Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems IPS4510K9, IPS4520K9 specifications Troubleshooting Loose Connections, 7-34

Models: IPS4510K9

1 36

Download 36 pages 45.7 Kb

Page 34

Troubleshooting Loose Connections

Chapter 7 Installing the IPS 4510 and IPS 4520

Troubleshooting Loose Connections

Figure 7-18 Cable Management Brackets for the Slide Rail

333053

Step 4 Tighten the screws in to the rack.

Step 5 Reattach the power cable to the sensor.

Step 6 Organize the cables through the cable management brackets on the sensor.

Step 7 Power on the sensor.

Troubleshooting Loose Connections

Perform the following actions to troubleshoot loose connections on sensors:

•Make sure all power cords are securely connected.

•Make sure all cables are properly aligned and securely connected for all external and internal components.

•Remove and check all data and power cables for damage. Make sure no cables have bent pins or damaged connectors.

•Make sure each device is properly seated.

•If a device has latches, make sure they are completely closed and locked.

•Check any interlock or interconnect indicators that indicate a component is not connected properly.

•If problems continue, remove and reinstall each device, checking the connectors and sockets for bent pins or other damage.

	Cisco Intrusion Prevention System Appliance and Module Installation Guide for IPS 7.1
7-34	OL-24002-01

Image 34

Cisco Systems IPS4510K9, IPS4520K9 specifications Troubleshooting Loose Connections, 7-34

Contents

Installing the IPS 4510 and IPS ContentsInstallation Notes and Caveats C H A P T E RProduct Overview Chassis Features Removal screws Indicator DescriptionDescription Indicatorthe back panel Figure 7-4 shows the back panel features Description IndicatorIndicator IN OKPower SpecificationsDimensions and Weight IndicatorEnvironment Accessories7-10 Supported SFP/SFP+ Modules Memory ConfigurationsPower Supply Module Requirements Model10G SFP+ Module Installing the IPS 4510 and IPS1G SFP Module 7-127-13 a.Install the SFP/SFP+ module7-14 Step 5 Install the electrical cablesFor More Information Removing and Installing the Core IPS SSP7-15 7-16 ModuleRemoving and Installing the Power Supply Module 7-177-18 Power supply module and power supply module handleRemoving and Installing the Fan Module 7-19Installing the Slide Rail Kit Hardware 7-20Package Contents, page Installing and Removing the Slide Rail Kit7-21 Installing the Chassis in the Rack, pageInstalling the Chassis in the Rack Package Contents7-22 7-23 Figure 7-9Square Studs for Square Hole Post7-24 Step 2 Secure the slide rail to the rack post with the provided #10-32screws by tightening the screws at the front and rear end of the slide rail to the rack post Figure 7-10.Both front and rear rack posts must be secured with the screws before you install the chassis7-25 Figure 7-11Installing the #10-32Cage Nuts7-26 Step 4 Install the chassis on the outer rail. Make sure that the U-barsare aligned to the outer rail evenly, then push the chassis into the rack Figure7-27 Figure 7-13Securing the Chassis to the Outer RailRemoving the Chassis from the Rack 7-28Installing and Removing the Slide Rail Kit 7-29Chapter 7 Installing the IPS 4510 and IPS Figure 7-15Pressing Down the Release Hook7-30 Power off the sensor7-31 Bracket7-32 Step 12 Reattach the power cable to the sensorInstalling the Cable Management Brackets 7-33Troubleshooting Loose Connections 7-34Chapter 7 Installing the IPS 4510 and IPS IPS 4500 Series Sensors and the SwitchApp7-35 IPS 4500 Series Sensors and the SwitchAppIPS 4500 Series Sensors and the SwitchApp 7-36Chapter 7 Installing the IPS 4510 and IPS OL-24002-01