Datalogic Scanning 400 1 RAPID CONFIGURATION

RAPID CONFIGURATION

1

1

1 RAPID CONFIGURATION

STEP 1 – ASSEMBLE THE READER

The first step to perform is to assemble the accessories that make up the Matrix 400™

reader. The lens and either an internal or an external illuminator must be used. This

procedure shows an internal illuminator.

CAUTION

Matrix 400™ must be disconnected from the power supply during this

procedure.

1. In a dust-free environment, remove the Matrix 400™ Lens Cover by unscrewing it.

CAUTION

Do not touch the sensor aperture, lens glass or lens cover glass. These

areas must be kept clean. Avoid any abrasive substances that might damage

these surfaces during cleaning.

2. Remove the sensor protection label by pulling it off of the base.

3. Mount the lens by screwing it tightly onto the base.

4. If using an internal illuminator:

a. Mount the 4 internal illuminator spacers into the holes provided on the base.

b. Align and mount the Illuminator board tightly onto the spacers using the 4 screws

provided in the illuminator package. The spacers are positioned asymmetrically to

avoid incorrect alignment.

5. To keep dust and dirt off of the lens during mounting, temporarily replace the lens cover.

Figure 1 – Assembling Matrix 400™ Accessories

Locking Knobs Internal

Illuminator

Lens Cover

Illuminator Spacers

Contents

Main Page CONTENTS Page Page REFERENCES CONVENTIONS REFERENCE DOCUMENTATION SERVICE AND SUPPORT PATENTS COMPLIANCE EMC COMPLIANCE POWER SUPPLY LED CLASS CE COMPLIANCE HANDLING Page GENERAL VIEW Matrix 400 1 RAPID CONFIGURATION STEP 1 ASSEMBLE THE READER Required Accessories STEP 2 CONNECT THE SYSTEM CBX100/CBX500 Pinout for Matrix 400 19-pin Connector Pinout for Matrix 400 STEP 3 MOUNT AND POSITION THE READER STEP 4 FOCUS THE READER STEP 5 CALIBRATE IMAGE DENSITY Locate Setup Learn STEP 6 X-PRESS CONFIGURATION Locate Setup Learn STEP 7 INSTALLING VISISET CONFIGURATION PROGRAM STEP 8 CONFIGURATION USING SETUP WIZARD Page Page Page Page Page STEP 9 TEST MODE ADVANCED READER CONFIGURATION Advanced Configuration Using VisiSet Host Mode Programming Alternative Layouts Code Quality Verification 2 INTRODUCTION 2.1 PRODUCT DESCRIPTION Page Page Page 2.2 INDICATORS AND KEYPAD BUTTON 2.3 ID-NET 2.3.1 How To Setup/Configure the Reader Network Page 2.4 X-PRESS HUMAN MACHINE INTERFACE 2.4.1 X-PRESS Functions Test Mode (Function 1) Focus/Locate (Function 2) Setup (Function 3) Learn (Function 4) 2.5 MODEL DESCRIPTION INTRODUCTION 2 2.6 ACCESSORIES The following accessories can be used with the Matrix 400 reader. Accessory Description Order No. 2.7 APPLICATION EXAMPLES Page Page 2.8 EXTERNAL LIGHTING SYSTEMS Page Page Page 3 INSTALLATION 3.1 PACKAGE CONTENTS 3.2 MECHANICAL DIMENSIONS INSTALLATION Figure 42 - Mounting Bracket Overall Dimensions 3.3 MOUNTING AND POSITIONING MATRIX 400 4 CBX ELECTRICAL CONNECTIONS 4.1 POWER SUPPLY 4.2 MAIN SERIAL INTERFACE 4.2.1 RS232 Interface 4.2.2 RS485 Full-Duplex Interface 4.2.3 RS485 Half-Duplex Interface Page 4.3 ID-NET INTERFACE 4.3.1 ID-NET Cables 4.3.2 ID-NET Response Time Page Page Page 4.3.3 ID-NET Network Termination 4.4 AUXILIARY RS232 INTERFACE 4.5 INPUTS Page 4.6 OUTPUTS Page 4.7 EXTERNAL LIGHTING SYSTEMS 4.8 USER INTERFACE - HOST 5 MATRIX 400 CONNECTOR ELECTRICAL CONNECTIONS 5.1 M16 19-PIN CONNECTOR 5.2 M12-D 4-PIN CONNECTOR (ETHERNET) 5.3 POWER SUPPLY 5.4 MAIN SERIAL INTERFACE 5.4.1 RS232 Interface 5.4.2 RS485 Full-Duplex Interface 5.4.3 RS485 Half-Duplex Interface Page 5.5 ID-NET INTERFACE 5.5.1 ID-NET Cables 5.5.2 ID-NET Response Time Page Page Page 5.5.3 ID-NET Network Termination 5.6 AUXILIARY RS232 INTERFACE 5.7 ETHERNET INTERFACE (MATRIX 400 XXX-010 MODELS ONLY) 5.8 INPUTS 5.9 OUTPUTS Page 5.10 USER INTERFACE 6 TYPICAL LAYOUTS 6.1 POINT-TO-POINT Page 6.2 PASS-THROUGH Page 6.3 ID-NET Page Page 6.4 RS232 MASTER/SLAVE 6.5 MULTIPLEXER 6.6 ETHERNET CONNECTION (MATRIX 400 XXX-010 MODELS ONLY) Page 7 READING FEATURES 7.1 OPTICAL ACCESSORY SELECTION FOVx = 2 (d + 35 mm) tan (x/2) d 7.2 HORIZONTAL FOV VS. READING DISTANCE DIAGRAMS 7.2.1 How to Use the Diagrams READING FEATURES 7.2.2 1D (Linear) Codes SXGA - 25 mm SXGA - 35 mm SXGA - 50 mm Reading Distance (cm) 35 30 96 7 9 mm, 12.5 mm, 16 mm Reading Distance (cm) 45 7.2.3 2D (Bi-dimensional) Codes Reading Distance (cm) Reading Distance (cm) 2D Codes Matrix 400 400-0x0 (SXGA) 9 mm, 12.5 mm, 16 mm Horizontal FOV (cm) 7 2D Codes Matrix 400 600-0x0 (UXGA) 9 mm, 12.5 mm, 16 mm UXGA - 25 mm UXGA - 35 mm UXGA - 50 mm Reading Distance (cm) 20 15 7.3 MAXIMUM LINE SPEED AND EXPOSURE TIME CALCULATIONS T Line Speed T Page 8 SOFTWARE CONFIGURATION 8.1 VISISET SYSTEM REQUIREMENTS 8.2 INSTALLING VISISET 8.3 STARTUP 8.3.1 VisiSet Options Page 8.4 CONFIGURATION 8.4.1 Edit Reader Parameters Page 8.4.2 Send Configuration Options Page Page 8.4.3 Calibration Page Page Page 8.4.4 Multi Image Acquisition Settings 8.4.5 Run Time Self Tuning (RTST) From Not Readable to Readable 8.4.6 Region Of Interest Windowing 8.4.7 Direct Part Marking Applications Page 8.5 IMAGE CAPTURE AND DECODING 8.6 STATISTICS 9 MAINTENANCE 9.1 CLEANING 10 TROUBLESHOOTING 10.1 GENERAL GUIDELINES Page Page 11 TECHNICAL FEATURES Page GLOSSARY Page Page INDEX Matrix 4XX YYY-ZZZ e tutti i suoi modelli 89/336/EEC EMC Directive EN 55022 (Class A ITE), September 1998 EN 61000-6-2, September 2005