Cisco Systems, Inc 170 West Tasman Drive San Jose, CA
Americas Headquarters
April
800 553-NETS Fax 408
Turn the television or radio antenna until the interference stops
Preface
Hardware Features
C O N T E N T S
Obtaining Documentation, Obtaining Support, and Security Guidelines
Console Port
Diagnosing Problems
Using the Mode Button to Reset the Switch Module
Verify Switch Module POST Results
Purpose
Preface
Audience
Conventions
http//www-03.ibm.com/systems/bladecenter
Related Publications
Obtaining Documentation, Obtaining Support, and Security Guidelines
viii
Switch Model
Switch Modules
Switch Modules, page Hardware Features, page Management Options, page
Product Overview
Catalyst Switch Module 3110G, 3110X, and 3012 continued
Hardware Features
Switch Model
Figure 1-1 Catalyst Switch Module 3110G and
Chapter 1 Product Overview Hardware Features
10/100/1000 Ethernet Ports
Figure 1-2 Catalyst Switch Module
OL-12192-01
Internal 100BASE-T Ethernet Management Port
10-Gigabit Ethernet Module Slot
Port Numbering
Port
Switch Module LEDs
Figure 1-3 Switch Module LEDs and Mode Button
Stack Master LED
Mode Button
System Power LED
Color
Stack Mode Description
Fault/Stack Mode LED
Fault LED
Fault Mode Description
Link Status LED Description
Port LEDs
Activity LED Description
LED Description
Console Port
Management Options
StackWise Plus Ports
Port Status LED Description
Network Configurations
1-10
Safety Warnings
Switch Module Installation
Preparing for Installation
Preparing for Installation, page Installing the Switch Module, page
Warning Class 1 laser product. Statement
Installation Guidelines
Box Contents
Installing the Switch Module
Figure 2-1 Blade Enclosure Rear-Panel View
After Installing the Switch Module
Creating Switch Stacks
Stacking Guidelines
Connecting a Switch Stack
Figure 2-3 Connecting the StackWise Plus Cables
OL-12192-01
Switch Stack Cabling Examples
Chapter 2 Switch Module Installation Creating Switch Stacks
203294
Chapter 2 Switch Module Installation Creating Switch Stacks
OL-12192-01
203295
OL-12192-01
2-10
Chapter 2 Switch Module Installation Creating Switch Stacks
203296
Installing Devices in the 10-Gigabit Ethernet Slot
Installing an X2 Transceiver Module
2-11
Removing a Module
2-12
Figure 2-7 Installing an X2 Transceiver Module
Device
Connecting Devices to the Ethernet Ports
Where to Go Next
Crossover Cable
2-14
Chapter 2 Switch Module Installation Where to Go Next
OL-12192-01
Verify Switch Module POST Results
Troubleshooting
Diagnosing Problems
Verify Switch Module LEDs
Ethernet and Fiber Cables
Verify Switch Module Connections
Bad or Damaged Cable
Link Status
Ping End Device
Transceiver Issues
Port and Interface Settings
Spanning Tree Loops
Speed, Duplex, and Autonegotiation
Resetting the Switch Module
Verify Switch Module Performance
Autonegotiation and Network Interface Cards
How to Replace a Failed Stack Member
Using the Mode Button to Reset the Switch Module
Chapter 3 Troubleshooting How to Replace a Failed Stack Member
OL-12192-01
Power Specifications
Technical Specifications
Physical Specifications
A P P E N D I X A
Appendix A Technical Specifications
OL-12192-01
“Connector Specifications” section on page B-1
Connector and Cable Specifications
Connector Specifications
“Cable and Adapter Specifications” section on page B-2
Four Twisted-Pair Cable Pinouts, page B-4
Cable and Adapter Specifications
10-Gigabit Ethernet Module Interface
Two Twisted-Pair Cable Pinouts, page B-5
Receive Power
10-Gigabit Ethernet X2 Transceiver Module Cable Specifications
Transmit Power
Modal
Four Twisted-Pair Straight-Through Cable Schematic
Four Twisted-Pair Cable Pinouts
Switch 1 TPO+ 2 TPO 3 TP1+ 6 TP1 4 TP2+ 5 TP2 7 TP3+ 8 TP3
Figure B-5 Four Twisted-Pair Crossover Cable Schematic
Two Twisted-Pair Cable Pinouts
Identifying a Crossover Cable
Appendix B Connector and Cable Specifications
Cable and Adapter Specifications
OL-12192-01
Numerics
I N D E
IN-1
fault/stack mode
IN-2
fault
system power
IN-3
IN-4
Index
OL-12192-01
