Manuals / Brands / Computer Equipment / Network Router / Cisco Systems / Computer Equipment / Network Router

Cisco Systems 1900 Series 5-5, The system creates the following configuration command script:, The system displays the user prompt:, user EXEC prompt

1 102

Download 102 pages, 4.5 Mb

5-5

Cisco 1900 Series Hardware Installation

OL-19084-02

Chapter 5 Configuring the Router

Performing the Initial Configuration on the Router

Current interface summary

Interface IP-Address OK? Method Status Protocol

GigabitEthernet0/0 unassigned YES NVRAM administratively down down

GigabitEthernet0/1 10.10.10.12 YES DHCP up up

GigabitEthernet0/2 unassigned YES NVRAM administratively down down

SSLVPN-VIF0 unassigned NO unset up

Any interface listed with OK? value "NO" does not have a valid configuration

Step 9 Select one of the available interfaces for connecting the router to the management network:

Enter interface name used to connect to the management network from the above interface

summary: gigabitethernet0/1

Step 10 Respond to the following prompts as appropriate for your network:

Configuring interface GigabitEthernet0/1:

Configure IP on this interface? [yes]: yes

IP address for this interface [10.10.10.12]:

Subnet mask for this interface [255.0.0.0] : 255.255.255.0

Class A network is 10.0.0.0, 24 subnet bits; mask is /24

The system creates the following configuration command script:

hostname myrouter

enable secret 5 $1$t/Dj$yAeGKviLLZNOBX0b9eifO0 enable password cisco123 line vty 0 4

password cisco snmp-server community public !

no ip routing

!

interface GigabitEthernet0/0

shutdown

no ip address

!

interface GigabitEthernet0/1

no shutdown

ip address 10.10.10.12 255.255.255.0

!

interface GigabitEthernet0/2

shutdown

no ip address

!

end

Step 11 Respond to the following prompts. Select 2 to save the initial configuration:

[0] Go to the IOS command prompt without saving this config.

[1] Return back to the setup without saving this config.

[2] Save this configuration to nvram and exit.

Enter your selection [2]: 2

Building configuration...

Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started! RETURN

The system displays the user prompt:

myrouter>

Step 12 The facility prompts you to save the configuration. Enter yes to save the configuration and return to the

user EXEC prompt (Router>).

Use this configuration? {yes/no} : yes

Contents

Main Page CONTENTS OL-19084-03 i Page Page Page Preface Objectives Audience Organization Conventions ix damage or loss of data. the paragraph. x xi xii Page xiv Related Documentation Searching within Cisco Documents Obtaining Documentation and Submitting a Service Request Overview of the Router Safety Warnings Safety Warnings for Finland, Norway and Sweden Chassis Views Page 123 4 5 Hardware Features Product Serial Number Location Cisco Product Identification Tool Built-In Interfaces Removable, Interchangeable, and Optional Modules Memory LED Indicators Page Chassis Ventilation Real-Time Clock Chassis Security Wireless LAN Connectivity Baud Reset Button Interface Numbering Specifications Page Page Page Regulatory Compliance Preparing for Router Installation Safety Recommendations General Guidelines Safety with Electricity Preventing Electrostatic Discharge Damage General Site Requirements Power Supply Considerations Site Environment Site Configuration Wireless LAN Considerations Inspecting the Router Installation Checklist Site Log Required Tools and Equipment for Installation and Maintenance Page Cable Information and Specifications for Cisco 1900 Series Routers Console and Auxiliary Port Considerations About Console and Auxiliary Ports Console Port Connections EIA/TIA-232 Port USB Serial Console Auxiliary Port Connections Preparing to Connect to a Network Ethernet Connections Serial Connections About Serial Connections Configuring Serial Connections Serial DTE or DCE Devices Signaling Standards Supported Transmission Speeds and Distance Limitations Asynchronous/Synchronous Serial Module Baud Rates ISDN BRI Connections CSU/DSU Connections Installing and Connecting the Router About Modules Internal Modules Plug-In Modules Safety Warnings Safety Warnings for Finland, Norway and Sweden Setting Up the Chassis Chassis Airflow Diagram Setting the Chassis on a Desktop Chassis Grounding Wall-Mounting the Chassis Page Page Rack-Mounting the Chassis Attaching Rack-Mount Brackets to Cisco 1900 Series Routers 4-8 Figure 4-5 Bracket Installation for Front Mounting the Cisco 1905 and Cisco 1921 ISRs Figure 4-6 shows how to attach the brackets to the sides of the router with the back panel forward. Figure 4-6 Bracket Installation for Back Mounting the Cisco 1905 and Cisco 1921 ISRs Figure 4-7 shows how to attach the brackets to the sides of the router with the front panel forward. Installing the Chassis Ground Connection Page Connecting WAN and LAN Cables Safety Messages 4-12 Ports and Cabling Connection Procedures and Precautions Connecting to a Console Terminal or Modem Connecting to the Console Port with Microsoft Windows Page Connecting to the Console Port with Mac OS X Connecting to the Console Port with Linux Installing the Cisco Microsoft Windows USB Device Driver Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco USB Driver Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Using the Add Remove Programs Utility Using the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB Driver Connecting to the Auxiliary Port Connecting Power Connecting to AC Power Connecting to DC Power DC Wiring Requirements for Cisco 1900 Series Routers Cisco 1900 Series Router Wiring Procedure for DC Input 4-24 Page Page Configuring the Router Powering up the Router Checklist Before Powering Up the Cisco Router Powering Up the Cisco Router Verifying the Front Panel LED Indications Performing the Initial Configuration on the Router Using the Cisco Setup Command Facility Page 5-5 Step 9 Select one of the available interfaces for connecting the router to the management network: Step 10 Respond to the following prompts as appropriate for your network: The system creates the following configuration command script: Step 11 Respond to the following prompts. Select 2 to save the initial configuration: Using Cisco Configuration Professional Express Using the Cisco CLIManual Configuration Initial CLI Configuration Configuring the Router Hostname Configuring the Enable and Enable Secret Passwords Restrictions Configuring the Console Idle Privileged EXEC Timeout Page Configuring Gigabit Ethernet Interfaces Page Specifying a Default Route or Gateway of Last Resort Configuring IP Routing and IP Protocols IP Routing Default Routes Default Network Gateway of Last Resort 5-16 Command or Action Purpose Specifying a Default Route: Example Sample Output for the show ip route Command Step 4 ip route dest-prefix mask next-hop-ip-address Configuring Virtual Terminal Lines for Remote Console Access Example What to Do Next Configuring the Auxiliary Line Verifying Network Connectivity Prerequisites Page Saving Your Router Configuration Saving Backup Copies of Configuration and System Image Page Verifying the Initial Configuration Page Getting Software Licenses for the Router Activating a New Software Package or Feature RMA License Transfer Additional Information