LED and Beeper Indications
INDICATION | DESCRIPTION | LED | BEEPER | |
|
|
|
| |
|
|
|
| |
| The imager is in the process of pow- |
| Imager beeps four times at highest | |
| frequency and volume upon power- | |||
| ||||
|
| up. | ||
|
|
| ||
|
|
|
| |
|
| LED behavior for this indica- | The imager will beep once at cur- | |
Good Read Beep | A label has been successfully | tion is configurable via the | rent frequency, volume, mono/bi- | |
scanned by the imager. | feature “Good Read: When to | tonal setting and duration upon a | ||
| ||||
|
| Indicate” | successful label scan. | |
|
|
|
| |
ROM Failure | There is an error in the imager's | Flashes | Imager sounds one error beep at | |
software/programming | highest volume. | |||
|
| |||
|
|
|
| |
Limited Scanning | Indicates that a host connection is |
| Imager 'chirps' six times at the high- | |
not established when the IBM or | N/A | |||
Label Read | est frequency and current volume. | |||
USB interface is enabled. |
| |||
|
|
| ||
|
|
|
| |
Imager Active | The imager is active and ready to | The LED is lit steadilya | N/A | |
Mode | scan. | |||
|
| |||
|
|
|
| |
Imager | The imager has been disabled by | The LED blinks continuously | N/A | |
Disabled | the host. | |||
|
| |||
|
|
|
| |
| While in Stand Mode or Trigger |
|
| |
Green Spot is on | Object Sense mode the green spot | N/A | N/A | |
continuously | shall be on while in stand watch | |||
|
| |||
| state. |
|
| |
|
|
|
| |
Green Spota | Upon successful read of a label, the |
|
| |
software shall turn the green spot on |
|
| ||
flashes momen- | N/A | N/A | ||
for the time specified by the config- | ||||
tarily |
|
| ||
ured value. |
|
| ||
|
|
| ||
|
|
|
| |
Programming Mode - The following indications ONLY occur when the imager is in Programming Mode. | ||||
|
|
|
| |
Label Programming | A valid programming label has been | LED blinks continuously | Imager sounds four low frequency | |
Mode Entry | scanned. | beeps. | ||
| ||||
|
|
|
| |
Label Programming |
|
| Imager sounds three times at low- | |
Mode Rejection of | A label has been rejected. | N/A | ||
est frequency & current volume. | ||||
Label |
|
| ||
|
|
| ||
|
|
|
| |
| In cases where multiple labels must |
|
| |
Label Programming | be scanned to program one feature, |
| Imager sounds one short beep at | |
Mode Acceptance | this indication acknowledges each | N/A | ||
highest frequency & current volume. | ||||
of Partial Label | portion as it is successfully |
| ||
|
| |||
| scanned. |
|
| |
|
|
|
| |
Label Programming | Configuration option(s) have been |
| Imager sounds one high frequency | |
successfully programmed via labels |
| |||
Mode Acceptance | N/A | beep and 4 low frequency beeps | ||
and the imager has exited Program- | ||||
of Programming |
| followed by reset beeps. | ||
ming Mode. |
| |||
|
|
| ||
|
|
|
| |
Label Programming |
|
| Imager sounds two times at low fre- | |
Mode Cancel Item | Cancel label has been scanned. | N/A | ||
quency and current volume. | ||||
Entry |
|
| ||
|
|
| ||
a.Except when in sleep mode or when a Good Read LED Duration other than 00 is selected
284 | QuickScan® QD2100 |
