general information

ALL MODELS

1.This manual is for the following Models--

113.248210,113.248320,113.248440, and113.248510. All sections are labeled with the correct model num- ber. Follow ONLY instructions that are meant for

your model saw.

2.Ifyou aremissing anypart(s)whileputtingyour saw together, do not continue assembly. Contact your Sears Service Center or Retail Store and get the

missing part(s) before continuing assembly or try- ing to use the saw.

Complete parts lists are located at the end of this manual. Use these liststo identifythe number of any

missing part.

3.Sometimes small parts get lost in packaging materi- als. Do not throw away any packaging until your saw is put together. If you are missing a part, check the packaging before contacting Sears.

Model Description

Model 113.248210: Manual Band Saw; 18x 23 inch work table; sLngle speed; 1/2H.P. motor that develops 1 H.P.; legset.

Model 113.248320: Manual Band Saw; 27 x 23 inch work table; two speed; 5/a H.P. motor that develops 11/8H.R; legset.

Model 113.248440: Electronic Band Saw; 27 x 23 inch work table; two speed; % H.P. motor that develops 11/8H.P.; legset.

Model 113.248510: Electronic Band Saw; 27 x 23 inch work table; two speed; 5/8 HP. motor that develops 11/8H.P.;23 inch cabinet with door.

unpacking and checking contents

ALL MODELS

TOOLS NEEDED

COMBINATION SQUARE MUST BE TRUE

STRAIGHT EDGE GF

BOARD 3/4-INCH THICK

THIS EDGE MUST BE

f__./

MEDIUM SCREWDRIVER

PER_CTLY STRAIGHT

PRI-,, SSCREWDRmVE.

 

@

 

 

 

..........

 

 

 

318" WRENCH

DRAW

LIGHT

 

:_

 

 

 

 

7/16"

WRENCH

LINE

ON

BOARD

 

 

 

 

ALONG

 

THIS

EDGIE

 

 

 

 

 

9/16"

WRENCH

 

SQUARE

_/

 

 

 

 

 

 

t,_

 

 

 

 

7116"

SOCKET

 

 

 

 

/

 

 

 

 

9/16"

SOCKET

 

 

 

 

1/8"

HEX

"L"

WRENCH

 

 

 

 

 

 

5/32"

HEX

"L"

WRENCH

_

SOCKET WRENCH

 

 

 

 

 

 

 

 

 

 

SHOULD BE NO GAP OR OVERLAP HERE WHEN

 

 

 

 

 

 

 

SQUARE

IS

FLIPPED OVER IN DOTTED POSITION

WARNING: TO AVOID INJURY FROM UNEXPECT- ED STARTING OR ELECTRICAL SHOCK, DO NOT PLUG THE SAW IN UNTIL ALL ASSEMBLY AND

ALIGNMENT STEPS ARE COMPLETE. THE POWER CORD MUST REMAIN UNPLUGGED WHENEVER YOU ARE WORKING ON THE SAW.

Unpacking and Checking Contents

1.Separate all "loose parts" from packaging mater- ials and check each item with "Table of Loose Parts" to make sure all items are accounted for, before discarding any packing material.

WARNING: IF ANY PARTS ARE MISSING, DO NOT ATTEMPT TO ASSEMBLE THE BAND

SAW, PLUG IN THE POWER CORD, OR TURN THE SWITCH ON UNTIL THE MISSING PARTS

ARE OBTAINED AND ARE INSTALLED COR- RECTLY.

2.Remove front table and front cover first while saw is being unpacked. TO remove the front

cover, pull thecover at the neck and underside of throat area.

Page 8
Image 8
Craftsman 113.248510 owner manual General information, Unpacking and checking contents