Cypress CY14B101K manual Register Map Detail Alarm Hours 0x1FFF4 10s Alarm Hours

									CY14B101K
Table 5. Register Map Detail (continued)
						Alarm - Hours
0x1FFF4	D7	D6		D5		D4	D3	D2	D1	D0
	M			10s Alarm Hours				Alarm Hours
	Contains the alarm value for the hours and the mask bit to select or deselect the hours value.
M	Match. When this bit is set to 0, the hours value is used in the alarm match. Setting this bit to 1 causes the match circuit
	to ignore the hours value.
						Alarm - Minutes
0x1FFF3	D7	D6		D5		D4	D3	D2	D1	D0
	M		10s Alarm Minutes					Alarm Minutes
	Contains the alarm value for the minutes and the mask bit to select or deselect the minutes value.
M	Match. When this bit is set to 0, the minutes value is used in the alarm match. Setting this bit to 1 causes the match
	circuit to ignore the minutes value.
						Alarm - Seconds
0x1FFF2	D7	D6		D5		D4	D3	D2	D1	D0
	M		10s Alarm Seconds					Alarm Seconds
	Contains the alarm value for the seconds and the mask bit to select or deselect the seconds’ value.
M	Match. When this bit is set to 0, the seconds value is used in the alarm match. Setting this bit to 1 causes the match
	circuit to ignore the seconds value.
					Time Keeping - Centuries
	D7	D6		D5		D4	D3	D2	D1	D0
0x1FFF1			10s Centuries					Centuries
	Contains the BCD value of centuries. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble contains
	the upper digit and operates from 0 to 9. The range for the register is 0-99 centuries.
						Flags
0x1FFF0	D7	D6		D5		D4	D3	D2	D1	D0
	WDF	AF		PF		OSCF	0	CAL	W	R
WDF	Watchdog Timer Flag. This read only bit is set to 1 when the watchdog timer is allowed to reach 0 without being reset
	by the user. It is cleared to 0 when the Flags register is read or on power-up.
AF	Alarm Flag. This read only bit is set to 1 when the time and date match the values stored in the alarm registers with the
	match bits = 0. It is cleared when the Flags register is read or on power-up.
PF	Power Fail Flag. This read only bit is set to 1 when power falls below the power fail threshold VSWITCH. It is cleared to
	0 when the Flags register is read or on power-up.
OSCF	Oscillator Fail Flag. Set to 1 on power up if the oscillator is enabled and not running in the first 5 ms of operation. This
	indicates that RTC backup power failed and clock value is no longer valid. The user must reset this bit to 0 to clear this
	condition (Flag). The chip does not clear this flag. This bit survives power cycles.
CAL	Calibration Mode. When set to 1, a 512 Hz square wave is output on the INT pin. When set to 0, the INT pin resumes
	normal operation. This bit defaults to 0 (disabled) on power up.
W	Write Enable: Setting the W bit to 1 freezes updates of the RTC registers. The user can then write to RTC registers,
	Alarm registers, Calibration register, Interrupt register and Flags register. Setting the W bit to 0 causes the contents of
	the RTC registers to be transferred to the time keeping counters if the time has been changed (a new base time is
	loaded). This bit defaults to 0 on power up.

RRead Enable: Setting R bit to 1, stops clock updates to user RTC registers so that clock updates are not seen during the reading process. Set R bit to 0 to resume clock updates to the holding register. Setting this bit does not require W bit to be set to 1. This bit defaults to 0 on power up.

Document Number: 001-06401 Rev. *I Page 14 of 28

[+] Feedback