Datalogic Scanning 90ACC1780

Enter configuration

ik

CODE SELECTION

Exit and Save Configuration

i k

CONVERSION OPTIONS

UPC E to UPC A conversion

i"""ak

UPC E to EAN 13 conversion

i""#dk

UPC A to EAN 13 conversion

i""$gk

EAN 8 to EAN 13 conversion

i""%k

enable only ISBN conversion

i"1Ok

enable only ISSN conversion

i"1Rk

enable both ISBN and ISSN conversion

i"1Uk

disable both ISBN and ISSN conversion

i"1Lk

Contents

Main Page GRYPHON Page CONTENTS Page Page Page Page GENERAL VIEW 1 INTRODUCTION 2 INSTALLATION 2.1 GRYPHON D INTERFACE CABLE CONNECTIONS 2.2 OM-GRYPHON INTERFACE CABLE CONNECTIONS 2.3 RS232 CONNECTION 2.4 WEDGE CONNECTION 2.5 PEN EMULATION CONNECTION 2.6 GRYPHON M BATTERY MAINTENANCE 2.6.1 Battery Type 2.6.2 Battery Charging 2.6.3 Replacing GRYPHON M Batteries 1. 1.1. 1. Page 3 GRYPHON M SYSTEM AND NETWORK LAYOUTS 3.1 STAND ALONE LAYOUTS 3.1.1 Single Reader Layout 3.1.2 Multiple Reader Layout 3.1.3 Multiple Stand Alone Layouts 3.2 MULTIDROP STAR-SYSTEM NETWORK LAYOUTS 3.2.1 Host Master Layout 4 CONFIGURATION 4.1 CONFIGURATION METHODS 4) 3) 2) 4.1.4 Sending Configuration Strings from Host 4.2 SETUP PROCEDURES Page 5. 7. 6. 5. END of procedure. Page 4.5 GRYPHON M/STAR-SYSTEM SETUP 1. 2. 3. 4. Page 4.6 INTERFACE SELECTION Page Page Page Page 4.7 CHANGING DEFAULT SETTINGS RS232 PARAMETERS Page Page Page Page RS232 X ELAY HARACTER RS232 NLY ERIES (D S WEDGE PARAMETERS ATIONALITY EYBOARD K N Page Page ETTING EYBOARD K Page Page PEN EMULATION Page ULSE UTPUT INIMUM ODE AND ODE O Page EVEL ELAY LOCK -B DATA FORMAT CODE IDENTIFIER TABLE Page Page DENTIFIER i&'k ODE USTOM Page Page DJUSTMENT IELD DJUSTMENT X ENGTH ODE EPLACEMENT HARACTER i&0Qk i&0Tk (M S ) (M S ) POWER SAVE Page POWER SAVE TANDBY LEEP NTER READING PARAMETERS PERATING PERATION -H H PERATION H FF LASH -O YCLE IME AFETY EADS PER NTENSITY ONE EEPER EEPER PDF D Page DECODING PARAMETERS Page Page DECODING PARAMETERS OLVER UZZLE CODE SELECTION Page Page Page Page Page AMILY 2/5 F 39 F Page Page Page AMILY ODABAR Page Page Page Page Page ELTA IBM Page Page Page ADVANCED FORMATTING C A Page Page Page ORMATTING DVANCED 97 Page Page Page Page Page Page Page Page Page Page Page Page Page Page RADIO PARAMETERS RADIO PARAMETERS FF -O OWER Page Page 5 REFERENCES 5.1 RS232 PARAMETERS 5.1.1 Handshaking 5.1.2 ACK/NACK Protocol 5.1.3 FIFO 5.1.4 RX Timeout 5.2 PEN PARAMETERS 5.2.1 Minimum Output Pulse 5.2.2 Conversion to Code 39 and Code 128 5.2.3 Overflow 5.2.4 Output and Idle Levels 5.2.5 Inter-Block Delay 5.3 DATA FORMAT CODE CODE 5.3.1 Header/Terminator Selection For the WEDGE interface, the following extended keyboard values can also be configured: 5.3.2 Set Custom Extended Header/Terminator Keys users Wedge Interface Example: CUSTOM EXTENDED KEYBOARD SETTING TABLE 5 5.3.3 Address Stamping 5.3.4 Address Delimiter 5.4 POWER SAVE 5.4.1 Sleep State 5.4.3 Standby one read per cycle trigger active level 5.5.3 Trigger-Off Timeout 5.5.4 Reads per Cycle 5.5.5 Safety Time 5 5.6 DECODING PARAMETERS 5.6.1 Ink-Spread 5.6.2 Overflow Control 5.6.3 Interdigit Control 5.7 RADIO PARAMETERS (M SERIES ONLY) 5.7.2 Power-Off Timeout 5.7.3 Beeper Control for Radio Response For all configurations, any transmission errors will always be signaled. 5.7.4 Single Store 5.8 CONFIGURATION EDITING COMMANDS Command Description 5.9 CONFIGURATION COPYING COMMANDS 5.9.1 Copy GRYPHON D-Series 5.9.2 Copy GRYPHON M-Series 5.9.3 Copy OM-GRYPHON 5 5.10 C-GRYPHON CONFIGURATION 1. Alkaline 2. 5.11 DEFAULT PARAMETERS FOR POS TERMINALS 6 6 TECHNICAL FEATURES 6.1 GRYPHON D Electrical Features Optical Features Environmental Features 6.2 GRYPHON M Electrical Features Optical Features Environmental Features Mechanical Features 6.3 OM-GRYPHON / C-GRYPHON Host Interfaces OM-GRYPHON C-GRYPHON Electrical and General Features Environmental Features 6.4 SYSTEM AND RADIO FEATURES 6.5 STATUS INDICATORS Page 6 OM-GRYPHON/C-GRYPHON CHARGE STATUS OM-GRYPHON/C-GRYPHON POWER/COMMUNICATION 6.6 READING DIAGRAMS GRYPHON D/M100 GRYPHON 142 6 GRYPHON D/M200 10 5 0 -5 APPENDIX A HOST CONFIGURATION STRINGS Command CR$-$+ SERIAL CONFIGURATION STRINGS Page Page Page Page Page Page Page Page Page Page APPENDIX B CODE IDENTIFIER TABLE Page Page Page APPENDIX C HEX AND NUMERIC TABLE