Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems OL-23421-02 manual Other Management Options, Accessing the Switch Module, Interface

Models: OL-23421-02

1 46

Download 46 pages 8.57 Kb

Page 32

Other Management Options

Chapter 4 Managing the Switch Module

Other Management Options

Note You must be a registered Cisco.com user, but you need no other access privileges.

Step 2 Click Download Software.

Step 3 Select the latest release of the Configuration Professional installer, and click Download.

Note Cisco Configuration Professional 2.5 or later is supported on the switch module.

Step 4 Run the Configuration Professional installer, and follow the directions.

Step 5 Click Finish to complete the installation.

See the Configuration Professional Getting Started Guide and online help for more information.

Other Management Options

You can use SNMP management applications such as CiscoWorks LAN Management Solution (LMS) and Cisco netManager to configure and manage the switch module. You also can manage the switch module from an SNMP-compatible workstation that is running platforms such as Cisco netManager or SunNet Manager.

The Cisco Configuration Engine is a network management device that works with embedded Cisco Networking Services (CNS) agents in the switch software. You can use it to automate initial configurations and configuration updates on the switch.

Accessing the Switch Module

Note The Cisco CGR 2010 router must be running Cisco IOS Release 15.1(4)M or higher to run the switch module.

After the Ethernet switch module is installed on the router, you see a new Gigabit Ethernet interface 0/x/0 (where x is the slot number) recognized by the Cisco IOS. The output shown in Table 6 is taken after two Ethernet switch modules are installed on the router:

Router1#show ip interface brief

Table 4-1	Output for Gigabit Ethernet Interface Recognized on the Ethernet Switch Module

Interface		IP Address	OK?	Method	Status	Protocol

GigabitEthernet0/0		60.60.60.1	YES	NVRAM	down	down

GigabitEthernet0/1		80.80.80.1	YES	manual	up	up

GigabitEthernet0/0/0		100.0.0.1	YES	manual	up	up

GigabitEthernet0/2/0		200.0.0.1	YES	NVRAM	up	up

Cisco Connected Grid Ethernet Switch Module Interface Card Getting Started Guide

4-2	OL-23421-02

Image 32

Cisco Systems OL-23421-02 Other Management Options, Accessing the Switch Module, Interface, IP Address, Method, Status

Contents

Cisco Systems, Inc Cisco Connected Grid Ethernet SwitchModule Interface Card Getting Started Guide Text Part Number OL-23421-02No combinations are authorized or intended under this document 2012-2014 Cisco Systems, Inc. All rights reservedObtaining Documentation and Submitting a Service Request InstallationPre-Installation Switch ModelsCisco Configuration Professional Resetting the Switch ModuleManaging the Switch Module SFP Module ConnectorsDocument Conventions PrefacePurpose Related Publications Obtaining Documentation and Submitting a Service RequestSwitch Models Switch Models, page Ports, page LEDs, pageProduct Overview C H A P T E RPorts Port LocationsPort Locations, page Port Labeling, page 10/100BASE-T Ports, page PoE and PoE+ Ports, page 10/100 Mb/s SFP Module Slots, pageLabel Port LabelingPort GRWIC-D-ES-2S-8PC Port Labeling 10/100BASE-T PortsPoE and PoE+ Ports Dual-Purpose Gigabit Ethernet Ports 10/100 Mb/s SFP Module Slots100/1000 Mb/s SFP Module Slots Model Supported SFPsType of SFP Module LEDs Description GRWIC-D-ES-2S-8PC Switch Module Copper Model LEDsDescription Router Compact Flash Memory Cards 1-10 flash1flash or flash0Installation Pre-InstallationInstallation Warning Statements Pre-Installation Installation Connecting to the NetworkInstallation Figure 2-2 Positioning the Switch Module to Install in the Router Chapter 2 Installation InstallationFigure 2-1 Removing the Slot Divider From the CGR 2010 Router OL-23421-02Step 5 Tighten the screws Connecting to the Network Connecting the Copper Switch ModuleConnecting the Copper Switch Module, page Connecting the Fiber Switch Module, pageConnecting the Fiber Switch Module Figure 2-5 Connecting the Copper Model to the NetworkRemoving the Switch Module Chapter 2 Installation Removing the Switch Module OL-23421-02Express Setup Express SetupSystem Requirements Express Setup Troubleshooting Express Setup Resetting the Switch ModuleStep 2 Verify that no device is connected to the switch module Step 6 Select one of the following Step 3 Enter the Network Settings values Troubleshooting Express Setup Resetting the Switch ModuleProblem ResolutionOL-23421-02 Step 3 Follow the steps in Express Setup, pageChapter 3 Express Setup Resetting the Switch Module Managing the Switch Module Using the Device ManagerCisco Configuration Professional Using the Device Manager Cisco Configuration ProfessionalAccessing the Switch Module Other Management OptionsInterface IP AddressDisconnecting from the Switch Module Connecting Devices to the Switch Module Dual-Purpose Port with RJ-45 and SFP Connectors, page10/100BASE-T Ports, page SFP Module Slots, page Dual-Purpose Port with RJ-45 and SFP Connectors, pageSFP Module Slots 237940237941 237942Figure 4-3 Connecting the Cable into the SFP Port Chapter 4 Managing the Switch ModuleDual-Purpose Port with RJ-45 and SFP Connectors 237964 Figure 4-4 Ethernet Cable Connected to the RJ-45 Connector237965 Verifying Port ConnectivityFigure 4-5 Dual-Purpose Connectors 4-10 Chapter 4 Managing the Switch ModuleConnecting Devices to the Switch Module OL-23421-02Cable and Connectors Connector SpecificationsSFP Module Connectors Connector Specifications, page A-1 Cables and Adapters, page A-2Cables and Adapters Dual-Purpose PortsSFP Module Cables SFP Module Cables, page A-2 Cable Pinouts, page A-4Size/Cladding Cable Pinouts Four Twisted-Pair Crossover Cable Schematics for 1000BASE-T Ports Figure A-6Figure A-7 Figure A-8 Identifying a Crossover CableAppendix A Cable and Connectors Cables and Adapters OL-23421-02