Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems CISCO1750 manual Connecting Power to the Router, viii

Models: CISCO1750

1 84

Download 84 pages 20.31 Kb

Page 34

Figure 3 Inserting a WIC or VIC in the Router

Connecting Power to the Router

Figure 3 Inserting a WIC or VIC in the Router

VIC 2FXS

USEIN

1

SLOT 1Cisco		1750
		1750
		SLOT 2
			VIC
		CONSOLE	2FXO
SLOT	0	CONSOLE
FDX
100
LINK
10/100 ETH
	ERNET
		AUX

Guides

IN USE
1	SEE							IN USE
THIS	SEE	MANUAL
THIS		MANUAL		BEFORE
	SLOT ACC			BEFORE		INSTALLATION
			EPTS
				ONLY
					VOICE		INTERFACE	0
							INTERFACE	CARDS
								CARDS
				PVDM OK

17477

SEE	MANUAL
	MANUAL	BEFORE
		BEFORE	INSTALLATION
			INSTALLATION

USEIN

0

SLOT 2 OK

+5,	+12, -
	12 VDC

Interface card

Connecting Power to the Router

Read the following warnings before connecting the power to the router.

Warning The power supply is designed to work with TN power systems.

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 15AU.S. (240VAC, 16A international) is used on the phase conductors (all current-carrying conductors).

Cisco 1750 Router Hardware Installation Guide

viii	78-6169-02

Image 34

Cisco Systems CISCO1750 Connecting Power to the Router, Warning The power supply is designed to work with TN power systems

Contents

Cisco Systems, Inc 170 West Tasman Drive San Jose, CA Cisco 1750 Router Hardware Installation GuideCorporate Headquarters 800 553-NETS 6387 Fax 408Turn the television or radio antenna until the interference stops Move the equipment farther away from the television or radioCisco 1750 Router Hardware Installation Guide Copyright 2005 Cisco Systems, Inc. All rights reservedPage Before Installing the Router Key FeaturesInstallation Connecting the Router to Your Local NetworkEthernet Network Cabling Guidelines B-ii TroubleshootingTroubleshooting WICs and VICs Console Cable and Adapters B-iii VIC Cables and Pinouts B-vInstalling a Packet Voice Data Module C-x Installing a Mini-Flash Module C-viInstalling a Dual In-Line Memory Module C-ix Locating Modules C-vContents Cisco 1750 Router Hardware Installation Guide viii78-6169-02 About This Guide Organization Audience and ScopeRelated Publications Conventions Notes, Cautions, and WarningsPage xiii ¡Atención! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentesboldface screen font Commandsboldface DescriptionUnpacking the Router Cisco 1750 Router OverviewKey Features Rear-Panel Ports and LEDs Front-Panel LEDs Router Memory Additional Required Equipment Figure 1 shows the Cisco 1750 routerKey Features Cisco interface cards Rear-Panel Ports and LEDs Rear-Panel ConnectorsLabel/Color Rear-Panel Connectors continuedRear Panel LEDs Figure 3 Front-Panel LEDs Front-Panel LEDsRear Panel LEDs continued Front-Panel LEDsSupported CardsColor LED MeaningSupported CardsColor LED MeaningRouter Memory Types of Memory1750# show version Amounts of Memoryof memory When You Use It Unpacking the RouterAdditional Required Equipment Equipmenttypes, refer to the Cisco WAN Interface Cards Hardware EquipmentInstallation Before Installing the RouterConnecting the Router to Your Local Network Follow these steps to connect the router to your local network INSTALLATION Figure 1 Connecting the Router to the Local NetworkEthernet hub or switch 10, 100, or 10/100 Mbps ONLY VOINSTALLATIONInstalling WICs and VICs Safety InformationFollow these steps to remove and insert a card in the router Step 3 Remove the metal plate that covers the card slot viii Connecting Power to the RouterWarning The power supply is designed to work with TN power systems Figure 3 Inserting a WIC or VIC in the RouterStep 4 Press the router power switch to on Verifying Your Installation Optional Installation StepsConnecting a PC Console port Figure 5 Connecting the Console Cable to the RouterLight blue console cableConnecting a Modem xiiiWall-Mounting Cisco 1750 Router Hardware Installation Guide Optional Installation Steps78-6169-02 Cisco 1750 Router Hardware Installation Guide Optional Installation Steps78-6169-02 Troubleshooting Contacting Cisco or Your ResellerRecovering a Lost Password Changing the Configuration RegisterConfiguration register is Step 6 Record the break setting Break enabled-bit 8 is set toBreak disabled default setting-bit 8 is set to Router show versionResetting the Router Resetting the Password Problem Solving Resetting the Configuration Register ValueNumber of Blinks OK LED DiagnosticsMeaning Use the show diag command to help determine problems with a card Troubleshooting WICs and VICsviii Possible Solutions SymptomThe Cisco WAN Interface Cards Hardware Installation Guide Troubleshooting the Power System Compliance and Safety Information for the Cisco 1600 andTroubleshooting ISDN Troubleshooting the Power SystemTroubleshooting ISDN SymptomPossible Solutions Check the FollowingUse the show controller bri0 Use the isdn switch-typeUse show isdn status Troubleshooting ISDN continuedProblem Solving Cisco 1750 Router Hardware Installation Guide 78-6169-02Technical Specifications Operating temperature Power consumptionOperating Specifications Storage temperatureCabling Specifications Ethernet CablesStraight-Through Ethernet Cable RJ-45-to-RJ-45 Pinouts Ethernet Network Cabling GuidelinesEthernet Cabling Guidelines Console Cable and Adapters Figure 1 Identifying a Rollover Cable Table 3 Console Cable and Adapter Pinouts continuedH10632 VIC Cables and Pinouts Description SignalSignal RJ-11 PinoutE-lead Signaling outputSignaling ground returnviii VIC Cables and Pinouts Cisco 1750 Router Hardware Installation Guide78-6169-02 Installing and Upgrading Memory and Data Modules Safety InformationCisco 1750 Router Hardware Installation Guide Safety Information78-6169-02 Opening the Chassis Rear panel Figure 1 Removing the Chassis ScrewsNumber 1 Phillips screwdriver Top of routerLocating Modules Figure 2 Cisco 1750 Motherboard-Module LocationsInstalling a Mini-Flash Module Removing a Mini-Flash Modulemini-Flash memory module release lever, as shown in Figure viii Figure 5 Installing a Mini-Flash Module45 degrees Installing a Dual In-Line Memory Module Installing a Packet Voice Data Module Closing the Chassis Figure 8 Closing the Chassis INSTALLATIONINSTALLATION 22311I N D E Page Page Page