Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems IPS4510K9, IPS4520K9 specifications Removal screws

Models: IPS4510K9

1 36

Download 36 pages 45.7 Kb

Page 4

Removal screws

Chapter 7 Installing the IPS 4510 and IPS 4520

Chassis Features

Figure 7-2shows the front view of the IPS 4510 and IPS 4520.

Figure 7-2 IPS 4510 and IPS 4520 Front Panel Features

					SFP/SFP+	5	4	3	2	1	0
1	3	4	5	6	2				7

									Cisco IPS 4520
								Cisco ASA 5585-X IPS SSP		331672
1	MGMT	0	USB	PWR BOOT ALARM ACT VPN PS1	PS0	HDD1	HDD0			331672
			0
			1						RESET
									RESET
8		9	10 11	12				13 14	15	1

1	Removal screws	2	Reserved bays for hard disk drives1
3	TenGigabitEthernet 0/9	4	TenGigabitEthernet 0/8
	(1-Gb and 10-Gb fiber SFP/SFP+ modules)		(1-Gb and 10-Gb fiber SFP/SFP+ modules)

5	TenGigabitEthernet 0/7	6	TenGigabitEthernet 0/6
	(1-Gb and 10-Gb fiber SFP/SFP+ modules)		(1-Gb and 10-Gb fiber SFP/SFP+ modules)

7	GigabitEthernet 0/0 through 0/5	8	Management 0/12
	(from right to left, 1-Gb copper RJ45)		(GigabitEthernet RJ45)

9	Management 0/0	10	USB port
	(GigabitEthernet RJ45)

11	USB port	12	Front panel indicators

13	Auxiliary port (RJ45)	14	Console port (RJ45)

15	Reset3

1.Hard disk drives are not supported at this time. The hard disk drive bays are empty.

2.Reserved for future use.

3.Reserved for future use.

Cisco Intrusion Prevention System Appliance and Module Installation Guide for IPS 7.1

7-4	OL-24002-01

Image 4

Cisco Systems IPS4510K9, IPS4520K9 specifications Removal screws

Contents

Contents Installation Notes and CaveatsInstalling the IPS 4510 and IPS C H A P T E RProduct Overview Chassis Features Removal screws Indicator DescriptionDescription Indicatorthe back panel Figure 7-4 shows the back panel features Indicator IndicatorDescription IN OKSpecifications Dimensions and WeightPower IndicatorEnvironment Accessories7-10 Memory Configurations Power Supply Module RequirementsSupported SFP/SFP+ Modules ModelInstalling the IPS 4510 and IPS 1G SFP Module10G SFP+ Module 7-127-13 a.Install the SFP/SFP+ module7-14 Step 5 Install the electrical cablesFor More Information Removing and Installing the Core IPS SSP7-15 7-16 ModuleRemoving and Installing the Power Supply Module 7-177-18 Power supply module and power supply module handleRemoving and Installing the Fan Module 7-19Installing the Slide Rail Kit Hardware 7-20Installing and Removing the Slide Rail Kit 7-21Package Contents, page Installing the Chassis in the Rack, pageInstalling the Chassis in the Rack Package Contents7-22 7-23 Figure 7-9Square Studs for Square Hole Post7-24 Step 2 Secure the slide rail to the rack post with the provided #10-32screws by tightening the screws at the front and rear end of the slide rail to the rack post Figure 7-10.Both front and rear rack posts must be secured with the screws before you install the chassis7-25 Figure 7-11Installing the #10-32Cage Nuts7-26 Step 4 Install the chassis on the outer rail. Make sure that the U-barsare aligned to the outer rail evenly, then push the chassis into the rack Figure7-27 Figure 7-13Securing the Chassis to the Outer RailRemoving the Chassis from the Rack 7-287-29 Chapter 7 Installing the IPS 4510 and IPSInstalling and Removing the Slide Rail Kit Figure 7-15Pressing Down the Release Hook7-30 Power off the sensor7-31 Bracket7-32 Step 12 Reattach the power cable to the sensorInstalling the Cable Management Brackets 7-33Troubleshooting Loose Connections 7-34IPS 4500 Series Sensors and the SwitchApp 7-35Chapter 7 Installing the IPS 4510 and IPS IPS 4500 Series Sensors and the SwitchApp7-36 Chapter 7 Installing the IPS 4510 and IPSIPS 4500 Series Sensors and the SwitchApp OL-24002-01