Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems OL-23421-02 manual 1-10, flash1, flash or, flash0

Models: OL-23421-02

1 46

Download 46 pages 8.57 Kb

Page 16

flash1:

Chapter 1 Product Overview

Router Compact Flash Memory Cards

For more information on the Swap Drive feature, see: http://www.cisco.com/en/US/docs/routers/connectedgrid/cgr2010/software/15_2_2_t/cgr2010_15_2_2 _t_swcg.html#wp2039791

The router supports a maximum of two compact flash memory cards. The router ships with one compact flash card installed in Slot CF0 and supports a second, optional flash card that you can order with the router or supply separately.

Figure 5 illustrates the location of the compact flash card slots on the router.

Figure 5

Cisco Connected Grid 2010 Router—Compact Flash Memory Card Slot Locations

CF1 CF0

PSU OK	PWR-150W-HV

PSU1

CAUTION: This unit may have more than one power source. Disconnect all power sources before servicing to avoid electric shock.

	SFP	SFP	GE	GE	SLOT
	0/1	0/0	0/1	0/0			USB	PSU
ACT	EN	EN	LINK	LINK	3	1	CON	2
SYS	SPD	SPD	SPD	SPD	2	0	CONSOLE	1

PSU OK	PWR-150W-HV
	PSU2
CF1	CF0

DO NOT REMOVE DURING

NETWORK OPERATION

PS Type	Input Rating Per Sources
LoV dc	24-60V	10A
HiV dc	100-270V	2A
V ac, 50/60 Hz	100-240V ~	2A

DO NOT REMOVE DURING

NETWORK OPERATION

Cisco Connected Grid Router 2000 Series

284213

		1	2

	Label on			Cisco IOS
Item	Router	Description		Interface Name

1	CF1	This slot supports an optional compact flash card that you can		flash1:
		order with the router or supply separately. The Connected Grid
		Swap Drive feature is not supported on this slot.

2	CF0	This is the required slot for use with the Connected Grid Swap		flash or
		Drive feature. The router comes with a compact flash card		flash0:
		already installed in this slot.
		The Connected Grid Swap Drive feature is supported on this
		CF slot only.

For additional information about the router compact flash memory support, refer to the router hardware installation guide at:

http://www.cisco.com/en/US/products/ps10977/prod_installation_guides_list.html

	Cisco Connected Grid Ethernet Switch Module Interface Card Getting Started Guide
1-10	OL-23421-02

Image 16

Cisco Systems OL-23421-02 manual 1-10, flash1, flash or, flash0

Contents

Cisco Systems, Inc Cisco Connected Grid Ethernet SwitchModule Interface Card Getting Started Guide Text Part Number OL-23421-02No combinations are authorized or intended under this document 2012-2014 Cisco Systems, Inc. All rights reservedObtaining Documentation and Submitting a Service Request InstallationPre-Installation Switch ModelsCisco Configuration Professional Resetting the Switch ModuleManaging the Switch Module SFP Module ConnectorsPurpose PrefaceDocument Conventions Related Publications Obtaining Documentation and Submitting a Service RequestSwitch Models Switch Models, page Ports, page LEDs, pageProduct Overview C H A P T E RPorts Port LocationsPort Locations, page Port Labeling, page 10/100BASE-T Ports, page PoE and PoE+ Ports, page 10/100 Mb/s SFP Module Slots, pagePort Port LabelingLabel PoE and PoE+ Ports 10/100BASE-T PortsGRWIC-D-ES-2S-8PC Port Labeling 100/1000 Mb/s SFP Module Slots 10/100 Mb/s SFP Module SlotsDual-Purpose Gigabit Ethernet Ports Type of SFP Module Supported SFPsModel LEDs Description GRWIC-D-ES-2S-8PC Switch Module Copper Model LEDsDescription Router Compact Flash Memory Cards 1-10 flash1flash or flash0Installation Pre-InstallationInstallation Warning Statements Pre-Installation Installation Connecting to the NetworkInstallation Figure 2-2 Positioning the Switch Module to Install in the Router Chapter 2 Installation InstallationFigure 2-1 Removing the Slot Divider From the CGR 2010 Router OL-23421-02Step 5 Tighten the screws Connecting to the Network Connecting the Copper Switch ModuleConnecting the Copper Switch Module, page Connecting the Fiber Switch Module, pageConnecting the Fiber Switch Module Figure 2-5 Connecting the Copper Model to the NetworkRemoving the Switch Module Chapter 2 Installation Removing the Switch Module OL-23421-02Express Setup Express SetupSystem Requirements Express Setup Troubleshooting Express Setup Resetting the Switch ModuleStep 2 Verify that no device is connected to the switch module Step 6 Select one of the following Step 3 Enter the Network Settings values Troubleshooting Express Setup Resetting the Switch ModuleProblem ResolutionChapter 3 Express Setup Resetting the Switch Module Step 3 Follow the steps in Express Setup, pageOL-23421-02 Managing the Switch Module Using the Device ManagerCisco Configuration Professional Using the Device Manager Cisco Configuration ProfessionalAccessing the Switch Module Other Management OptionsInterface IP AddressDisconnecting from the Switch Module Connecting Devices to the Switch Module Dual-Purpose Port with RJ-45 and SFP Connectors, page10/100BASE-T Ports, page SFP Module Slots, page Dual-Purpose Port with RJ-45 and SFP Connectors, pageSFP Module Slots 237940237941 237942Figure 4-3 Connecting the Cable into the SFP Port Chapter 4 Managing the Switch ModuleDual-Purpose Port with RJ-45 and SFP Connectors 237964 Figure 4-4 Ethernet Cable Connected to the RJ-45 ConnectorFigure 4-5 Dual-Purpose Connectors Verifying Port Connectivity237965 4-10 Chapter 4 Managing the Switch ModuleConnecting Devices to the Switch Module OL-23421-02Cable and Connectors Connector SpecificationsSFP Module Connectors Connector Specifications, page A-1 Cables and Adapters, page A-2Cables and Adapters Dual-Purpose PortsSFP Module Cables SFP Module Cables, page A-2 Cable Pinouts, page A-4Size/Cladding Cable Pinouts Four Twisted-Pair Crossover Cable Schematics for 1000BASE-T Ports Figure A-6Figure A-7 Figure A-8 Identifying a Crossover CableAppendix A Cable and Connectors Cables and Adapters OL-23421-02