Manuals / Cisco Systems / Marine Equipment / SONAR

Cisco Systems 3110G, 3110X Cable and Adapter Specifications, Gigabit Ethernet Module Interface

Models: 3110X

1 48

Download 48 pages 475 b

Page 40

Image 40

Appendix B Connector and Cable Specifications

Cable and Adapter Specifications

10-Gigabit Ethernet Module Interface

The 10-Gigabit Ethernet optical modules use SC connectors or Infiniband 4x connectors, as shown in Figure B-2and Figure B-3.

Figure B-2 10-Gigabit Ethernet Optical Module SC Connector

H8707

TxRx

Figure B-3 10-Gigabit Ethernet Infiniband 4x Connector

Console Port

The console port uses a USB connector. The supplied USB-to-DB-9 adapter cable is used to connect the console port of the switch module to a PC.

Cable and Adapter Specifications

These sections describe the cables and adapters used with the switch module:

•10-Gigabit Ethernet X2 Transceiver Module Cable Specifications, page B-3

•Four Twisted-Pair Cable Pinouts, page B-4

•Two Twisted-Pair Cable Pinouts, page B-5

•Identifying a Crossover Cable, page B-5

Catalyst Switch Module 3110G, 3110X, and 3012 for IBM BladeCenter Hardware Installation Guide

	B-2	OL-12192-01

Page 40

Image 40

Cisco Systems 3110G, 3110X, 3012 manual Cable and Adapter Specifications, Gigabit Ethernet Module Interface, Console Port

Contents

Americas Headquarters AprilCisco Systems, Inc 170 West Tasman Drive San Jose, CA 800 553-NETS Fax 408Turn the television or radio antenna until the interference stops Hardware Features C O N T E N T SPreface Obtaining Documentation, Obtaining Support, and Security GuidelinesDiagnosing Problems Using the Mode Button to Reset the Switch ModuleConsole Port Verify Switch Module POST ResultsPreface AudiencePurpose ConventionsRelated Publications Obtaining Documentation, Obtaining Support, and Security Guidelineshttp//www-03.ibm.com/systems/bladecenter viiiSwitch Modules Switch Modules, page Hardware Features, page Management Options, pageSwitch Model Product OverviewHardware Features Switch ModelCatalyst Switch Module 3110G, 3110X, and 3012 continued Figure 1-1 Catalyst Switch Module 3110G and10/100/1000 Ethernet Ports Figure 1-2 Catalyst Switch ModuleChapter 1 Product Overview Hardware Features OL-12192-0110-Gigabit Ethernet Module Slot Port NumberingInternal 100BASE-T Ethernet Management Port PortSwitch Module LEDs Figure 1-3 Switch Module LEDs and Mode ButtonMode Button System Power LEDStack Master LED ColorFault/Stack Mode LED Fault LEDStack Mode Description Fault Mode DescriptionPort LEDs Activity LED DescriptionLink Status LED Description LED DescriptionManagement Options StackWise Plus PortsConsole Port Port Status LED DescriptionNetwork Configurations 1-10Switch Module Installation Preparing for InstallationSafety Warnings Preparing for Installation, page Installing the Switch Module, pageWarning Class 1 laser product. Statement Installation Guidelines Box ContentsInstalling the Switch Module Figure 2-1 Blade Enclosure Rear-Panel ViewAfter Installing the Switch Module Creating Switch Stacks Stacking GuidelinesConnecting a Switch Stack Figure 2-3 Connecting the StackWise Plus CablesSwitch Stack Cabling Examples Chapter 2 Switch Module Installation Creating Switch StacksOL-12192-01 203294OL-12192-01 Chapter 2 Switch Module Installation Creating Switch Stacks203295 2-10 Chapter 2 Switch Module Installation Creating Switch StacksOL-12192-01 203296Installing an X2 Transceiver Module Installing Devices in the 10-Gigabit Ethernet Slot2-11 2-12 Removing a ModuleFigure 2-7 Installing an X2 Transceiver Module Connecting Devices to the Ethernet Ports Where to Go NextDevice Crossover CableChapter 2 Switch Module Installation Where to Go Next 2-14OL-12192-01 Troubleshooting Diagnosing ProblemsVerify Switch Module POST Results Verify Switch Module LEDsVerify Switch Module Connections Bad or Damaged CableEthernet and Fiber Cables Link StatusTransceiver Issues Port and Interface SettingsPing End Device Spanning Tree LoopsResetting the Switch Module Verify Switch Module PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsHow to Replace a Failed Stack Member Using the Mode Button to Reset the Switch ModuleChapter 3 Troubleshooting How to Replace a Failed Stack Member OL-12192-01Technical Specifications Physical SpecificationsPower Specifications A P P E N D I X AAppendix A Technical Specifications OL-12192-01Connector and Cable Specifications Connector Specifications“Connector Specifications” section on page B-1 “Cable and Adapter Specifications” section on page B-2Cable and Adapter Specifications 10-Gigabit Ethernet Module InterfaceFour Twisted-Pair Cable Pinouts, page B-4 Two Twisted-Pair Cable Pinouts, page B-510-Gigabit Ethernet X2 Transceiver Module Cable Specifications Transmit PowerReceive Power ModalFour Twisted-Pair Cable Pinouts Switch 1 TPO+ 2 TPO 3 TP1+ 6 TP1 4 TP2+ 5 TP2 7 TP3+ 8 TP3Four Twisted-Pair Straight-Through Cable Schematic Figure B-5 Four Twisted-Pair Crossover Cable SchematicTwo Twisted-Pair Cable Pinouts Identifying a Crossover CableCable and Adapter Specifications Appendix B Connector and Cable SpecificationsOL-12192-01 I N D E NumericsIN-1 IN-2 faultfault/stack mode system powerIN-3 Index IN-4OL-12192-01