Datalogic Scanning 400 STEP 9 TEST MODE

MATRIX 400™ REFERENCE MANUAL

STEP 9 – TEST MODE

Use a code suitable to your application to test the reading performance of the system.

1. Enter the Test function by pressing and holding the X-PRESS™ push button until the

Test LED is on.

2. Release the button to enter the Test function.

Once entered, the Bar Graph on the five LEDs is activated and if the reader starts

reading codes the Bar-Graph shows the Good Read Rate. In case of no read condition,

only the STATUS LED is on and blinks.

READY

green

ellow

red

SETU

FOCUS

LEARN

GOOD

RIGGER

COM

STATUS

Figure 17 – X-PRESS™ Interface: Test Function

3. To exit the Test, press the X-PRESS™ push button once.

NOTE

By default, the Test exits automatically after three minutes.

The Bar Graph has the following meaning:

READY



95%



75%



60%



40%



20%

SETUP

FOCUS

LEARN

GOOD

RIGGER

COM

STATUS

Contents

Main Page CONTENTS Page Page REFERENCES CONVENTIONS REFERENCE DOCUMENTATION SERVICE AND SUPPORT PATENTS COMPLIANCE EMC COMPLIANCE POWER SUPPLY LED CLASS CE COMPLIANCE HANDLING Page GENERAL VIEW Matrix 400 1 RAPID CONFIGURATION STEP 1 ASSEMBLE THE READER Required Accessories STEP 2 CONNECT THE SYSTEM CBX100/CBX500 Pinout for Matrix 400 19-pin Connector Pinout for Matrix 400 STEP 3 MOUNT AND POSITION THE READER STEP 4 FOCUS THE READER STEP 5 CALIBRATE IMAGE DENSITY Locate Setup Learn STEP 6 X-PRESS CONFIGURATION Locate Setup Learn STEP 7 INSTALLING VISISET CONFIGURATION PROGRAM STEP 8 CONFIGURATION USING SETUP WIZARD Page Page Page Page Page STEP 9 TEST MODE ADVANCED READER CONFIGURATION Advanced Configuration Using VisiSet Host Mode Programming Alternative Layouts Code Quality Verification 2 INTRODUCTION 2.1 PRODUCT DESCRIPTION Page Page Page 2.2 INDICATORS AND KEYPAD BUTTON 2.3 ID-NET 2.3.1 How To Setup/Configure the Reader Network Page 2.4 X-PRESS HUMAN MACHINE INTERFACE 2.4.1 X-PRESS Functions Test Mode (Function 1) Focus/Locate (Function 2) Setup (Function 3) Learn (Function 4) 2.5 MODEL DESCRIPTION INTRODUCTION 2 2.6 ACCESSORIES The following accessories can be used with the Matrix 400 reader. Accessory Description Order No. 2.7 APPLICATION EXAMPLES Page Page 2.8 EXTERNAL LIGHTING SYSTEMS Page Page Page 3 INSTALLATION 3.1 PACKAGE CONTENTS 3.2 MECHANICAL DIMENSIONS INSTALLATION Figure 42 - Mounting Bracket Overall Dimensions 3.3 MOUNTING AND POSITIONING MATRIX 400 4 CBX ELECTRICAL CONNECTIONS 4.1 POWER SUPPLY 4.2 MAIN SERIAL INTERFACE 4.2.1 RS232 Interface 4.2.2 RS485 Full-Duplex Interface 4.2.3 RS485 Half-Duplex Interface Page 4.3 ID-NET INTERFACE 4.3.1 ID-NET Cables 4.3.2 ID-NET Response Time Page Page Page 4.3.3 ID-NET Network Termination 4.4 AUXILIARY RS232 INTERFACE 4.5 INPUTS Page 4.6 OUTPUTS Page 4.7 EXTERNAL LIGHTING SYSTEMS 4.8 USER INTERFACE - HOST 5 MATRIX 400 CONNECTOR ELECTRICAL CONNECTIONS 5.1 M16 19-PIN CONNECTOR 5.2 M12-D 4-PIN CONNECTOR (ETHERNET) 5.3 POWER SUPPLY 5.4 MAIN SERIAL INTERFACE 5.4.1 RS232 Interface 5.4.2 RS485 Full-Duplex Interface 5.4.3 RS485 Half-Duplex Interface Page 5.5 ID-NET INTERFACE 5.5.1 ID-NET Cables 5.5.2 ID-NET Response Time Page Page Page 5.5.3 ID-NET Network Termination 5.6 AUXILIARY RS232 INTERFACE 5.7 ETHERNET INTERFACE (MATRIX 400 XXX-010 MODELS ONLY) 5.8 INPUTS 5.9 OUTPUTS Page 5.10 USER INTERFACE 6 TYPICAL LAYOUTS 6.1 POINT-TO-POINT Page 6.2 PASS-THROUGH Page 6.3 ID-NET Page Page 6.4 RS232 MASTER/SLAVE 6.5 MULTIPLEXER 6.6 ETHERNET CONNECTION (MATRIX 400 XXX-010 MODELS ONLY) Page 7 READING FEATURES 7.1 OPTICAL ACCESSORY SELECTION FOVx = 2 (d + 35 mm) tan (x/2) d 7.2 HORIZONTAL FOV VS. READING DISTANCE DIAGRAMS 7.2.1 How to Use the Diagrams READING FEATURES 7.2.2 1D (Linear) Codes SXGA - 25 mm SXGA - 35 mm SXGA - 50 mm Reading Distance (cm) 35 30 96 7 9 mm, 12.5 mm, 16 mm Reading Distance (cm) 45 7.2.3 2D (Bi-dimensional) Codes Reading Distance (cm) Reading Distance (cm) 2D Codes Matrix 400 400-0x0 (SXGA) 9 mm, 12.5 mm, 16 mm Horizontal FOV (cm) 7 2D Codes Matrix 400 600-0x0 (UXGA) 9 mm, 12.5 mm, 16 mm UXGA - 25 mm UXGA - 35 mm UXGA - 50 mm Reading Distance (cm) 20 15 7.3 MAXIMUM LINE SPEED AND EXPOSURE TIME CALCULATIONS T Line Speed T Page 8 SOFTWARE CONFIGURATION 8.1 VISISET SYSTEM REQUIREMENTS 8.2 INSTALLING VISISET 8.3 STARTUP 8.3.1 VisiSet Options Page 8.4 CONFIGURATION 8.4.1 Edit Reader Parameters Page 8.4.2 Send Configuration Options Page Page 8.4.3 Calibration Page Page Page 8.4.4 Multi Image Acquisition Settings 8.4.5 Run Time Self Tuning (RTST) From Not Readable to Readable 8.4.6 Region Of Interest Windowing 8.4.7 Direct Part Marking Applications Page 8.5 IMAGE CAPTURE AND DECODING 8.6 STATISTICS 9 MAINTENANCE 9.1 CLEANING 10 TROUBLESHOOTING 10.1 GENERAL GUIDELINES Page Page 11 TECHNICAL FEATURES Page GLOSSARY Page Page INDEX Matrix 4XX YYY-ZZZ e tutti i suoi modelli 89/336/EEC EMC Directive EN 55022 (Class A ITE), September 1998 EN 61000-6-2, September 2005