Caution: Safety Instructions (continued)

Rack Mounting of Systems

Observe the following precautions for rack stability and safety. Also refer to the rack installation documentation accompanying the system and the rack for specific caution statements and procedures.

Systems are considered to be components in a rack. Thus, "component" refers to any system as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front and side stabilizers installed could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances. Therefore, always install the stabilizers before installing components in the rack.

After installing system/components in a rack, never pull more than one component out of the rack on its slide assemblies at one time. The weight of more than one extended component could cause the rack to tip over and may result in serious injury.

NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a Dell™ rack cabinet using the customer rack kit. The installation of your system and rack kit in any other rack cabinet has not been approved by any safety agencies. It is your responsibility to have the final combination of system and rack kit in a rack cabinet evaluated for suitability by a certified safety agency. Dell disclaims all liability and warranties in connection with such combinations.

•System rack kits are intended to be installed in a rack by trained service technicians. If you install the kit in any other rack, be sure that the rack meets the specifications of a Dell rack.

CAUTION: Do not move racks by yourself. Due to the height and weight of the rack, a minimum of two people should accomplish this task.

•Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack.

•Always load the rack from the bottom up, and load the heaviest item in the rack first.

•Make sure that the rack is level and stable before extending a component from the rack.

•Use caution when pressing the component rail release latches and sliding a component into or out of a rack; the slide rails can pinch your fingers.

Dell PowerConnect RPS-600 Setup Guide

7

Page 7 Page 9
Page 8
Image 8
Dell RPS-600, 2T227 setup guide Rack Mounting of Systems
Page 7 Page 9

2T227, RPS-600 specifications

The Dell RPS-600, model 2T227, is a robust and efficient power supply solution designed specifically for Dell's PowerEdge servers. This unit is particularly favored in configurations where high availability and redundancy are critical components of the system architecture. The RPS-600 is known for its reliability and performance, making it an ideal choice for businesses that require consistent uptime.

One of the standout features of the RPS-600 is its impressive power output capacity of 600 watts, which provides ample energy supply for even the most demanding server configurations. This power supply unit operates efficiently, ensuring that the servers run optimally while consuming minimal energy. The high efficiency is supported by a design that meets the 80 PLUS certification, indicating that it operates at least 80% efficiency at various loads, thus minimizing wasted energy and reducing operational costs.

The RPS-600 is designed to work with Dell's redundant power supplies, allowing for seamless failover in case of any power supply failure. This feature is essential for enterprises that cannot afford any system downtime. The unit is equipped with a hot-swappable design, allowing IT administrators to replace the power unit without having to shut down the server, ensuring continuous operation during maintenance or upgrades.

In terms of connectivity, the RPS-600 features a standard input connector that ensures compatibility with a wide range of Dell servers. The power supply is also designed with built-in protections that safeguard against common electrical issues such as overvoltage, overcurrent, and short circuits. This enhances both the reliability and the longevity of the connected hardware.

Furthermore, the Dell RPS-600 supports a wide input voltage range, making it flexible for use in various environments and geographic locations. Its compact form factor allows it to fit seamlessly into server racks, maximizing space utilization while ensuring optimal airflow and cooling.

Overall, the Dell RPS-600,2T227, embodies advanced features and technologies that cater to the demands of modern data centers and businesses. With its focus on efficiency, reliability, and ease of maintenance, it remains a top choice for organizations looking to enhance their server's performance while ensuring maximum uptime and minimal operational costs.
Top Page Image Contents