Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems CISCO1750 manual Verifying Your Installation, Optional Installation Steps

Models: CISCO1750

1 84

Download 84 pages 20.31 Kb

Page 36

Verifying Your Installation

Verifying Your Installation

Verifying Your Installation

You can verify that you have correctly installed the router by checking the following LEDs:

•PWR (front panel)—On when power is being supplied to the router.

•OK (front panel)—On when the router software is loaded and functional. Blinking means that the router is performing a power-on self-test (POST).

•ETH ACT (front panel)—Blinking when there is network traffic on the local Ethernet LAN.

•SLOTØ, SLOT1, and SLOT2 (front panel)—Activity on PORTØ and PORT1 of each of these slots varies, depending on the type of WIC or VIC installed. Refer to Table 4 in the “Cisco 1750 Router Overview” chapter for detailed information on activity at different ports.

•SLOT 0 and SLOT 1 OK (rear panel)—On when a WIC or VIC is correctly installed in the slot.

•SLOT 2 OK (rear panel)—On when a VIC is correctly installed in the slot.

•LINK (rear panel)—On when the router is correctly connected to the local Ethernet LAN through the 10/100-Mbps Ethernet port.

Optional Installation Steps

This section describes the following installation steps that you might or might not use, depending on your site and how you are configuring the router:

•Connecting a PC

•Connecting a Modem

•Wall-Mounting

Cisco 1750 Router Hardware Installation Guide

x	78-6169-02

Image 36

Cisco Systems CISCO1750 manual Verifying Your Installation, Optional Installation Steps

Contents

Cisco 1750 Router Hardware Installation Guide Corporate HeadquartersCisco Systems, Inc 170 West Tasman Drive San Jose, CA 800 553-NETS 6387 Fax 408Turn the television or radio antenna until the interference stops Move the equipment farther away from the television or radioCisco 1750 Router Hardware Installation Guide Copyright 2005 Cisco Systems, Inc. All rights reservedPage Key Features InstallationBefore Installing the Router Connecting the Router to Your Local NetworkTroubleshooting Troubleshooting WICs and VICsEthernet Network Cabling Guidelines B-ii Console Cable and Adapters B-iii VIC Cables and Pinouts B-vInstalling a Mini-Flash Module C-vi Installing a Dual In-Line Memory Module C-ixInstalling a Packet Voice Data Module C-x Locating Modules C-vviii Contents Cisco 1750 Router Hardware Installation Guide78-6169-02 About This Guide Audience and Scope OrganizationRelated Publications Conventions Notes, Cautions, and WarningsPage xiii ¡Atención! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentesCommands boldfaceboldface screen font DescriptionCisco 1750 Router Overview Key Features Rear-Panel Ports and LEDs Front-Panel LEDs Router MemoryUnpacking the Router Additional Required Equipment Figure 1 shows the Cisco 1750 routerKey Features Cisco interface cards Rear-Panel Ports and LEDs Rear-Panel ConnectorsRear-Panel Connectors continued Label/ColorRear Panel LEDs Front-Panel LEDs Rear Panel LEDs continuedFigure 3 Front-Panel LEDs Front-Panel LEDsCards ColorSupported LED MeaningCards ColorSupported LED MeaningRouter Memory Types of MemoryAmounts of Memory 1750# show versionof memory Unpacking the Router Additional Required EquipmentWhen You Use It Equipmenttypes, refer to the Cisco WAN Interface Cards Hardware EquipmentInstallation Before Installing the RouterConnecting the Router to Your Local Network Follow these steps to connect the router to your local network Figure 1 Connecting the Router to the Local Network Ethernet hub or switch 10, 100, or 10/100 MbpsINSTALLATION ONLY VOINSTALLATIONInstalling WICs and VICs Safety InformationFollow these steps to remove and insert a card in the router Step 3 Remove the metal plate that covers the card slot Connecting Power to the Router Warning The power supply is designed to work with TN power systemsviii Figure 3 Inserting a WIC or VIC in the RouterStep 4 Press the router power switch to on Verifying Your Installation Optional Installation StepsConnecting a PC Figure 5 Connecting the Console Cable to the Router Light blueConsole port console cableConnecting a Modem xiiiWall-Mounting Optional Installation Steps Cisco 1750 Router Hardware Installation Guide78-6169-02 Optional Installation Steps Cisco 1750 Router Hardware Installation Guide78-6169-02 Troubleshooting Contacting Cisco or Your ResellerRecovering a Lost Password Changing the Configuration RegisterStep 6 Record the break setting Break enabled-bit 8 is set to Break disabled default setting-bit 8 is set toConfiguration register is Router show versionResetting the Router Resetting the Password Problem Solving Resetting the Configuration Register ValueOK LED Diagnostics Number of BlinksMeaning Troubleshooting WICs and VICs Use the show diag command to help determine problems with a cardviii Symptom Possible SolutionsThe Cisco WAN Interface Cards Hardware Installation Guide Troubleshooting the Power System Compliance and Safety Information for the Cisco 1600 andTroubleshooting ISDN Troubleshooting the Power SystemSymptom Possible SolutionsTroubleshooting ISDN Check the FollowingUse the isdn switch-type Use show isdn statusUse the show controller bri0 Troubleshooting ISDN continuedProblem Solving Cisco 1750 Router Hardware Installation Guide 78-6169-02Technical Specifications Power consumption Operating SpecificationsOperating temperature Storage temperatureCabling Specifications Ethernet CablesEthernet Network Cabling Guidelines Straight-Through Ethernet Cable RJ-45-to-RJ-45 PinoutsEthernet Cabling Guidelines Console Cable and Adapters Table 3 Console Cable and Adapter Pinouts continued Figure 1 Identifying a Rollover CableH10632 VIC Cables and Pinouts Signal SignalDescription RJ-11 PinoutSignaling output Signaling groundE-lead returnVIC Cables and Pinouts Cisco 1750 Router Hardware Installation Guide viii78-6169-02 Installing and Upgrading Memory and Data Modules Safety InformationSafety Information Cisco 1750 Router Hardware Installation Guide78-6169-02 Opening the Chassis Figure 1 Removing the Chassis Screws Number 1 Phillips screwdriverRear panel Top of routerLocating Modules Figure 2 Cisco 1750 Motherboard-Module LocationsInstalling a Mini-Flash Module Removing a Mini-Flash Modulemini-Flash memory module release lever, as shown in Figure Figure 5 Installing a Mini-Flash Module viii45 degrees Installing a Dual In-Line Memory Module Installing a Packet Voice Data Module Closing the Chassis INSTALLATION INSTALLATIONFigure 8 Closing the Chassis 22311I N D E Page Page Page