800 553-NETS Fax 408
Americas Headquarters
April
Cisco Systems, Inc 170 West Tasman Drive San Jose, CA
Turn the television or radio antenna until the interference stops
Obtaining Documentation, Obtaining Support, and Security Guidelines
Hardware Features
C O N T E N T S
Preface
Verify Switch Module POST Results
Diagnosing Problems
Using the Mode Button to Reset the Switch Module
Console Port
Conventions
Preface
Audience
Purpose
viii
Related Publications
Obtaining Documentation, Obtaining Support, and Security Guidelines
http//www-03.ibm.com/systems/bladecenter
Product Overview
Switch Modules
Switch Modules, page Hardware Features, page Management Options, page
Switch Model
Figure 1-1 Catalyst Switch Module 3110G and
Hardware Features
Switch Model
Catalyst Switch Module 3110G, 3110X, and 3012 continued
OL-12192-01
10/100/1000 Ethernet Ports
Figure 1-2 Catalyst Switch Module
Chapter 1 Product Overview Hardware Features
Port
10-Gigabit Ethernet Module Slot
Port Numbering
Internal 100BASE-T Ethernet Management Port
Figure 1-3 Switch Module LEDs and Mode Button
Switch Module LEDs
Color
Mode Button
System Power LED
Stack Master LED
Fault Mode Description
Fault/Stack Mode LED
Fault LED
Stack Mode Description
LED Description
Port LEDs
Activity LED Description
Link Status LED Description
Port Status LED Description
Management Options
StackWise Plus Ports
Console Port
1-10
Network Configurations
Preparing for Installation, page Installing the Switch Module, page
Switch Module Installation
Preparing for Installation
Safety Warnings
Warning Class 1 laser product. Statement
Box Contents
Installation Guidelines
Figure 2-1 Blade Enclosure Rear-Panel View
Installing the Switch Module
After Installing the Switch Module
Stacking Guidelines
Creating Switch Stacks
Figure 2-3 Connecting the StackWise Plus Cables
Connecting a Switch Stack
203294
Switch Stack Cabling Examples
Chapter 2 Switch Module Installation Creating Switch Stacks
OL-12192-01
OL-12192-01
Chapter 2 Switch Module Installation Creating Switch Stacks
203295
203296
2-10
Chapter 2 Switch Module Installation Creating Switch Stacks
OL-12192-01
Installing an X2 Transceiver Module
Installing Devices in the 10-Gigabit Ethernet Slot
2-11
2-12
Removing a Module
Figure 2-7 Installing an X2 Transceiver Module
Crossover Cable
Connecting Devices to the Ethernet Ports
Where to Go Next
Device
Chapter 2 Switch Module Installation Where to Go Next
2-14
OL-12192-01
Verify Switch Module LEDs
Troubleshooting
Diagnosing Problems
Verify Switch Module POST Results
Link Status
Verify Switch Module Connections
Bad or Damaged Cable
Ethernet and Fiber Cables
Spanning Tree Loops
Transceiver Issues
Port and Interface Settings
Ping End Device
Autonegotiation and Network Interface Cards
Resetting the Switch Module
Verify Switch Module Performance
Speed, Duplex, and Autonegotiation
Using the Mode Button to Reset the Switch Module
How to Replace a Failed Stack Member
OL-12192-01
Chapter 3 Troubleshooting How to Replace a Failed Stack Member
A P P E N D I X A
Technical Specifications
Physical Specifications
Power Specifications
OL-12192-01
Appendix A Technical Specifications
“Cable and Adapter Specifications” section on page B-2
Connector and Cable Specifications
Connector Specifications
“Connector Specifications” section on page B-1
Two Twisted-Pair Cable Pinouts, page B-5
Cable and Adapter Specifications
10-Gigabit Ethernet Module Interface
Four Twisted-Pair Cable Pinouts, page B-4
Modal
10-Gigabit Ethernet X2 Transceiver Module Cable Specifications
Transmit Power
Receive Power
Figure B-5 Four Twisted-Pair Crossover Cable Schematic
Four Twisted-Pair Cable Pinouts
Switch 1 TPO+ 2 TPO 3 TP1+ 6 TP1 4 TP2+ 5 TP2 7 TP3+ 8 TP3
Four Twisted-Pair Straight-Through Cable Schematic
Identifying a Crossover Cable
Two Twisted-Pair Cable Pinouts
Cable and Adapter Specifications
Appendix B Connector and Cable Specifications
OL-12192-01
I N D E
Numerics
IN-1
system power
IN-2
fault
fault/stack mode
IN-3
Index
IN-4
OL-12192-01