Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems IPS4510K9, IPS4520K9 specifications Installing the Slide Rail Kit Hardware, 7-20

Models: IPS4510K9

1 36

Download 36 pages 45.7 Kb

Page 20

Installing the Slide Rail Kit Hardware

Chapter 7 Installing the IPS 4510 and IPS 4520

Installing the Slide Rail Kit Hardware

Step 3 Install the new fan module by aligning it with the fan module bay and pushing it into place until it is seated.

2

Cisco ASA 1200W AC

Cisco--

ASA--

FAN

3

1

2

1 Fan module and fan handle

2 Fan module screw

3Power supply module

Step 4 Tighten the captive screws.

Step 5 Verify that the fan indicator on the lower right-hand of the back panel is green.

253910

Installing the Slide Rail Kit Hardware

Before installing the appliance in the slide rail kit, you must install the slide rail kit hardware. To install the slide rail kit hardware on the IPS 4510 and IPS 4520, follow these steps:

Step 1 Power off the appliance.

Step 2 Remove the power cable from the appliance.

Step 3 If your appliance has the fixed cable management brackets, do the following:

a.Remove the cable management brackets from the front sides of the appliance.

b.Remove the appliance from the rack.

c.Remove the front brackets, left and right side brackets, and left and right rear brackets from the appliance.

	Cisco Intrusion Prevention System Appliance and Module Installation Guide for IPS 7.1
7-20	OL-24002-01

Image 20

Cisco Systems IPS4510K9, IPS4520K9 specifications Installing the Slide Rail Kit Hardware, 7-20

Contents

Contents Installation Notes and CaveatsInstalling the IPS 4510 and IPS C H A P T E RProduct Overview Chassis Features Removal screws Indicator Descriptionthe back panel IndicatorDescription Figure 7-4 shows the back panel features Indicator IndicatorDescription IN OKSpecifications Dimensions and WeightPower Indicator7-10 AccessoriesEnvironment Memory Configurations Power Supply Module RequirementsSupported SFP/SFP+ Modules ModelInstalling the IPS 4510 and IPS 1G SFP Module10G SFP+ Module 7-127-13 a.Install the SFP/SFP+ module7-14 Step 5 Install the electrical cables7-15 Removing and Installing the Core IPS SSPFor More Information 7-16 ModuleRemoving and Installing the Power Supply Module 7-177-18 Power supply module and power supply module handleRemoving and Installing the Fan Module 7-19Installing the Slide Rail Kit Hardware 7-20Installing and Removing the Slide Rail Kit 7-21Package Contents, page Installing the Chassis in the Rack, page7-22 Package ContentsInstalling the Chassis in the Rack 7-23 Figure 7-9Square Studs for Square Hole Post7-24 Step 2 Secure the slide rail to the rack post with the provided #10-32screws by tightening the screws at the front and rear end of the slide rail to the rack post Figure 7-10.Both front and rear rack posts must be secured with the screws before you install the chassis7-25 Figure 7-11Installing the #10-32Cage Nuts7-26 Step 4 Install the chassis on the outer rail. Make sure that the U-barsare aligned to the outer rail evenly, then push the chassis into the rack Figure7-27 Figure 7-13Securing the Chassis to the Outer RailRemoving the Chassis from the Rack 7-287-29 Chapter 7 Installing the IPS 4510 and IPSInstalling and Removing the Slide Rail Kit Figure 7-15Pressing Down the Release Hook7-30 Power off the sensor7-31 Bracket7-32 Step 12 Reattach the power cable to the sensorInstalling the Cable Management Brackets 7-33Troubleshooting Loose Connections 7-34IPS 4500 Series Sensors and the SwitchApp 7-35Chapter 7 Installing the IPS 4510 and IPS IPS 4500 Series Sensors and the SwitchApp7-36 Chapter 7 Installing the IPS 4510 and IPSIPS 4500 Series Sensors and the SwitchApp OL-24002-01