Americas Headquarters
April
Cisco Systems, Inc 170 West Tasman Drive San Jose, CA
800 553-NETS Fax 408
Turn the television or radio antenna until the interference stops
Hardware Features
C O N T E N T S
Preface
Obtaining Documentation, Obtaining Support, and Security Guidelines
Diagnosing Problems
Using the Mode Button to Reset the Switch Module
Console Port
Verify Switch Module POST Results
Preface
Audience
Purpose
Conventions
Related Publications
Obtaining Documentation, Obtaining Support, and Security Guidelines
http//www-03.ibm.com/systems/bladecenter
viii
Switch Modules
Switch Modules, page Hardware Features, page Management Options, page
Switch Model
Product Overview
Hardware Features
Switch Model
Catalyst Switch Module 3110G, 3110X, and 3012 continued
Figure 1-1 Catalyst Switch Module 3110G and
10/100/1000 Ethernet Ports
Figure 1-2 Catalyst Switch Module
Chapter 1 Product Overview Hardware Features
OL-12192-01
10-Gigabit Ethernet Module Slot
Port Numbering
Internal 100BASE-T Ethernet Management Port
Port
Switch Module LEDs
Figure 1-3 Switch Module LEDs and Mode Button
Mode Button
System Power LED
Stack Master LED
Color
Fault/Stack Mode LED
Fault LED
Stack Mode Description
Fault Mode Description
Port LEDs
Activity LED Description
Link Status LED Description
LED Description
Management Options
StackWise Plus Ports
Console Port
Port Status LED Description
Network Configurations
1-10
Switch Module Installation
Preparing for Installation
Safety Warnings
Preparing for Installation, page Installing the Switch Module, page
Warning Class 1 laser product. Statement
Installation Guidelines
Box Contents
Installing the Switch Module
Figure 2-1 Blade Enclosure Rear-Panel View
After Installing the Switch Module
Creating Switch Stacks
Stacking Guidelines
Connecting a Switch Stack
Figure 2-3 Connecting the StackWise Plus Cables
Switch Stack Cabling Examples
Chapter 2 Switch Module Installation Creating Switch Stacks
OL-12192-01
203294
Chapter 2 Switch Module Installation Creating Switch Stacks
OL-12192-01
203295
2-10
Chapter 2 Switch Module Installation Creating Switch Stacks
OL-12192-01
203296
Installing Devices in the 10-Gigabit Ethernet Slot
Installing an X2 Transceiver Module
2-11
Removing a Module
2-12
Figure 2-7 Installing an X2 Transceiver Module
Connecting Devices to the Ethernet Ports
Where to Go Next
Device
Crossover Cable
2-14
Chapter 2 Switch Module Installation Where to Go Next
OL-12192-01
Troubleshooting
Diagnosing Problems
Verify Switch Module POST Results
Verify Switch Module LEDs
Verify Switch Module Connections
Bad or Damaged Cable
Ethernet and Fiber Cables
Link Status
Transceiver Issues
Port and Interface Settings
Ping End Device
Spanning Tree Loops
Resetting the Switch Module
Verify Switch Module Performance
Speed, Duplex, and Autonegotiation
Autonegotiation and Network Interface Cards
How to Replace a Failed Stack Member
Using the Mode Button to Reset the Switch Module
Chapter 3 Troubleshooting How to Replace a Failed Stack Member
OL-12192-01
Technical Specifications
Physical Specifications
Power Specifications
A P P E N D I X A
Appendix A Technical Specifications
OL-12192-01
Connector and Cable Specifications
Connector Specifications
“Connector Specifications” section on page B-1
“Cable and Adapter Specifications” section on page B-2
Cable and Adapter Specifications
10-Gigabit Ethernet Module Interface
Four Twisted-Pair Cable Pinouts, page B-4
Two Twisted-Pair Cable Pinouts, page B-5
10-Gigabit Ethernet X2 Transceiver Module Cable Specifications
Transmit Power
Receive Power
Modal
Four Twisted-Pair Cable Pinouts
Switch 1 TPO+ 2 TPO 3 TP1+ 6 TP1 4 TP2+ 5 TP2 7 TP3+ 8 TP3
Four Twisted-Pair Straight-Through Cable Schematic
Figure B-5 Four Twisted-Pair Crossover Cable Schematic
Two Twisted-Pair Cable Pinouts
Identifying a Crossover Cable
Appendix B Connector and Cable Specifications
Cable and Adapter Specifications
OL-12192-01
Numerics
I N D E
IN-1
IN-2
fault
fault/stack mode
system power
IN-3
IN-4
Index
OL-12192-01
