-capacity Battery Pack Specifications