Daewoo DF-4501P user manual VCR Playbackl, To return to normal playback, press Play

VCR Playbackl

Before You Begin

1Press the [VCR] button to set the remote control to operate the VCR deck.

2Turn the TV on and select the video input source connected to the DVD Recorder+VCR.

Audio system: Turn the audio system on and select the input source connected to the DVD Recorder+VCR.

Playing a VHS Tape

1Insert a prerecorded video cassette.

If the DVD Recorder+VCR is powered off, it will power on automatically.

Make sure the TIMER indicator on the front panel display is not lit. If it is, press [POWER] once.

If a tape without a safety tab is inserted, the DVD Recorder+VCR will start playback automatically.

If the DVD Recorder+VCR is powered on by inserting a video cassette, playback will not start automatically.

2Press [PLAY].

The PLAY icon appears on the TV screen. It is not necessary to select the tape speed (SP, LP) for playback. It will be automatically selected by the DVD Recorder+VCR.

3Press [STOP] to stop playback.

The STOP icon appears on the TV screen. If the tape reaches the end before [STOP] is pressed, the DVD Recorder+VCR will automatically stop, rewind, and eject the tape.

Tracking Control

Auto Tracking

The automatic tracking function adjusts the picture to remove snow or streaks. It works in the following cases:

•When a tape is played for the first time.

•When the tape speed (SP, LP) changes.

•When streaks or snow appear because of scratches on the tape.

Manual Tracking

If noise appears on the screen during playback, press the [TRACKING +/-] buttons on the remote control until the noise on the screen is reduced.

•In case of vertical jitter, adjust these controls very carefully.

•Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for more than 3 seconds.

VCR Playback

Special Playback Features

Notes on special playback features

Horizontal lines (noise bars) will appear on the TV screen. This is normal.

The audio is automatically muted during special playback modes, so there is no sound during search, slow motion, etc. During high-speed picture search, a short time is needed to stabilize tape speed when re-entering Play mode. Slight interference may be observed during this time.

Fast Forward/Backward

This function lets you visually search forward and backward for a desired scene on your tape.

1Press [REW] or [FF] during playback. Search mode will be activated.

If the DVD Recorder+VCR is left in Search mode for more than 3 minutes, the DVD Recorder+VCR will automatically resume Play mode to protect the tape and video heads.

2To return to normal playback, press [PLAY].

Still Picture
1	Press [PLAY/PAUSE] during playback.
	A still picture appears on the TV screen.
	If a still picture vibrates vertically, stabilize it by using the [TRACKING +/-] buttons on the remote control.
	If the DVD Recorder+VCR is left in Still mode for more than 5 minutes, the DVD Recorder+VCR will	PLAYBACK
2	automatically enter Stop mode to protect the tape and video heads.
	To return to normal playback, press [PLAY].

Slow Motion

1Press [SLOW+] for Slow Motion playback.

2Press [SLOW+] and [SLOW-] repeatedly to adjust the Slow Motion playback speed.

Counter Memory Function

This is useful if there is a section of tape you want to view immediately after recording or if you want to return to the same point several times.

1Begin recording or playing a tape.

2At the point you want to locate later, reset the real-time counter to 0:00:00 by pressing [CLEAR]. Continue to play or record.

3Press [STOP] when recording or playback finishes.

4You can make the tape automatically stop when the counter returns to about ‘0:00:00‘ by selecting "Go-to- Zero" function under ‘SETUP’ ➝ ’Preferences’ ➝ ’VCR’. See page 27.

34 35