Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems CISCO1750 manual Conventions, Notes, Cautions, and Warnings

Models: CISCO1750

1 84

Download 84 pages 20.31 Kb

Page 11

Conventions

About This Guide

Conventions

•Cisco 1700 Router Software Configuration Guide describes some common network scenarios and how to use the Cisco IOS command-line interface (CLI) to configure the router in these scenarios.

•Cisco 1750 Router Voice-over-IP Configuration Guide provides instructions on how to use Cisco IOS software to configure voice interfaces.

•Cisco WAN Interface Cards Hardware Installation Guide describes how to install and configure the WICs and VICs that are supported by the Cisco 1750 router.

•Cisco IOS command reference and configuration guides provide complete information about all Cisco IOS CLI commands and how to use them, as well as information on designing and configuring LANs and WANs.

Conventions

This guide uses the following conventions for instructions and information.

Notes, Cautions, and Warnings

Notes, cautions, and warnings use the following conventions and symbols:

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.

Caution This caution symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Cisco 1750 Router Hardware Installation Guide

	78-6169-02	xi

Image 11

Cisco Systems CISCO1750 manual Conventions, Notes, Cautions, and Warnings

Contents

800 553-NETS 6387 Fax 408 Cisco 1750 Router Hardware Installation GuideCorporate Headquarters Cisco Systems, Inc 170 West Tasman Drive San Jose, CAMove the equipment farther away from the television or radio Turn the television or radio antenna until the interference stopsCopyright 2005 Cisco Systems, Inc. All rights reserved Cisco 1750 Router Hardware Installation GuidePage Connecting the Router to Your Local Network Key FeaturesInstallation Before Installing the RouterConsole Cable and Adapters B-iii VIC Cables and Pinouts B-v TroubleshootingTroubleshooting WICs and VICs Ethernet Network Cabling Guidelines B-iiLocating Modules C-v Installing a Mini-Flash Module C-viInstalling a Dual In-Line Memory Module C-ix Installing a Packet Voice Data Module C-x78-6169-02 viiiContents Cisco 1750 Router Hardware Installation Guide About This Guide Related Publications Audience and ScopeOrganization Notes, Cautions, and Warnings ConventionsPage ¡Atención! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes xiiiDescription Commandsboldface boldface screen fontAdditional Required Equipment Figure 1 shows the Cisco 1750 router Cisco 1750 Router OverviewKey Features Rear-Panel Ports and LEDs Front-Panel LEDs Router Memory Unpacking the RouterKey Features Cisco interface cards Rear-Panel Connectors Rear-Panel Ports and LEDsRear Panel LEDs Rear-Panel Connectors continuedLabel/Color Front-Panel LEDs Front-Panel LEDsRear Panel LEDs continued Figure 3 Front-Panel LEDsLED Meaning CardsColor SupportedLED Meaning CardsColor SupportedTypes of Memory Router Memoryof memory Amounts of Memory1750# show version Equipment Unpacking the RouterAdditional Required Equipment When You Use ItEquipment types, refer to the Cisco WAN Interface Cards HardwareBefore Installing the Router InstallationConnecting the Router to Your Local Network Follow these steps to connect the router to your local network ONLY VOINSTALLATION Figure 1 Connecting the Router to the Local NetworkEthernet hub or switch 10, 100, or 10/100 Mbps INSTALLATIONSafety Information Installing WICs and VICsFollow these steps to remove and insert a card in the router Step 3 Remove the metal plate that covers the card slot Figure 3 Inserting a WIC or VIC in the Router Connecting Power to the RouterWarning The power supply is designed to work with TN power systems viiiStep 4 Press the router power switch to on Optional Installation Steps Verifying Your InstallationConnecting a PC console cable Figure 5 Connecting the Console Cable to the RouterLight blue Console portxiii Connecting a ModemWall-Mounting 78-6169-02 Optional Installation StepsCisco 1750 Router Hardware Installation Guide 78-6169-02 Optional Installation StepsCisco 1750 Router Hardware Installation Guide Contacting Cisco or Your Reseller TroubleshootingChanging the Configuration Register Recovering a Lost PasswordRouter show version Step 6 Record the break setting Break enabled-bit 8 is set toBreak disabled default setting-bit 8 is set to Configuration register isResetting the Router Resetting the Password Resetting the Configuration Register Value Problem SolvingMeaning OK LED DiagnosticsNumber of Blinks viii Troubleshooting WICs and VICsUse the show diag command to help determine problems with a card The Cisco WAN Interface Cards Hardware Installation Guide SymptomPossible Solutions Compliance and Safety Information for the Cisco 1600 and Troubleshooting the Power SystemTroubleshooting the Power System Troubleshooting ISDNCheck the Following SymptomPossible Solutions Troubleshooting ISDNTroubleshooting ISDN continued Use the isdn switch-typeUse show isdn status Use the show controller bri078-6169-02 Problem Solving Cisco 1750 Router Hardware Installation GuideTechnical Specifications Storage temperature Power consumptionOperating Specifications Operating temperatureEthernet Cables Cabling SpecificationsEthernet Cabling Guidelines Ethernet Network Cabling GuidelinesStraight-Through Ethernet Cable RJ-45-to-RJ-45 Pinouts Console Cable and Adapters H10632 Table 3 Console Cable and Adapter Pinouts continuedFigure 1 Identifying a Rollover Cable VIC Cables and Pinouts RJ-11 Pinout SignalSignal Descriptionreturn Signaling outputSignaling ground E-lead78-6169-02 VIC Cables and Pinouts Cisco 1750 Router Hardware Installation Guideviii Safety Information Installing and Upgrading Memory and Data Modules78-6169-02 Safety InformationCisco 1750 Router Hardware Installation Guide Opening the Chassis Top of router Figure 1 Removing the Chassis ScrewsNumber 1 Phillips screwdriver Rear panelFigure 2 Cisco 1750 Motherboard-Module Locations Locating ModulesRemoving a Mini-Flash Module Installing a Mini-Flash Modulemini-Flash memory module release lever, as shown in Figure 45 degrees Figure 5 Installing a Mini-Flash Moduleviii Installing a Dual In-Line Memory Module Installing a Packet Voice Data Module Closing the Chassis 22311 INSTALLATIONINSTALLATION Figure 8 Closing the ChassisI N D E Page Page Page