Cisco Systems 1900 Series Safety with Electricity

2-2

Cisco 1900 Series Hardware Installation

OL-19084-02

Chapter 2 Preparing for Router Installation

Safety Recommendations

Warning

Read the installation instructions before connecting the system to the power source.

Statement 1004

Warning

Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)

that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not

operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement

1029

Warning

To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the

handles on modules (such as power supplies, fans, or cards); these types of handles are not designed

to support the weight of the unit.

Statement 1032

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Safety with Electricity

Follow these guidelines when working on equipment powered by electricity.

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning

Read the installation instructions before connecting the system to the power source.

Statement 1004

Warning

When installing or replacing the unit, the ground connection must always be made first and

disconnected last.

Statement 1046

• Locate the emergency power-off switch in the room in which you are working. Then, if an electrical

accident occurs, you can quickly turn off the power.

• Disconnect all power before doing the following:

–

Installing or removing a chassis

–

Working near power supplies

–

Removing the top cover of a chassis

• Look carefully for possible hazards in your work area, such as moist floors, ungrounded power

extension cables, frayed power cords, and missing safety grounds.

• Do not work alone if hazardous conditions exist.

• Never assume that power is disconnected from a circuit. Always check.

• Never open the enclosure of the router’s internal power supply.

Contents

Main Page CONTENTS OL-19084-03 i Page Page Page Preface Objectives Audience Organization Conventions ix damage or loss of data. the paragraph. x xi xii Page xiv Related Documentation Searching within Cisco Documents Obtaining Documentation and Submitting a Service Request Overview of the Router Safety Warnings Safety Warnings for Finland, Norway and Sweden Chassis Views Page 123 4 5 Hardware Features Product Serial Number Location Cisco Product Identification Tool Built-In Interfaces Removable, Interchangeable, and Optional Modules Memory LED Indicators Page Chassis Ventilation Real-Time Clock Chassis Security Wireless LAN Connectivity Baud Reset Button Interface Numbering Specifications Page Page Page Regulatory Compliance Preparing for Router Installation Safety Recommendations General Guidelines Safety with Electricity Preventing Electrostatic Discharge Damage General Site Requirements Power Supply Considerations Site Environment Site Configuration Wireless LAN Considerations Inspecting the Router Installation Checklist Site Log Required Tools and Equipment for Installation and Maintenance Page Cable Information and Specifications for Cisco 1900 Series Routers Console and Auxiliary Port Considerations About Console and Auxiliary Ports Console Port Connections EIA/TIA-232 Port USB Serial Console Auxiliary Port Connections Preparing to Connect to a Network Ethernet Connections Serial Connections About Serial Connections Configuring Serial Connections Serial DTE or DCE Devices Signaling Standards Supported Transmission Speeds and Distance Limitations Asynchronous/Synchronous Serial Module Baud Rates ISDN BRI Connections CSU/DSU Connections Installing and Connecting the Router About Modules Internal Modules Plug-In Modules Safety Warnings Safety Warnings for Finland, Norway and Sweden Setting Up the Chassis Chassis Airflow Diagram Setting the Chassis on a Desktop Chassis Grounding Wall-Mounting the Chassis Page Page Rack-Mounting the Chassis Attaching Rack-Mount Brackets to Cisco 1900 Series Routers 4-8 Figure 4-5 Bracket Installation for Front Mounting the Cisco 1905 and Cisco 1921 ISRs Figure 4-6 shows how to attach the brackets to the sides of the router with the back panel forward. Figure 4-6 Bracket Installation for Back Mounting the Cisco 1905 and Cisco 1921 ISRs Figure 4-7 shows how to attach the brackets to the sides of the router with the front panel forward. Installing the Chassis Ground Connection Page Connecting WAN and LAN Cables Safety Messages 4-12 Ports and Cabling Connection Procedures and Precautions Connecting to a Console Terminal or Modem Connecting to the Console Port with Microsoft Windows Page Connecting to the Console Port with Mac OS X Connecting to the Console Port with Linux Installing the Cisco Microsoft Windows USB Device Driver Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco USB Driver Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Using the Add Remove Programs Utility Using the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB Driver Connecting to the Auxiliary Port Connecting Power Connecting to AC Power Connecting to DC Power DC Wiring Requirements for Cisco 1900 Series Routers Cisco 1900 Series Router Wiring Procedure for DC Input 4-24 Page Page Configuring the Router Powering up the Router Checklist Before Powering Up the Cisco Router Powering Up the Cisco Router Verifying the Front Panel LED Indications Performing the Initial Configuration on the Router Using the Cisco Setup Command Facility Page 5-5 Step 9 Select one of the available interfaces for connecting the router to the management network: Step 10 Respond to the following prompts as appropriate for your network: The system creates the following configuration command script: Step 11 Respond to the following prompts. Select 2 to save the initial configuration: Using Cisco Configuration Professional Express Using the Cisco CLIManual Configuration Initial CLI Configuration Configuring the Router Hostname Configuring the Enable and Enable Secret Passwords Restrictions Configuring the Console Idle Privileged EXEC Timeout Page Configuring Gigabit Ethernet Interfaces Page Specifying a Default Route or Gateway of Last Resort Configuring IP Routing and IP Protocols IP Routing Default Routes Default Network Gateway of Last Resort 5-16 Command or Action Purpose Specifying a Default Route: Example Sample Output for the show ip route Command Step 4 ip route dest-prefix mask next-hop-ip-address Configuring Virtual Terminal Lines for Remote Console Access Example What to Do Next Configuring the Auxiliary Line Verifying Network Connectivity Prerequisites Page Saving Your Router Configuration Saving Backup Copies of Configuration and System Image Page Verifying the Initial Configuration Page Getting Software Licenses for the Router Activating a New Software Package or Feature RMA License Transfer Additional Information